How to remove the fuel tank on Chrysler Cirrus?

To perform this process first, it requires removing the fuel tank filler cap, so that the pressure could be released. Do fuel pressure relief procedure and remove the negative terminal from the ground stud on the left shock tower. Inside the trunk, look to the left shock tower and fold back the mat there: there is a 4-pin connector for the fuel pump wiring harness; pull this connector off. Go down along the wire to the grommet located at the lower part of the rear seat, push the grommet in the hole in the floor pan and install the wiring and the connector through it. Loosen the fuel tank drain plug while the vehicle is on the ground in a level surface, fill an approved gasoline container and place it under the fuel tank drain plug, taking into consideration the use of the funnel in order to avoid any spillage of fuel when it is being drained. Open the drain plug and let the fuel to flow from the tank and close and tighten the drain plug. Open the clamp and remove the filler neck hose from the fuel tank and leave the quick-connect fuel line of fittings connected to the fuel pump module. At the back part of the fuel tank, remove the vapor hose connection of the rollover valve. Secure the position of the fuel tank by placing a floor jack underneath it; put a piece of wood twixt the jack head and the fuel tank. Take out the fuel tank strap bolts, and straps also. For 1998 models, lower the tank slightly and disconnect the EVAP canister purge line, remove the hoses from the EVAP canister, and remove the electrical connector from the Leak Detection Pump, be sure to label the hoses and fittings for reinstallation. Lower the fuel tank a little in order to remove the rear suspension crossmember then pull the fuel tank out of the car. To remove, undo the procedures mentioned above and fasten a piece of string or wire to the fuel pump module wiring harness then run the wire through the hole at the trunk floorpan of the car. After placing the tank safely secure to the car then pull the string to expose the wiring harness and tighten the fuel tank strap bolts to the torque required.

How to remove and reinstall a fuel tank on Chrysler PT Cruiser?

In order to take out the fuel tank, the first step is to unscrew the fuel filler cap a little to release the pressure inside then releasing the system's fuel pressure. Then, bevor the metal with a piece of metal functioning as a ground then, unscrew the nut on the negative terminal of the battery and take out the cable. Lift the car to a safe working height and support it using jackstands on the rear part of the car. Place a drain pan with a capacity of not less than sixteen gallons under the drain cap, remove the fuel tank drain cap, and let the tank drain as long as necessary before replacing the cap. Pull off the vapor hose, unscrew the fuel filler neck hose clam and separate the fuel filler neck hose from the fuel inlet pipe. Put a transmission jack or floor jack in a position to the fuel tank but put a plywood on the head of the jack to avoid scratching it. Pull both of the fuel pump and leak detection electrical connectors, the EVAP line and the quick-connect fitting on the fuel supply hose. Loosen and take out the bolts that holds the fuel tank straps and then slowly dropped the fuel tank of the vehicle. For installation, the process done in the reverse way with the reminder of making sure that the fuel tank strap bolts are tightened and the engine started to look for any leaks at the fuel line connectors that were removed.

