How to Install a Rear Door Window Regulator on 2007 Jeep Commander?

Wire harness connector 3 should be connected to the rear window regulator motor after you have loaded the regulator up into the rear door access point. Clip the regulator into place and screw bolts 1 and 2 to hold the regulator rails to the door, tightening all this to 8.5 Nm (75 in. lbs.). First, take off the tape holding the glass shut at the top, then put the window switch into place to start the glass moving upward. Fasten the bolts on each window regulator glass clamp to 12 Nm (105 in. lbs.). The watershield and the trim panel go inside the front door last, before doing the watershield 1 installation.

OEM 2007 Jeep Commander Window Regulator

Electric Power Window Regulator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Window Regulators found

View related parts
2007 Jeep Commander Window Regulator, Front Driver Side Part Number: 55396481AE
$115.57 MSRP: $170.00
You Save: $54.43 (33%)
ADD TO CART
Product Specifications
- Other Name: Regulator - Front Door Window; Window Regulator, Front Left
- Position: Front Driver Side
- Replaces: 55396481AB, 55396481AD, 55396481AC
- Item Weight: 5.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55396481AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Commander Submodels:
- 65th Anniversary Edition, Base, Limited, Overland, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Jeep Commander Window Regulator, Rear Passenger Side Part Number: 55396482AF
Product Specifications
- Other Name: Regulator - Rear Door Window; Window Regulator, Rear Right
- Position: Rear Passenger Side
- Replaces: 55396482AB, 55396482AC, 55396482AD
- Item Weight: 4.50 Pounds
- Item Dimensions: 28.9 x 15.9 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55396482AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Commander Submodels:
- 65th Anniversary Edition, Base, Limited, Overland, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Jeep Commander Window Regulator, Front Passenger Side Part Number: 55396480AE
Product Specifications
- Other Name: Regulator - Front Door Window; Window Regulator, Front Right
- Position: Front Passenger Side
- Replaces: 55396480AD, 55396480AB, 55396480AC
- Item Weight: 5.60 Pounds
- Item Dimensions: 33.0 x 25.2 x 0.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55396480AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Commander Submodels:
- 65th Anniversary Edition, Base, Limited, Overland, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Jeep Commander Window Regulator, Rear Driver Side Part Number: 55396483AF
Product Specifications
- Other Name: Regulator - Rear Door Window; Window Regulator, Rear Left
- Position: Rear Driver Side
- Replaces: 55396483AB, 55396483AD, 55396483AC
- Item Weight: 4.10 Pounds
- Item Dimensions: 25.3 x 14.7 x 3.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55396483AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Commander Submodels:
- 65th Anniversary Edition, Base, Limited, Overland, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS

2007 Jeep Commander Window Regulator Parts and Q&A

Q: How to Install a Rear Door Window Regulator on 2007 Jeep Commander?
A: Wire harness connector 3 should be connected to the rear window regulator motor after you have loaded the regulator up into the rear door access point. Clip the regulator into place and screw bolts 1 and 2 to hold the regulator rails to the door, tightening all this to 8.5 Nm (75 in. lbs.). First, take off the tape holding the glass shut at the top, then put the window switch into place to start the glass moving upward. Fasten the bolts on each window regulator glass clamp to 12 Nm (105 in. lbs.). The watershield and the trim panel go inside the front door last, before doing the watershield 1 installation.