How to Remove and Reinstall the ABS Control Module for Antilock Brakes on Dodge Stratus?

First, remove the remote ground cable from the strut tower on the left, then make sure it can't touch anything by using a ground cable insulator. Use the brake pedal positioning tool to push down the pedal slightly further than an inch, so that the master cylinder doesn't connect to the hydraulic system. After that, take away the ICU's air cleaner housing and clean any dust from the fittings on top of the ICU. Remove the brake tubes from the main and secondary master cylinder ports at the ICU and then from the four chassis brake tubes across the top of the junction block. Pull the lock on the 24-way connector, located in the CAB, upwards to disconnect it. Take out the three bolts keeping the ICU fixed to its mounting bracket and pull the ICU out of the car. Slide the ICU into the mounting bracket, then fix it with isolators, washers and fasten the three HCU mounting bolts to 11 Nm (97 inch lbs.). Install the seal into the 24-way connector first and then push and lock it in the CAB socket. The four chassis brake tubes on the top of the ICU should be connected and tightened with a crow foot wrench to 17 Nm (145 inch lbs.), followed by the primary and secondary master cylinder ports, each tightened to the same amount. Set the air cleaner housing in place, remove your brake pedal, link the remote ground cable to the left shock tower's ground stud, drain and recharge the brake and ABS hydraulic system and drive the car to see if both work correctly.

How to Service and Repair an ABS Control Module on Dodge Stratus?

Before you start service or repair of the Controller Antilock Brake, disconnect the negative cable on the battery and lift the vehicle. Raise the connector lock of the CAB to pull out the 24-way connector and the other connector for the pump/motor. Unbolt the ICU's bracket from the lower radiator support and while doing this, make sure the brake lines aren't bent. Loosen and take out all screws connecting the CAB to the HCU half of the ICU, then remove the CAB. When installing, make sure the CAB is fastened to the half of the ICU nearest the HCU with screws and tighten them to 2 Nm (17 in. lbs.). Screw the ICU mounting bracket back onto the lower radiator support and tighten the bolts with 28 Nm (21 ft. lbs.) of torque. Attach the connectors for the 24-way electrical and the pump/motor, lift the car and then put back the negative battery wire. Attach the DRB III to your vehicle and start the activating process.

OEM Dodge Stratus ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 ABS Control Modules found

View related parts
Dodge Stratus Control Module Part Number: 5093774AA
$518.60 MSRP: $744.00
You Save: $225.40 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Control - Anti-Lock Brake; ABS Control Module; ABS Control Unit; Control Unit Anti-Lock Brake
- Replaces: 5080634AA, 5093740AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Modulator Valve Part Number: 5142283AA
Product Specifications
- Other Name: HCU - ABS; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2006 Dodge Stratus | R/T, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Modulator Valve Part Number: MR370625
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Control Module Part Number: MR370624
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Hydraulic Assembly; Modulator Valve; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Control Module Part Number: 5159191AB
Product Specifications
- Other Name: Control - Anti-Lock Brakes; ABS Control Module; ABS Control Unit; Module Anti-Lock Brakes
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Stratus | R/T, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Control Module Part Number: 5159191AA
Product Specifications
- Other Name: Control - Anti-Lock Brakes; ABS Control Module; ABS Control Unit; Module Anti-Lock Brakes
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Stratus | R/T, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus ABS Control Unit Part Number: 5102526AA
Product Specifications
- Other Name: Accumulator - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Control Module; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Stratus | ES, R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Control Module Part Number: 5102525AA
Product Specifications
- Other Name: Control - Anti-Lock Brake; ABS Control Module; ABS Control Unit; Control Unit Anti-Lock Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Stratus | ES, R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Modulator Valve Part Number: 5018254AA
Product Specifications
- Other Name: Accumulator - Anti-Lock Brake System; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2004 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Modulator Valve Part Number: 4897779AA
Product Specifications
- Other Name: Master Cylinder - Anti-Lock Brake System; ABS Control Module; ABS Control Unit; Modulator; Hydraulic Control Unit Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Control Module Part Number: 4602249AC
Product Specifications
- Other Name: Module - Anti-Lock Brake System; ABS Control Module; ABS Control Unit; Module Anti-Lock Brake System
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Control Module Part Number: R4605094
Product Specifications
- Other Name: Module - ABS; ABS Control Module; Module, TCM, Eatx, 41Te Transmission; Module, W/Bracket, A.B.S. Controller; Module Anti-Lock Brakes
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Dodge Stratus | Base, ES | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS

