How to replace a Blend Door Actuator on 2001 Chrysler Sebring?

You should remove the negative battery cable for 60 seconds before you remove the blend door actuator, to allow the software calibration process to begin. First, disconnect the negative battery cable; after that, remove the floor console, rear heat ducts and HVAC housing. Now, uncouple the electrical cable from the actuator and after unscrewing the attaching screws, pull straight down on the actuator and keep track of its shaft location to help with installation. Set up the blend door actuator so the shaft spline connects correctly with the cam, before fixing the actuator in place. Attach the wire harness connector to the actuator, put the HVAC housing, rear heat ducts and floor console back into place and then attach the negative battery cable.

OEM 2001 Chrysler Sebring Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Blend Door Actuators found

View related parts
2001 Chrysler Sebring Door Actuator Part Number: 4885206AB
$137.09 MSRP: $202.00
You Save: $64.91 (33%)
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Servo; A/C and Heater Actuator with Bracket, Lever, and Recirculation Door.
- Item Weight: 0.70 Pounds
- Item Dimensions: 1.9 x 3.6 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4885206AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Actuator Part Number: 4885457AC
Product Specifications
- Other Name: Actuator - Mode Control; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator Mode Control
- Item Weight: 0.70 Pounds
- Item Dimensions: 4.4 x 3.7 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4885457AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
2001 Chrysler Sebring Actuator Part Number: 4885207AB
Product Specifications
- Other Name: Actuator - Blend Door; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator; Actuator Blend Door
- Item Weight: 0.70 Pounds
- Item Dimensions: 5.1 x 3.8 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4885207AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Chrysler Sebring Submodels:
- Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS

2001 Chrysler Sebring Blend Door Actuator Parts and Q&A

Q: How to replace a Blend Door Actuator on 2001 Chrysler Sebring?
A: You should remove the negative battery cable for 60 seconds before you remove the blend door actuator, to allow the software calibration process to begin. First, disconnect the negative battery cable; after that, remove the floor console, rear heat ducts and HVAC housing. Now, uncouple the electrical cable from the actuator and after unscrewing the attaching screws, pull straight down on the actuator and keep track of its shaft location to help with installation. Set up the blend door actuator so the shaft spline connects correctly with the cam, before fixing the actuator in place. Attach the wire harness connector to the actuator, put the HVAC housing, rear heat ducts and floor console back into place and then attach the negative battery cable.