How to adjust Steering Gear Box on Dodge Ramcharger?

Some sagging can be corrected by manual turning of the inner and outer rods even without the removal of the steering gear. For change of the worm bearing preload, you have to remove the Pitman arm from the sector shaft through the use of puller after removing the nut and the thrust washer. The horn pad has to be pulled off from the steering wheel Attachment 170 detects that the sector shaft screw locknut has to be unlocked and the screw has to be turned back by two turns at least. Twist the wheel by 720 degrees counter clockwise if right hand steered vehicle and vice versa, then using a socket on the steering wheel nut fasten a torque wrench to the steering shaft and rotate it back to the straight position while holding the torque steady to the prescribed limit. In case the torque wrench cannot be used, the spring balance could be used provided it is mounted one inch from the centre point of the socket wrench. In order to increase the worm bearing preload rotate the worm bearing adjuster in a clockwise direction and release the worm bearing preload locknut and then lock it when done. For sector gear adjustment turn the steering wheel to the left and then to the right as far as it can be turned, count the turns and then turn back half a turn. Tighten the sector shaft screw and lead screw until all the clearence between ball nut rack and corresponding teeth of sector gear have been eliminated and then tighten the lock nut. Check and turn the steering wheel a quarter turn from center and apply the measured force to return the steering wheel back to the center, should be within limits, adjust if necessary. Only when these adjustments have been made correctly, align the wheels and steering wheel, before fitting the Pitman arm on. For power steering sector shaft adjustment, the relay rod ball joint taper pin should be disconnected from the Pitman arm, the engine should be switched on and the same should be allowed to run on the idle condition. With the wheel in the straight-ahead position spin it from side to side through 10 smaller turns and back to the center. Turn the sector shaft adjusting screw in a clockwise direction backward until the backlash occurs, and then turn in further until the backlash is missing while an additional three fourths to half turn is usually made before tightening the locknut. At last, reconnect the relay rod balljoint and turn off the engine.

