How to service and repair a control arm on 2001 Dodge Ram 3500?

For services and repairs of the upper control arm, lift the car and place supports, then take off the wheel and tire assembly. Lift and support the lower arm near the edge of the car with a jack stand. After that, take out the nut and cotter pin on the upper ball joint and part MB-990635 to release the ball joint from the knuckle. Pull the bolts holding the pivot bar to the upper suspension arm and then remove the arm from beneath the vehicle. Put the upper arm on the bracket and fasten the two pivot bar bolts to 169 Nm (125 ft. lbs.). Install the ball joint in the knuckle, bolt it there with the nut tightened to 81 Nm (60 ft. lbs.) and then pin it back in place with the cotter. Release the jack from the suspension arm, add the wheel and tire back to the car, cast it aside and lower your vehicle. The last step is to square up the rubber bushings in the front suspension.

OEM 2001 Dodge Ram 3500 Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Control Arms found

View related parts
2001 Dodge Ram 3500 Upper Control Arm Part Number: 52106799AA
$170.42 MSRP: $216.04
You Save: $45.62 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Control; Suspension Control Arm; Control Arm; Upper Arm; Arm Control
- Item Weight: 5.40 Pounds
- Item Dimensions: 2.4 x 2.9 x 20.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106799AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Ram 3500 Submodels:
- Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
2001 Dodge Ram 3500 Lower Control Arm Part Number: 52113678AA
Product Specifications
- Other Name: Arm - Lower Control; Suspension Control Arm and Ball Joint Assembly; Control Arm Assembly; Control Arm; Arm Lower Control Front
- Position: Lower
- Item Weight: 32.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52113678AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Ram 3500 Submodels:
- Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
2001 Dodge Ram 3500 Lower Control Arm Part Number: 52106778AA
Product Specifications
- Other Name: Arm - Control; Suspension Control Arm; Control Arm; Lower Arm; Arm Control
- Item Weight: 6.50 Pounds
- Item Dimensions: 2.7 x 3.4 x 23.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52106778AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Ram 3500 Submodels:
- Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
View related parts
2001 Dodge Ram 3500 Upper Control Arm Part Number: 52106678AA
Product Specifications
- Other Name: Arm - Upper Control; Suspension Control Arm and Ball Joint Assembly.; Arm Upper Control Front
- Position: Upper
- Item Weight: 11.70 Pounds
- Item Dimensions: 16.9 x 15.0 x 10.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 52106678AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Ram 3500 Submodels:
- Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS

2001 Dodge Ram 3500 Control Arm Parts and Q&A

Q: How to service and repair a control arm on 2001 Dodge Ram 3500?
A: For services and repairs of the upper control arm, lift the car and place supports, then take off the wheel and tire assembly. Lift and support the lower arm near the edge of the car with a jack stand. After that, take out the nut and cotter pin on the upper ball joint and part MB-990635 to release the ball joint from the knuckle. Pull the bolts holding the pivot bar to the upper suspension arm and then remove the arm from beneath the vehicle. Put the upper arm on the bracket and fasten the two pivot bar bolts to 169 Nm (125 ft. lbs.). Install the ball joint in the knuckle, bolt it there with the nut tightened to 81 Nm (60 ft. lbs.) and then pin it back in place with the cotter. Release the jack from the suspension arm, add the wheel and tire back to the car, cast it aside and lower your vehicle. The last step is to square up the rubber bushings in the front suspension.