OEM Chrysler Fuel Tank

Gas Tank

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

54 Fuel Tanks found

View related parts
Chrysler Fuel Tank Part Number: 68258723AD
$1221.03 MSRP: $1850.00
You Save: $628.97 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68258723AC, 68258723AB, 68258723AA, 68200537AD, 68200537AE
Fits the following Chrysler Models:
- 300 | 2015-2020 | C, C Platinum, Limited, S | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68320183AC
$916.05 MSRP: $1410.00
You Save: $493.95 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68320183AB, 68320183AA
Fits the following Chrysler Models:
- Pacifica | 2017-2025 | L, LX, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
- Voyager | 2020-2024 | L, LX, LXi | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68051891AB
$1320.48 MSRP: $2000.00
You Save: $679.52 (34%)
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 5170580AC, 68051891AC, 5135172AB, 68051891AA, 5135172AC, 5170580AA, 5170580AB, 5135172AD
Fits the following Chrysler Models:
- 300 | 2005-2010 | Base, C, C SRT8, LX, Limited, S, Signature Series, Touring | 2.7L V6, 3.5L V6, 5.7L V8, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6.1L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Chrysler Fuel Tank Part Number: 5085019AC
$807.76 MSRP: $1240.00
You Save: $432.24 (35%)
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel; Tank Fuel
- Replaces: 5085019AB
Fits the following Chrysler Models:
- PT Cruiser | 2004-2010 | Base, Classic, Couture Edition, Dream Cruiser, GT, LX, Limited, Street Cruiser, Touring | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68258722AD
$819.91 MSRP: $1250.00
You Save: $430.09 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68258722AC, 68258722AA, 68258722AB
Fits the following Chrysler Models:
- 300 | 2015-2018 | C, C Platinum, Limited, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68524825AB
$699.47 MSRP: $1070.00
You Save: $370.53 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68524825AA
Fits the following Chrysler Models:
- Pacifica | 2020-2025 | Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2021-2025 | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68217191AF
$689.52 MSRP: $1040.00
You Save: $350.48 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tank - Fuel; Shield
- Replaces: 68217191AD, 68217191AB, 68217191AE, 68217191AC, 68217191AA
Fits the following Chrysler Models:
- 200 | 2015-2017 | C, LX, Limited, S | 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX
View related parts
Chrysler Fuel Tank Part Number: MN106212
Product Specifications
- Other Name: Tank; Tank Assembly
Fits the following Chrysler Models:
- Sebring | 2002-2004 | Base, LX | 4 Cyl 2.4 L GAS
View related parts
Chrysler Fuel Tank Part Number: 4809539AD
Product Specifications
- Other Name: Tank - Fuel
Fits the following Chrysler Models:
- Town & Country | 2003 | Base, EL, EX, LX, LXi, Limited | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2003 | LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Fuel Tank Part Number: 4809739AM
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 4809739AG, 4809739AH, 4809739AJ, 4809739AK, 4809739AL, 4809739AE
Fits the following Chrysler Models:
- Town & Country | 2005-2007 | Base, LX, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68027992AE
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68027992AA, 68027992AD, 68027992AC, 68027992AF, 68027992AB
Fits the following Chrysler Models:
- Aspen | 2008-2009 | Limited | 4.7L V8, 5.7L V8, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chrysler Fuel Tank Part Number: 68319969AD
$839.29 MSRP: $1250.00
You Save: $410.71 (33%)
Product Specifications
- Other Name: Tank - Fuel
- Replaces: 68319969AC, 68319969AA, 68319969AB
Fits the following Chrysler Models:
- Pacifica | 2017 | LX, Limited, Touring, Touring L, Touring L Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Fuel Tank Part Number: 5083108AA
Product Specifications
- Other Name: Tank - Fuel
Fits the following Chrysler Models:
- Concorde | 1998 | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS
View related parts
Chrysler Fuel Tank Part Number: 5013445AB
$581.66 MSRP: $847.00
You Save: $265.34 (32%)
Product Specifications
- Other Name: Tank - Fuel; Tank Fuel
Fits the following Chrysler Models:
- Cirrus | 1999-2000 | LX, LXi | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
- Sebring | 1999-2000 | JX, JXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Fuel Tank Part Number: 4721841AE
$820.97 MSRP: $1205.00
You Save: $384.03 (32%)
Product Specifications
- Other Name: Tank - Fuel; Tank Fuel
- Replaces: 4721841AD, 4721841AC
Fits the following Chrysler Models:
- Town & Country | 2008-2015 | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L, Touring Plus, Walter P. Chrysler Signature Series | 3.3L V6, 3.6L V6, 3.8L V6, 4.0L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Fuel Tank Part Number: 1700A014
Product Specifications
- Other Name: Tank; Tank Assembly; Fuel Tank Assembly
Fits the following Chrysler Models:
- Sebring | 2005 | Base | 4 Cyl 2.4 L GAS
View related parts
Chrysler Fuel Tank Part Number: 1700A015
Product Specifications
- Other Name: Tank; Tank Assembly; Fuel Tank Assembly
Fits the following Chrysler Models:
- Sebring | 2005 | Limited | 6 Cyl 3.0 L GAS
View related parts
Chrysler Fuel Tank Part Number: 4582892
Product Specifications
- Other Name: Tank Fuel; Tank, Fuel
Fits the following Chrysler Models:
- Concorde | 1993-1997 | Base, LX, LXi | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
- LHS | 1994-1997 | Base | 6 Cyl 3.5 L GAS
- New Yorker | 1994-1996 | Base | 6 Cyl 3.5 L GAS
View More
View related parts
Chrysler Fuel Tank Part Number: 4809617AD
Product Specifications
- Other Name: Tank - Fuel
Fits the following Chrysler Models:
- Pacifica | 2007 | Base, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Fuel Tank Part Number: 4865355AC
Product Specifications
- Other Name: Tank - Fuel; Tank Fuel
Fits the following Chrysler Models:
- Prowler | 2001-2002 | Base | 6 Cyl 3.5 L GAS