OEM Dodge Steering Gear Box

Power Steering Gear Box

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

178 Steering Gear Boxes found

View related parts
Dodge Power Steering Pump Part Number: 68170214AB
$999.75 MSRP: $1525.00
You Save: $525.25 (35%)
ADD TO CART
Product Specifications
- Other Name: Gear Kit - Power Steering; Steering Gear Box; Steering Gearbox; Steering Gear; Gear Assembly
- Replaces: 52106835AE, 68090633AA, 68170214AA, 52106835AC, 52106835AG, 52106835AF, RL106835AG
Fits the following Dodge Models:
- Ram 2500 | 2003-2008 | Laramie, SLT, ST, SXT, Sport, TRX4 | 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
- Ram 3500 | 2003-2008 | Laramie, SLT, ST, SXT, Sport, TRX4 | 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS
View related parts
Dodge Steering Gear Part Number: 5154519AC
$792.76 MSRP: $1220.00
You Save: $427.24 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 5105085AE, 5105085AF, 5105085AD, 5154519AB, 5105085AG, 68060088AB, 68060088AC, 5154519AA, 5105085AC
Fits the following Dodge Models:
- Caliber | 2007-2010 | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Steering Gear Part Number: 68244586AB
$2559.65 MSRP: $3865.00
You Save: $1305.35 (34%)
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
Fits the following Dodge Models:
- Challenger | 2015-2018 | SRT Demon, SRT Hellcat, SRT Hellcat Widebody | 8 Cyl 6.2 L GAS
View related parts
Dodge Steering Gear Part Number: 4584569AF
$806.02 MSRP: $1220.00
You Save: $413.98 (34%)
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Rack & Pinion; Gear Assembly; Gear Rack And Pinion Complete Assembly Including Tie Rod Ends; Gear Rack And Pinion
- Replaces: 4584569AE
Fits the following Dodge Models:
- Challenger | 2010-2014 | R/T, R/T Classic, Rallye Redline, SE, SXT, SXT Plus | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
- Charger | 2011-2014 | R/T, SE, SRT8, SXT, SXT Plus | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Steering Gear Part Number: 68575536AA
$1262.29 MSRP: $1815.00
You Save: $552.71 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Power Steering; Steering Gear Box; Steering Gearbox; Gear Assembly
- Replaces: 5154349AB, R2122316AG, 68210720AB, 68210720AA, 68210720AC
Fits the following Dodge Models:
- Ram 2500 | 2009-2010 | Laramie, Power Wagon, SLT, ST, SXT, TRX | 5.7L V8, 5.9L L6, 6.7L L6, 8 Cyl 5.7 L GAS
- Ram 3500 | 2009-2010 | 5.7L V8, 5.9L L6, 6.7L L6
View related parts
Dodge Gear Assembly Part Number: 68593997AA
$2349.70 MSRP: $3565.00
You Save: $1215.30 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion
- Replaces: 68526090AB
Fits the following Dodge Models:
- Challenger | 2023 | GT, SXT | 6 Cyl 3.6 L GAS
View related parts
Dodge Steering Gear Part Number: 5151705AF
$1092.21 MSRP: $1650.00
You Save: $557.79 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 5151705AD, 5151790AD, 5151790AC, RL151705AD, 5151790AB, 5151705AB, 5151705AE, 5151705AC
Fits the following Dodge Models:
- Grand Caravan | 2011-2020 | American Value Package, C/V, Crew, Express, GT, Mainstreet, R/T, SE, SE 30th Anniversary Edition, SE Plus, SXT, SXT 30th Anniversary Edition | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Steering Gear Part Number: 68594293AB
$1112.10 MSRP: $1685.00
You Save: $572.90 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rack - Rack And Pinion; Gear Assembly
- Replaces: 68524909AC
Fits the following Dodge Models:
- Durango | 2023-2025 | Citadel, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, Special Service | 8 Cyl 5.7 L GAS
View related parts
Dodge Steering Gear Part Number: 68140631AE
$650.21 MSRP: $985.00
You Save: $334.79 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 5151348AF, 5151348AE, 68140627AB, 68140631AC, 68140631AD, RL140627AC, R8140631AD, 68140627AA, 68140631AA, 68140631AB, 68140627AC
Fits the following Dodge Models:
- Journey | 2011-2020 | AVP, Crew, Crossroad, Express, GT, Limited, Lux, Mainstreet, R/T, SE, SE Value, SXT | 2.4L L4, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Steering Gear Part Number: 55366385AL
$520.28 MSRP: $1190.00
You Save: $669.72 (57%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Gear Assembly
- Replaces: 55366385AK, 55366385AG, 55366385AE, 55366385AI, 55366385AD, 55366385AF, 55366385AJ
Fits the following Dodge Models:
- Ram 1500 | 2006-2008 | Laramie, SLT, SRT-10, ST, Sport, TRX4 | 10 Cyl 8.3 L GAS, 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8.3L V10
View related parts
Dodge Steering Gear Part Number: 68594294AB
$2084.50 MSRP: $3150.00
You Save: $1065.50 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rack - Rack And Pinion; Gear Assembly
- Replaces: 68524910AC
Fits the following Dodge Models:
- Durango | 2022-2025 | Citadel, GT, GT Plus, GT Premium, Pursuit, SXT, SXT Plus | 6 Cyl 3.6 L GAS
View related parts
Dodge Steering Gear Part Number: 5154515AC
$639.16 MSRP: $968.00
You Save: $328.84 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 5154515AB, 5105528AJ, 5154515AA, RL105528AJ
Fits the following Dodge Models:
- Caliber | 2012 | SE, SXT, SXT Plus | 2.0L L4, 2.4L L4, 4 Cyl 2.0 L GAS
View related parts
Dodge Gear Assembly Part Number: 68526096AA
$633.62 MSRP: $932.00
You Save: $298.38 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion
- Replaces: 68466323AA, 68466323AC, 68466323AB, 68418398AD, 68418398AE
Fits the following Dodge Models:
- Challenger | 2016-2023 | GT, R/T, R/T Plus, R/T Plus Shaker, R/T Shaker, SXT, SXT Plus, T/A | 3.6L V6, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
- Charger | 2019-2023 | GT, Pursuit, SXT | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Steering Gear Part Number: 5154513AC
$866.79 MSRP: $1320.00
You Save: $453.21 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 5154513AA, 5154513AB, RL154513AA
Fits the following Dodge Models:
- Durango | 2011-2015 | Citadel, Crew, Express, Heat, Limited, Rallye, SXT, Special Service | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Steering Gear Part Number: 4584571AD
$1244.70 MSRP: $1880.00
You Save: $635.30 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion Complete Assembly Including Tie Rod Ends; Gear Rack And Pinion
- Replaces: 4584571AC, 4584571AA, 4584571AB
Fits the following Dodge Models:
- Challenger | 2011-2014 | SRT8 | 6.4L V8, 8 Cyl 6.4 L GAS
- Charger | 2011-2019 | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Road & Track, R/T Scat Pack, SE, SRT 392, SRT Hellcat, SRT8, SXT, SXT Plus, SXT Plus Leather, Scat Pack | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Steering Gear Part Number: MR510120
Product Specifications
- Other Name: Gear - Power Steering; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Power Steering
Fits the following Dodge Models:
- Stratus | 2001-2005 | R/T, SE | 6 Cyl 3.0 L GAS
View related parts
Dodge Gear Assembly, Front Part Number: 68526095AA
$641.63 MSRP: $947.00
You Save: $305.37 (33%)
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly, Front
- Position: Front
- Replaces: 68323546AC, 68323546AD, 68417472AB, 68274996AB, 68323546AA, 68417472AD, 68466322AB, 68323546AB, 68417472AA, 68417472AC, 68466322AA
Fits the following Dodge Models:
- Charger | 2016-2023 | Daytona, Daytona 392, GT, GT Plus, Pursuit, R/T, R/T 392, R/T Scat Pack, SRT 392, SXT, SXT Plus, SXT Plus Leather, Scat Pack | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Steering Gear Part Number: 68140628AE
$1099.63 MSRP: $1625.00
You Save: $525.37 (33%)
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 68140628AA, 68140628AC, 68140628AB, 68140628AD, RL140628AC
Fits the following Dodge Models:
- Journey | 2011-2020 | AVP, Crew, Crossroad, GT, Limited, R/T, SE, SE Value, SXT | 2.4L L4, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Dodge Steering Gear Part Number: 52109984AH
$615.30 MSRP: $899.00
You Save: $283.70 (32%)
Product Specifications
- Other Name: Gear - Rack And Pinion; Rack and Pinion Assembly; Steering Gearbox; Gear Assembly; Gear Rack And Pinion
- Replaces: 52109984AE, 52109984AG, 52109984AF
Fits the following Dodge Models:
- Nitro | 2007-2011 | Detonator, Heat, R/T, SE, SLT, SXT, Shock | 3.7L V6, 4.0L V6, 6 Cyl 3.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Dodge Gear Assembly Part Number: 5154518AB
$617.59 MSRP: $899.00
You Save: $281.41 (32%)
Product Specifications
- Other Name: Gear - Rack And Pinion; Steering Gearbox
- Replaces: 5154518AA, 5154518AC
Fits the following Dodge Models:
- Caliber | 2012 | SE, SXT, SXT Plus | 4 Cyl 2.0 L GAS

