How to Install a Wheel Bearing and Hub Assembly on Chrysler Pacifica?

The area on the steering knuckle where the hub and bearing mount should be clean and free of defects. Attach the hub and bearing to the halfshaft stub shaft, then place them into the steering knuckle and press down until it is level. After that, mount the four hub and bearing bolts from the rear of the knuckle into the hub, tightening each bolt evenly and alternately in a cross pattern until you have reached a torque of 65 Nm (45 ft. lbs.). Put the wheel speed sensor cable grommet into the clip connected to the knuckle and secure it. Connect the wheel speed sensor routing bracket to the strut assembly and tighten the screw so that it shows 13 Nm (115 in. lbs.). Attach the connector and routing clip from the wheel speed sensor to the frame rail outer reinforcement and afterwards link the vehicle wiring harness to the connector. Start with the brake rotor, add the disc brake caliper and adapter group and remember to not allow the wheel speed sensor to touch the rotor or any moving braking parts. Attach the washer and hub nut to the end of the halfshaft stub shaft and then with a helper stopping the rotation of the front hub, tighten the hub nut to 244 Nm (180 ft. lbs.). Fit the spring washer and hub nut lock around the hub nut and stub shaft and tighten everything by fitting a new cotter pin through the nut lock, twisting it to wrap the prongs firmly around the lock. Mount the assembly into the vehicle, tighten the wheel nuts to 135 Nm (100 ft. lbs) and allow the car to rest on the ground. Several times, press the brake pedal to ensure it is firm, ensure the brake fluid level is right and perform a wheel alignment.

How to Remove and Service a Wheel Bearing on Chrysler Pacifica?

Before servicing or repairing the wheel bearing, first raise the car onto supports. Remove the wheel mounting nuts first and next, take off the tire and wheel together. Removing these three things from the half shaft is needed only if the vehicle is equipped with AWD. A helper is supposed to use brakes to keep the hub from turning and let you remove the hub nut and washer. After that, remove the brake caliper and rotor from the hub and bearing. Disconnect the wiring connector from the wheel speed sensor at the wheel and then remove the wheel speed sensor connector from its mount on the spare tire holder. Take off the two cable clips from the rear suspension crossmember and those on the toe link. Detach the cable from the sensor at the bracket on the brake support. Leave the brake hub and bearing intact with the bolts only loosened; as you remove the hub and bearing, push the bolts into the rear of the brake support plate so it doesn't move. Get the hub and bearing off the knuckle at the end, using this moment to insert the cable for the wheel speed sensor through the hole in the brake support plate as you remove it.

OEM Chrysler Pacifica Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Wheel Bearings found

View related parts
Chrysler Pacifica Hub & Bearing, Rear Part Number: 68429527AA
$192.61 MSRP: $284.00
You Save: $91.39 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Brake; Rear Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.
- Position: Rear
- Replaces: 68233501AD, 68233501AC, 68233501AE, 68233501AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2019 Chrysler Pacifica | Hybrid Limited, Hybrid Platinum, Hybrid Premium, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Hub & Bearing Part Number: 68522905AB
$173.35 MSRP: $255.00
You Save: $81.65 (33%)
ADD TO CART
Product Specifications
- Other Name: Hub - Brake
- Replaces: 68328069AA, 68522905AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Hub - Brake Part Number: 68624924AA
$219.80 MSRP: $328.00
You Save: $108.20 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: HUB-BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023-2025 Chrysler Pacifica | Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Hub & Bearing, Front Part Number: 68522906AB
$218.67 MSRP: $322.00
You Save: $103.33 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub - Brake; Wheel Bearing and Hub Assembly, Front; Front Hub & Bearing
- Position: Front
- Replaces: 68223504AF, 68223504AC, 68429524AA, 68522906AA, 68223504AB, 68223504AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2023 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Hub & Bearing, Rear Part Number: 4880209AC
$173.35 MSRP: $255.00
You Save: $81.65 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub - Brake; Rear Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.
- Position: Rear
- Replaces: 4880209AA, 4880209AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Pacifica | Base, Limited, Touring | 3.5L V6, 3.8L V6, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Bearing - Brake Part Number: 68319491AB
$214.14 MSRP: $315.00
You Save: $100.86 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: BEARING-BRAKE
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Hub & Bearing, Rear Part Number: 68429526AA
$192.61 MSRP: $284.00
You Save: $91.39 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Brake; Wheel Bearing and Hub Assembly, Rear; Wheel Hub Repair Kit; Wheel Hub; Hub And Bearing Brake; Wheel Bearing
- Position: Rear
- Replaces: 68223512AC, 68223512AD, 68223512AE, 68223512AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Hub & Bearing, Front Part Number: 4721353AC
$203.83 MSRP: $262.00
You Save: $58.17 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Brake; Front Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.; Front Hub
- Position: Front
- Replaces: 4721353AA, 4721353AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 3.8L V6, 4.0L V6, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Hub Part Number: 4880209AB
$201.18 MSRP: $255.00
You Save: $53.82 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub - Brake; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.
- Replaced by: 4880209AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Pacifica | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Hub & Bearing, Front Part Number: 4880208AC
$205.07 MSRP: $303.00
You Save: $97.93 (33%)
ADD TO CART
Product Specifications
- Other Name: Bearing - Brake; Front Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit.; Front Hub
- Position: Front
- Replaced by: 4880208AD
- Replaces: 4880208AA, 4880208AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Chrysler Pacifica | Base, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS

Chrysler Pacifica Wheel Bearing

Choose OEM Wheel Bearing that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Wheel Bearing follows strict manufacturing steps to lock in quality and fit. If your Chrysler Pacifica matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Pacifica parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Chrysler Pacifica Wheel Bearing is one of the best if not the best products that contribute to a better performance of Chrysler Pacifica vehicles. As designed to enable the advantageous rotation of the wheels, this Wheel Bearing reduces presence of friction, thus allowing proper operation of the wheels and tires. Three main styles of hub and bearings are used in models of Chrysler Pacifica; the integral hub and bearing assembly are standard with this package; they frequently come with an ABS sensor for safety enhancements. The Wheel Bearing requires frequent check-ups and replacements due to the fact that if the bearing is weak or not properly fixed, it will produce noise and cause the vehicle to vibrate and could even pose a serious danger to the vehicle's safety. The compatibility between the Chrysler Pacifica and other models is made possible so that the drivers have the best result for functioning and performance. Further, Wheel Bearing is another component that has a great influence in increasing the efficiency of the vehicle and has a role to play in providing the soft and proper handling of the vehicle. Some of the features are as follows: replaceable tapered roller bearings in non-driven axle hubs for Chrysler Pacifica Wheel Bearing distinguish it from other similar products in the automotive industry. Thanks to for its reliability and good performance, Chrysler Pacifica Wheel Bearing is crucial for the safety and performance of Chrysler Pacifica cars; therefore, it is a perfect decision for those who are searching for a high-quality and reliable spare part for their car.

Chrysler Pacifica Wheel Bearing Parts and Q&A

Hub
4880209AB
Q: How to Install a Wheel Bearing and Hub Assembly on Chrysler Pacifica?
A:
The area on the Steering Knuckle where the hub and bearing mount should be clean and free of defects. Attach the hub and bearing to the halfshaft stub shaft, then place them into the steering knuckle and press down until it is level. After that, mount the four hub and bearing bolts from the rear of the knuckle into the hub, tightening each bolt evenly and alternately in a cross pattern until you have reached a torque of 65 Nm (45 ft. lbs.). Put the wheel speed sensor cable grommet into the clip connected to the knuckle and secure it. Connect the wheel speed sensor routing bracket to the strut assembly and tighten the screw so that it shows 13 Nm (115 in. lbs.). Attach the connector and routing clip from the wheel speed sensor to the frame rail outer reinforcement and afterwards link the vehicle wiring harness to the connector. Start with the brake rotor, add the disc Brake Caliper and adapter group and remember to not allow the wheel speed sensor to touch the rotor or any moving braking parts. Attach the washer and hub nut to the end of the halfshaft stub shaft and then with a helper stopping the rotation of the front hub, tighten the hub nut to 244 Nm (180 ft. lbs.). Fit the spring washer and hub nut lock around the hub nut and stub shaft and tighten everything by fitting a new cotter pin through the nut lock, twisting it to wrap the prongs firmly around the lock. Mount the assembly into the vehicle, tighten the wheel nuts to 135 Nm (100 ft. lbs) and allow the car to rest on the ground. Several times, press the brake pedal to ensure it is firm, ensure the brake fluid level is right and perform a wheel alignment.
Hub & Bearing, Front
4721353AC
Q: How to Remove and Service a Wheel Bearing on Chrysler Pacifica?
A:
Before servicing or repairing the wheel bearing, first raise the car onto supports. Remove the wheel mounting nuts first and next, take off the tire and wheel together. Removing these three things from the half shaft is needed only if the vehicle is equipped with AWD. A helper is supposed to use brakes to keep the hub from turning and let you remove the hub nut and washer. After that, remove the Brake Caliper and rotor from the hub and bearing. Disconnect the wiring connector from the wheel speed sensor at the wheel and then remove the wheel speed sensor connector from its mount on the spare tire holder. Take off the two cable clips from the rear suspension crossmember and those on the toe link. Detach the cable from the sensor at the bracket on the brake support. Leave the brake hub and bearing intact with the bolts only loosened; as you remove the hub and bearing, push the bolts into the rear of the brake support plate so it doesn't move. Get the hub and bearing off the knuckle at the end, using this moment to insert the cable for the wheel speed sensor through the hole in the brake support plate as you remove it.