| Page 1 of 3 |Next >

1-20 of 54 Results

Chrysler Fuel Tank

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler Fuel Tank for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler Fuel Tank, which holds important gasoline, puts the emission in check during every trip. Ever since 1925, Chrysler has been in pursuit of the reality of comfort by reducing engine vibration with Floating Power and modeling cabins with Airflow lines that cut turbulence and subdue ride noise to all. Chrysler continued this pace with the first practical minivan where cramped knees were replaced with flat floors, expansive doors, and sliding seats, and it was found that space and access were better every morning than gimmicks. Value remained on the surface since Chrysler abandoned haggle tricks, set prices that people could afford, and allowed customers to drive away as fast as possible rather than wasting time and patience in showroom theater. Chrysler achieved a reputation of rides that seem to be in contact, silent, and up to anything whether a grocery run or a nationwide trunk move, by focusing on spacious interiors, smooth suspensions, and a no-nonsense usefulness in their cars. The Fuel Tank below the cabin can hold gasoline, fix the pump and gauge sender, and connect the EVAP system to trap the vapor to prevent its escape. Constructed of stamped steel or blow-molded HDPE, every Fuel Tank is puncture resistant, meets factory leak tests, and leaves the line with fresh locking rings and seals fighting years of seepage. Long-range versions are optional and powered by military grade polymer in an effort to ensure that the Fuel Tank can withstand rust and at the same time it can increase the driving range by approximately 500 miles between tanks. The Fuel Tank maintains a shape, closes up tight, and dispenses clean fuel forward even after harsh winters without the groans, drips, or corrosion so common to old steel cans.

Chrysler Fuel Tank Parts and Q&A

Fuel Tank
5013445AB
Q: How to remove the fuel tank on Chrysler Cirrus?
A:
To perform this process first, it requires removing the fuel tank filler cap, so that the pressure could be released. Do fuel pressure relief procedure and remove the negative terminal from the ground stud on the left shock tower. Inside the trunk, look to the left shock tower and fold back the mat there: there is a 4-pin connector for the fuel pump wiring harness; pull this connector off. Go down along the wire to the grommet located at the lower part of the rear seat, push the grommet in the hole in the floor pan and install the wiring and the connector through it. Loosen the fuel tank drain plug while the vehicle is on the ground in a level surface, fill an approved gasoline container and place it under the fuel tank drain plug, taking into consideration the use of the funnel in order to avoid any spillage of fuel when it is being drained. Open the drain plug and let the fuel to flow from the tank and close and tighten the drain plug. Open the clamp and remove the filler neck hose from the fuel tank and leave the quick-connect fuel line of fittings connected to the fuel pump module. At the back part of the fuel tank, remove the vapor hose connection of the rollover valve. Secure the position of the fuel tank by placing a floor jack underneath it; put a piece of wood twixt the jack head and the fuel tank. Take out the fuel tank strap bolts, and straps also. For 1998 models, lower the tank slightly and disconnect the EVAP canister purge line, remove the hoses from the EVAP canister, and remove the electrical connector from the Leak Detection Pump, be sure to label the hoses and fittings for reinstallation. Lower the fuel tank a little in order to remove the rear suspension crossmember then pull the fuel tank out of the car. To remove, undo the procedures mentioned above and fasten a piece of string or wire to the fuel pump module wiring harness then run the wire through the hole at the trunk floorpan of the car. After placing the tank safely secure to the car then pull the string to expose the wiring harness and tighten the fuel tank strap bolts to the torque required.
Fuel Tank
5085019AC
Q: How to remove and reinstall a fuel tank on Chrysler PT Cruiser?
A:
In order to take out the fuel tank, the first step is to unscrew the fuel filler cap a little to release the pressure inside then releasing the system's fuel pressure. Then, bevor the metal with a piece of metal functioning as a ground then, unscrew the nut on the negative terminal of the battery and take out the cable. Lift the car to a safe working height and support it using jackstands on the rear part of the car. Place a drain pan with a capacity of not less than sixteen gallons under the drain cap, remove the fuel tank drain cap, and let the tank drain as long as necessary before replacing the cap. Pull off the vapor hose, unscrew the fuel filler neck hose clam and separate the fuel filler neck hose from the fuel inlet pipe. Put a transmission jack or floor jack in a position to the fuel tank but put a plywood on the head of the jack to avoid scratching it. Pull both of the fuel pump and leak detection electrical connectors, the EVAP line and the quick-connect fitting on the fuel supply hose. Loosen and take out the bolts that holds the fuel tank straps and then slowly dropped the fuel tank of the vehicle. For installation, the process done in the reverse way with the reminder of making sure that the fuel tank strap bolts are tightened and the engine started to look for any leaks at the fuel line connectors that were removed.