How to Bleed a Brake Master Cylinder on Dodge Stratus?

For bleeding the brake master cylinder, clamp it down in a vise and attach Bleeding Tubes 6802 to both outlet ports, so they remain below the top of the brake fluid in the reservoir. Use fluid that matches DOT 3 standards such as Mopar, to fill the brake fluid reservoir. Insert a wooden dowel into the bleed screws and slowly depress the push rod as the pistons return to the normal position, continue until you no longer see air bubbles escaping from the bleed tubes. When it's done bleeding, remove the tubes from the outlet ports, plug the ports and set the fill cap onto the reservoir before you ease the brake master cylinder out of the vise. It's fine to not worry about bleeding the entire hydraulic setup after the brake master cylinder is changed, but the brake master cylinder in the vacuum booster needs to be properly bled and filled when it is installed.

How to Service and Repair a Brake Master Cylinder on Dodge Stratus?

You should start the brake master cylinder servicing and repairs by unplugging the harness connector from the brake fluid level switch inside the brake master cylinder reservoir. After that, unhook the brake tubes from the brake master cylinder outlet ports and insert plugs onto the open brake tube outlets of the brake master cylinder. You should wash the space between the brake master cylinder and the booster with Mopar(R) Brake Parts Cleaner or another similar item. Unfasten the two nuts securing the brake master cylinder to the vacuum booster and pull the brake master cylinder straight off its bolts. When installing, set the brake master cylinder assembly over the studs on the brake power unit and make certain that the push rod on the power brake vacuum booster is lined up with the piston on the brake master cylinder. Position the two mounting nuts and tighten them so that there are 26 Nm (230 inch lbs.) of torque. Pull the ends of the brake tubes around the brake master cylinder's primary and secondary ports and secure them tightly, giving them a total torque of 17 Nm (145 inch lbs.). Attach the wiring harness connector to the brake fluid level switch, add clean, fresh Mopar(R) Brake Fluid or an equivalent to the brake master cylinder and go for a drive to check the brakes.

OEM Dodge Stratus Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Brake Master Cylinders found

View related parts
Dodge Stratus Master Cylinder Part Number: 4764192
$159.25 MSRP: $229.00
You Save: $69.75 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Overhaul Kit Part Number: MR493695
Product Specifications
- Other Name: Wheel Cylinder - Brake Master; Cylinder Brake Master
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2005 Dodge Stratus | R/T | 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Overhaul Kit Part Number: MR493691
Product Specifications
- Other Name: Wheel Cylinder - Brake Master; Cylinder Brake Master
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2004 Dodge Stratus | R/T | 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Overhaul Kit Part Number: MR493681
Product Specifications
- Other Name: Wheel Cylinder - Brake Master; Cylinder Brake Master
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2005 Dodge Stratus | R/T | 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: MR475973
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: MR475432
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: MR475431
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Dodge Stratus | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Reservoir Part Number: MR449411
Product Specifications
- Other Name: Master Cylinder - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2005 Dodge Stratus | R/T | 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: 5101794AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Dodge Stratus | ES, R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: 5019401AA
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Reservoir Tank Part Number: 5019400AA
Product Specifications
- Other Name: Master Cylinder - Brake Master Cylinder; Brake Master Cylinder Reservoir; Reservoir; Reservoir Brake Master Cylinder
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Dodge Stratus | ES, R/T, SE, SE Plus, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: 4764194
Product Specifications
- Other Name: Master Cylinder - Brake; Brake Master Cylinder; Master Cylinder Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Dodge Stratus | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Stratus Master Cylinder Part Number: 4764103
Product Specifications
- Other Name: Master Cylinder Brake; Brake Master Cylinder; Master Cylinder, Power Disc Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Dodge Stratus | Base, ES | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS

Dodge Stratus Brake Master Cylinder

Choose OEM Brake Master Cylinder that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Master Cylinder follows strict manufacturing steps to lock in quality and fit. If your Dodge Stratus matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Stratus parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Stratus Brake Master Cylinder is the part of the current braking system; it is one of the most reliable and focused parts in various models of Dodge Stratus manufactured till 2005. This Brake Master Cylinder effectively transmits foot feeler action to hydraulic pressure for the effective control over the vehicle's braking asset. Dodge Stratus Brake Master Cylinder also has two pistons providing that even if there is a hydraulic failure, it is still possible to stop the vehicle safely provided circuit is functioning and this is a factor that increases on the overall safety. It is also required to perform periodic inspections of the Brake Master Cylinder since its problems, such as leaks, rust, and others that might occur, can eventually affect the braking system. Dodge Stratus is a sedan and coupe that is powered by potent motors compatible with the Brake Master Cylinder to deliver responsiveness in acceleration with admirable fuel economy. The fact that the Brake Master Cylinder directly controls the calipers or drum brakes more likely adds to the Stratus's generally good reputation for its solid stopping power. Further, the spontaneity attribute is both performance and safety enhanced due to the fact that the Dodge Stratus Brake Master Cylinder, is built and designed to offer a lot of performance. Thus, facilitating proper displacement of hydraulic fluid, this Brake Master Cylinder contributes to the improvement of the Dodge Stratus's performance and safety and become indispensable for drivers who value reliability of their automobiles.

Dodge Stratus Brake Master Cylinder Parts and Q&A

Master Cylinder
4764192
Q: How to Bleed a Brake Master Cylinder on Dodge Stratus?
A:
For bleeding the brake master cylinder, clamp it down in a vise and attach Bleeding Tubes 6802 to both outlet ports, so they remain below the top of the brake fluid in the reservoir. Use fluid that matches DOT 3 standards such as Mopar, to fill the brake fluid reservoir. Insert a wooden dowel into the bleed screws and slowly depress the push rod as the Pistons return to the normal position, continue until you no longer see air bubbles escaping from the bleed tubes. When it's done bleeding, remove the tubes from the outlet ports, plug the ports and set the fill cap onto the reservoir before you ease the brake master cylinder out of the vise. It's fine to not worry about bleeding the entire hydraulic setup after the brake master cylinder is changed, but the brake master cylinder in the vacuum booster needs to be properly bled and filled when it is installed.
Master Cylinder
MR475432
Q: How to Service and Repair a Brake Master Cylinder on Dodge Stratus?
A:
You should start the brake master cylinder servicing and repairs by unplugging the harness connector from the brake fluid level switch inside the brake master cylinder reservoir. After that, unhook the brake tubes from the brake master cylinder outlet ports and insert plugs onto the open brake tube outlets of the brake master cylinder. You should wash the space between the brake master cylinder and the booster with Mopar(R) Brake Parts Cleaner or another similar item. Unfasten the two nuts securing the brake master cylinder to the vacuum booster and pull the brake master cylinder straight off its bolts. When installing, set the brake master cylinder assembly over the studs on the brake power unit and make certain that the push rod on the power brake vacuum booster is lined up with the Piston on the brake master cylinder. Position the two mounting nuts and tighten them so that there are 26 Nm (230 inch lbs.) of torque. Pull the ends of the brake tubes around the brake master cylinder's primary and secondary ports and secure them tightly, giving them a total torque of 17 Nm (145 inch lbs.). Attach the wiring harness connector to the brake fluid level switch, add clean, fresh Mopar(R) Brake Fluid or an equivalent to the brake master cylinder and go for a drive to check the brakes.