JeepParts
My Garage
My Account
Cart
OEM 2008 Dodge Ram 1500 Piston
Engine Pistons- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Pistons found
2008 Dodge Ram 1500 Piston Part Number: 53021539AD
Product Specifications- Other Name: Engine Piston Set; Cast Piston Set; Piston Pin And Rod Includes Items 1, 2, 3, 4; Piston Pin And Rod See Note; Piston Pin And Rod
- Item Weight: 4.20 Pounds
- Item Dimensions: 10.6 x 8.1 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 4
- SKU: 53021539AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2008 Dodge Ram 1500 Piston Part Number: 53021538AD
Product Specifications- Other Name: Engine Piston Set; Cast Piston Set; Piston Pin And Rod Includes Items 1, 2, 3, 4; Piston Pin And Rod See Note; Piston Pin And Rod
- Item Weight: 3.50 Pounds
- Item Dimensions: 10.5 x 6.3 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53021538AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2008 Dodge Ram 1500 Piston Part Number: 68031605AD
$173.35 MSRP: $255.00You Save: $81.65 (33%)Product Specifications- Other Name: Piston Pin And Rod Std
- Replaces: 68031605AB, 68031605AA, 68031605AC
- Item Weight: 2.80 Pounds
- Item Dimensions: 11.7 x 5.3 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68031605AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2008 Dodge Ram 1500 Piston Part Number: 5019316AC
Product Specifications- Replaces: 5019316AA, 5019316AB
- Item Weight: 3.30 Pounds
- Item Dimensions: 11.3 x 7.3 x 6.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5019316AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2008 Dodge Ram 1500 Piston Parts and Q&A
- Q: How to Install Piston Assemblies into the Bore on 2008 Dodge Ram 1500?A: Before you put in the piston and the connecting rod, install the piston rings into the bore. Soak the top of the piston and the ring assembly in clean engine oil, then fit a ring compressor over them to keep the rings from moving. Put the bearing in place on the connecting rod so that the bearing's hole is lined up with the rod's hole and afterwards lubricate the bearing surface using clean engine oil. Upload Special Tool 8507 connecting rod guides into the connecting rod threads. You will notice a raised "F" mark on the piston pin bore surface of each piston and this label points forward on each bank and the connecting rod oil slinger slot should be in the same position. Wash the cylinder with a degreaser, then oil it fully with motor oil. Keep turning the crankshaft so the connecting rod journal is in the middle of the cylinder bore. Then set the rod and piston in the bore and place the connecting rod guides on top of the journal. Push the piston down into the bore with a hammer handle and hold the rod on the journal as you go. Connecting Rod Bolts come from the Torque to Yield category and should always be replaced if they are taken out. Apply engine oil to the connecting rod bolts and bearings, set the connecting rod cap and bearing in place and tighten the bolts to 27 Nm (20 ft. lbs.) plus 90°. Fit in the cylinder head(s), timing chain and cover, cylinder head covers and oil pan together with gasket or windage tray. Put the correct engine oil into the crankcase until it reaches the right level and secure the battery with the negative cable.
Related 2008 Dodge Ram 1500 Parts
2008 Dodge Ram 1500 Camshaft
2008 Dodge Ram 1500 Rocker Arm
2008 Dodge Ram 1500 Crankshaft
2008 Dodge Ram 1500 Crankshaft Pulley
2008 Dodge Ram 1500 Crankshaft Timing Gear
2008 Dodge Ram 1500 Cylinder Head
2008 Dodge Ram 1500 Dipstick Tube
2008 Dodge Ram 1500 Lash Adjuster
2008 Dodge Ram 1500 Oil Filter Housing
2008 Dodge Ram 1500 Oil Pan
2008 Dodge Ram 1500 Oil Pan Gasket
2008 Dodge Ram 1500 Timing Chain Tensioner