How to Service a Turn Signal Switch on Dodge Ram 1500?

To service the turn signal switch, first disconnect and isolate the battery negative cable. If applicable, unscrew the lever from the tilt steering column adjuster mechanism located on the left side of the column just below the multi-function switch stalk by turning it counterclockwise. Remove both the upper and lower shrouds from the steering column, followed by the lower fixed column shroud. Move the upper fixed column shroud to access the back of the multi-function switch, then remove the tamper proof mounting screws using a Snap On tamper proof Torx bit TTXR2OB2 or equivalent. Gently pull the multi-function switch away from the steering column to access and remove the screw securing the instrument panel wire harness connector to the multi-function switch connector receptacle, then disconnect the instrument panel wire harness connector. Remove the multi-function switch from the steering column. For installation, position the multi-function switch onto the steering column and reconnect the instrument panel wire harness connector to the multi-function switch connector receptacle. Install and tighten the screw securing the instrument panel wire harness connector to the multi-function switch connector receptacle to 2 Nm (17 in. lbs.), then install and tighten the two screws securing the multi-function switch to the steering column to the same torque specification. Install the lower fixed column shroud, followed by both the upper and lower shrouds onto the steering column. If applicable, install the tilt steering column lever onto the left side of the steering column by screwing it into place, and finally reconnect the battery negative cable.

OEM Dodge Ram 1500 Turn Signal Switch

Turn Signal Indicator Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Turn Signal Switches found

View related parts
Dodge Ram 1500 Multifunction Switch Part Number: 56046114AF
$154.09 MSRP: $231.00
You Save: $76.91 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Windshield Washer Switch.; Wiper Switch; Switch Multifunction
- Replaces: 56046114AD, 56046114AC, 56046114AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Ram 1500 | Laramie, SLT, Sport, ST, TRX, TRX4 | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 1500 Multifunction Switch Part Number: 56044802AC
$211.12 MSRP: $318.00
You Save: $106.88 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Combination Switch; Multi Purpose Switch; Switch Multifunction
- Replaces: 56044802AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Dodge Ram 1500 | Laramie, SLT, ST, SXT | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Ram 1500 Ignition Switch Part Number: 4728424
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Windshield Washer Switch.; Turn Signal Switch; Multifunction, Wiper, Headlamp Dimmer, Hazard, Signal & Tilt options.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-2002 Dodge Ram 1500 | Base, LT, Laramie, SLT, SS/T 5.9L, ST, Sport, WS | 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Ram 1500 Turn Signal Switch Part Number: 56049823AB
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Switch; Air Bag Clockspring.; Multifunction Switch; Switch Housing; Ignition Housing; Clockspring; Switch Multifunction
- Replaces: 56045515AA, 56049823AA, 56045165AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2008 Dodge Ram 1500 | Laramie, SLT, Sport, SRT-10, ST, SXT, TRX4 | 10 Cyl 8.3 L GAS, 3.7L V6, 4.7L V8, 5.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS, 8.3L V10

Dodge Ram 1500 Turn Signal Switch

Choose OEM Turn Signal Switch that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Turn Signal Switch follows strict manufacturing steps to lock in quality and fit. If your Dodge Ram 1500 matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Ram 1500 parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Ram 1500 Turn Signal Switch Parts and Q&A

Ignition Switch
4728424
Q:
How to Service a Turn Signal Switch on Dodge Ram 1500?
A:
To service the turn signal switch, first disconnect and isolate the battery negative cable. If applicable, unscrew the lever from the tilt steering column adjuster mechanism located on the left side of the column just below the multi-function switch stalk by turning it counterclockwise. Remove both the upper and lower shrouds from the steering column, followed by the lower fixed column shroud. Move the upper fixed column shroud to access the back of the multi-function switch, then remove the tamper proof mounting screws using a Snap On tamper proof Torx bit TTXR2OB2 or equivalent. Gently pull the multi-function switch away from the steering column to access and remove the screw securing the instrument panel wire harness connector to the multi-function switch connector receptacle, then disconnect the instrument panel wire harness connector. Remove the multi-function switch from the steering column. For installation, position the multi-function switch onto the steering column and reconnect the instrument panel wire harness connector to the multi-function switch connector receptacle. Install and tighten the screw securing the instrument panel wire harness connector to the multi-function switch connector receptacle to 2 Nm (17 in. lbs.), then install and tighten the two screws securing the multi-function switch to the steering column to the same torque specification. Install the lower fixed column shroud, followed by both the upper and lower shrouds onto the steering column. If applicable, install the tilt steering column lever onto the left side of the steering column by screwing it into place, and finally reconnect the battery negative cable.