Dodge Stratus ABS Control Module

Choose OEM ABS Control Module that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each ABS Control Module follows strict manufacturing steps to lock in quality and fit. If your Dodge Stratus matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Stratus parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Stratus ABS Control Module is big and very important part on the Dodge Stratus that highly improves its reliability as well as performance because it provide secure touching of the brake pedal in any driving situations. This particular module is used to arrest the wheels from locking during hard braking maneuvers and integrally interact with ABS modulator to provide the required tractive adhesion with the road and avoid skidding. The Dodge Stratus ABS Control Module contains features like wheel speed sensors, valves, a pump, and a controller (ECU), which work together in controlling the pressure of the brake and alter the stagnation force of the brake strength by inputting new data from the sensors. This functionality makes the problematic area evident in improving efficiency as well as safety, making the Dodge Stratus a favourable car for drivers. I have designed this compatible ABS Control Module to work well with the Stratus models that were manufactured between the years 1995 to 2005, the car's engine type may be 2.0 L I4 or 2.7 L V6. Also, editions of the ABS Control Module could include elements such as ESC and traction control, which only improves the safety of the Dodge Stratus. The Dodge Stratus ABS Control Module is unique among the available options in the automotive market due to its solidity and focus on performance, as well as its significance in the braking system and impact on the car's driving capabilities.

Dodge Stratus ABS Control Module Parts and Q&A

Modulator Valve
5142283AA
Q: How to Remove and Reinstall the ABS Control Module for Antilock Brakes on Dodge Stratus?
A:
First, remove the remote ground cable from the strut tower on the left, then make sure it can't touch anything by using a ground cable insulator. Use the brake pedal positioning tool to push down the pedal slightly further than an inch, so that the master cylinder doesn't connect to the hydraulic system. After that, take away the ICU's air cleaner housing and clean any dust from the fittings on top of the ICU. Remove the brake tubes from the main and secondary master cylinder ports at the ICU and then from the four chassis brake tubes across the top of the junction block. Pull the lock on the 24-way connector, located in the CAB, upwards to disconnect it. Take out the three bolts keeping the ICU fixed to its mounting bracket and pull the ICU out of the car. Slide the ICU into the mounting bracket, then fix it with isolators, washers and fasten the three HCU mounting bolts to 11 Nm (97 inch lbs.). Install the seal into the 24-way connector first and then push and lock it in the CAB socket. The four chassis brake tubes on the top of the ICU should be connected and tightened with a crow foot wrench to 17 Nm (145 inch lbs.), followed by the primary and secondary master cylinder ports, each tightened to the same amount. Set the air cleaner housing in place, remove your brake pedal, link the remote ground cable to the left shock tower's ground stud, drain and recharge the brake and ABS hydraulic system and drive the car to see if both work correctly.
Control Module
5093774AA
Q: How to Service and Repair an ABS Control Module on Dodge Stratus?
A:
Before you start service or repair of the Controller Antilock Brake, disconnect the negative cable on the battery and lift the vehicle. Raise the connector lock of the CAB to pull out the 24-way connector and the other connector for the pump/motor. Unbolt the ICU's bracket from the lower Radiator Support and while doing this, make sure the brake lines aren't bent. Loosen and take out all screws connecting the CAB to the HCU half of the ICU, then remove the CAB. When installing, make sure the CAB is fastened to the half of the ICU nearest the HCU with screws and tighten them to 2 Nm (17 in. lbs.). Screw the ICU mounting bracket back onto the lower radiator support and tighten the bolts with 28 Nm (21 ft. lbs.) of torque. Attach the connectors for the 24-way electrical and the pump/motor, lift the car and then put back the negative battery wire. Attach the DRB III to your vehicle and start the activating process.