| Page 1 of 9 |Next >

1-20 of 178 Results

Dodge Steering Gear Box

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Steering Gear Box for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Steering Gear Box converts turns of the wheel of the driver into accurate road direction with firm low-play control. Dodge began as a tough machine shop and retained that hard edge when it unleashed the first all-steel body car in 1914, which proved to be brute tough and yet still could look good in the city streets. Dodge created muscle machines that pushed HEMI power beneath the bonnet and allowed common people to morph like weekend racers without emptying wallets or spoiling delicate components. The Viper program followed by the boisterous Fratzonic Chambered Exhaust upped the excitement level to electric rides by pumping 600 watts of roar into the air in seconds, and the chambered exhaust switches between being a stealthy hush and a drag-strip blast in a few seconds. This rebel attitude is transferred to sedans, coupes, and SUVs, and thus, whether it is kids or lap times, the badge reminds the driver of powerful acceleration and the unwillingness to behave in a courteous way. Steering Gear Box converts steering wheel rotation to lateral motion in a recirculating ball steering gear system that cuts friction and removes play in steering wheels as well as gives confident road feedback as opposed to wobbly uncertainty even after thousands of hard miles. Tied to hydraulic assist, the Steering Gear Box reduces the effort required in the parking lot to as light as fingertips with the heavy highway heft that leaves the same on-center feel across decades of chassis designs. Designed seals and improved bearings in the Steering Gear Box prevent leakage and endure hard wear, keeping the same light-in-center feel consistent across generations of Dodge chassis designs.

Dodge Steering Gear Box Parts and Q&A

Steering Gear
R2007280
Q: How to adjust Steering Gear Box on Dodge Ramcharger?
A:
Some sagging can be corrected by manual turning of the inner and outer rods even without the removal of the steering gear. For change of the worm bearing preload, you have to remove the Pitman arm from the sector shaft through the use of puller after removing the nut and the thrust washer. The horn pad has to be pulled off from the steering wheel Attachment 170 detects that the sector shaft screw locknut has to be unlocked and the screw has to be turned back by two turns at least. Twist the wheel by 720 degrees counter clockwise if right hand steered vehicle and vice versa, then using a socket on the steering wheel nut fasten a torque wrench to the steering shaft and rotate it back to the straight position while holding the torque steady to the prescribed limit. In case the torque wrench cannot be used, the spring balance could be used provided it is mounted one inch from the centre point of the socket wrench. In order to increase the worm bearing preload rotate the worm bearing adjuster in a clockwise direction and release the worm bearing preload locknut and then lock it when done. For sector gear adjustment turn the steering wheel to the left and then to the right as far as it can be turned, count the turns and then turn back half a turn. Tighten the sector shaft screw and lead screw until all the clearence between ball nut rack and corresponding teeth of sector gear have been eliminated and then tighten the lock nut. Check and turn the steering wheel a quarter turn from center and apply the measured force to return the steering wheel back to the center, should be within limits, adjust if necessary. Only when these adjustments have been made correctly, align the wheels and steering wheel, before fitting the Pitman arm on. For power steering sector shaft adjustment, the relay rod ball joint taper pin should be disconnected from the Pitman arm, the engine should be switched on and the same should be allowed to run on the idle condition. With the wheel in the straight-ahead position spin it from side to side through 10 smaller turns and back to the center. Turn the sector shaft adjusting screw in a clockwise direction backward until the backlash occurs, and then turn in further until the backlash is missing while an additional three fourths to half turn is usually made before tightening the locknut. At last, reconnect the relay rod balljoint and turn off the engine.