How to Install the Air Bag Control Module While Ensuring the Supplemental Restraint System is Disabled on Jeep Commander?

Disable the SRS before installing the Occupant Restraint Controller so the air bag isn't activated accidentally, unplug and isolate the battery negative cable and let the capacitor empty for two minutes. Press the housing onto its mount on the transmission tunnel, so that the base is cleared and the arrow is pointing in the right direction. Tighten the three screws that secure the ORC to 14 Nm (10 ft. lbs.) while installing them. Join the instrument panel and body wire harness connectors to the ORC connector ends, making sure the latches and red CPA locks are secure. Fit the center console into the open slot in the floor panel transmission tunnel. Leave the negative battery cable disconnected until the SRS test procedures after SRS component servicing have finished.

How to Maintain the Air Bag Control Module on Jeep Commander?

Make sure the Air Bag Control Module is disabled before service by discharging the system's capacitor. For this, disconnect and isolate the battery negative cable and let the capacitor sit for two minutes before proceeding. You should never strike or drop the occupant restraint controller; the impact sensor may be damaged and will need to be replaced. Open by removing the center console from the transmission tunnel located at the top of the floor. After that, unplug the instrument panel and body wiring plugs from the Occupant Restraint Controller receptacles on the front-facing side of the module. To separate, press the lock forward, then depress the side nearest to the ORC, release the latch and pull the connector straight back. After that, remove the three screws attached to the ORC mount welded to the floor panel transmission tunnel and lift the ORC out of the mount.

OEM Jeep Commander Air Bag Control Module

SRS Airbag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Air Bag Control Modules found

View related parts
Jeep Commander Control Module, Passenger Side Part Number: 56043195AZ
$374.94 MSRP: $548.00
You Save: $173.06 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Passenger Presence Module, Right; SDM Module; Diagnostic Module; Passenger Sensor; Occupant Module; Module; Module Occupant Classification
- Position: Passenger Side
- Replaces: 56043195AX, 56043195AS, 56043195AR, 56043195AT, 56043195AP
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Jeep Commander | 65th Anniversary Edition, Base, Limited, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Diagnostic Module Part Number: 68000233AD
$299.11 MSRP: $445.00
You Save: $145.89 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module; Occupant Module; Module Occupant Restraint
- Replaces: 68000233AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Jeep Commander | Base, Limited, Overland, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Diagnostic Module, Passenger Side Part Number: 5183712AA
$265.63 MSRP: $336.73
You Save: $71.10 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Passenger Presence Module, Right; Occupant Module; Module Occupant Classification
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Jeep Commander | Base, Limited, Overland, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Diagnostic Module Part Number: 56038801AD
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Occupant Module; Module Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Jeep Commander | 65th Anniversary Edition, Base, Limited, Overland, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Control Module, Passenger Side Part Number: 56043195BD
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Passenger Presence Module, Right; Occupant Module; Module Occupant Classification
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Jeep Commander | Base, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Jeep Commander Diagnostic Module, Passenger Side Part Number: 56054060AC
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module, Right; Occupant Module; Module Occupant Restraint
- Position: Passenger Side
- Replaces: 56054060AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Jeep Commander | Limited, Overland, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Commander Diagnostic Module Part Number: 4896119AF
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Occupant Module; Module Occupant Restraint
- Replaces: 4896119AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Jeep Commander | Limited, Overland, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS

Jeep Commander Air Bag Control Module

Choose OEM Air Bag Control Module that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Air Bag Control Module follows strict manufacturing steps to lock in quality and fit. If your Jeep Commander matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Commander parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Commander Air Bag Control Module Parts and Q&A

Diagnostic Module, Passenger Side
56054060AC
Q: How to Install the Air Bag Control Module While Ensuring the Supplemental Restraint System is Disabled on Jeep Commander?
A:
Disable the SRS before installing the Occupant Restraint Controller so the air bag isn't activated accidentally, unplug and isolate the battery negative cable and let the capacitor empty for two minutes. Press the housing onto its mount on the transmission tunnel, so that the base is cleared and the arrow is pointing in the right direction. Tighten the three screws that secure the ORC to 14 Nm (10 ft. lbs.) while installing them. Join the instrument panel and body wire harness connectors to the ORC connector ends, making sure the latches and red CPA locks are secure. Fit the center console into the open slot in the floor panel transmission tunnel. Leave the negative Battery Cable disconnected until the SRS test procedures after SRS component servicing have finished.
Control Module, Passenger Side
56043195AZ
Q: How to Maintain the Air Bag Control Module on Jeep Commander?
A:
Make sure the Air Bag Control Module is disabled before service by discharging the system's capacitor. For this, disconnect and isolate the battery negative cable and let the capacitor sit for two minutes before proceeding. You should never strike or drop the occupant restraint controller; the impact sensor may be damaged and will need to be replaced. Open by removing the center console from the transmission tunnel located at the top of the floor. After that, unplug the instrument panel and body wiring plugs from the Occupant Restraint Controller receptacles on the front-facing side of the module. To separate, press the lock forward, then depress the side nearest to the ORC, release the latch and pull the connector straight back. After that, remove the three screws attached to the ORC mount welded to the floor panel transmission tunnel and lift the ORC out of the mount.