How to Maintain and Fix Oxygen Sensors on Chrysler Sebring?

Start by waiting for the engine to cool, take off the negative battery cable and raise the car before servicing the oxygen sensors. Before you remove the side oxygen sensors, disconnect the wiring, keeping your hands away from the wires and then use a Snap-On oxygen sensor wrench (number YA 8875). You should also remove the electrical connector for the heated oxygen sensor in the exhaust manifold but be careful not to pull on the wire and use a tool like a Snap-On YA8875 or crowfoot wrench to remove it. When you take out a sensor, first clean the exhaust manifold threads with an 18 mm X 1.5 + 6E tap. Should you use the old sensor, apply anti-seize grease to avoid rusting, for example, Loctite 771-64; new sensors are coated with it. Instead, begin by installing the oxygen sensors, turning them to 28 Nm (20 ft. lbs.) of torque, placing the wire connectors securely and taking the vehicle for a lowering.

How to Remove and Install the Rear Oxygen Sensor in the Engine on Chrysler Sebring?

There are two heated oxygen sensors, each one positioned in its own exhaust manifold. First, unlink the negative battery cable and take out the air cleaner box to remove the rear O2 sensor. After that, detach the hot oxygen sensor wire connector and use Special tool #8439 to take out the unit. Before installing, use an 18 mm X 1.5 + 6E tap to clean out the exhaust manifold. If you use the old sensor, coat the threads of the sensor with anti-seize compound, but pre-coated sensors won't require you to add that material. After removing the oxygen sensor, install it using Special tool #8439 and fasten it to 28 Nm (20 ft. lbs.) of torque. Afterwards, stay below the heat of the engine and reconnect the heated oxygen sensor's electrical connector. Then, fit back the air cleaner box and reconnect the negative battery cable last.

OEM Chrysler Sebring Oxygen Sensor

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

38 Oxygen Sensors found

View related parts
Chrysler Sebring Oxygen Sensor, Front Part Number: MD354851
$220.26 MSRP: $279.22
You Save: $58.96 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Sebring | LX, LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606523
Product Specifications
- Other Name: Sensor; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Rear Driver Side Part Number: MN158759
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear Left; Sensor Oxygen
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chrysler Sebring | LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606950AB
Product Specifications
- Other Name: Sensor - Oxygen; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Sebring | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606037
Product Specifications
- Other Name: Sensor; Sensor, Oxygen, P Series; Sensor, Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Chrysler Sebring | LX, LXi | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606071
Product Specifications
- Other Name: Sensor - Oxygen; Sensor, Oxygen, P Series; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1998 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606091
Product Specifications
- Other Name: Sensor - Oxygen; Sensor, Engine Electric Control Oxygen; Sensor, Oxygen, P Series; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1998 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606327
Product Specifications
- Other Name: Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606422
Product Specifications
- Other Name: Sensor; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Front Part Number: 4606555AD
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2004 Chrysler Sebring | Base, GTC, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606624
Product Specifications
- Other Name: Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 4606626
Product Specifications
- Other Name: Sensor; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chrysler Sebring | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Sebring Oxygen Sensor Part Number: 5269744
Product Specifications
- Other Name: Sensor; Sensor Oxygen
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Chrysler Sebring | LX
View related parts
Chrysler Sebring Oxygen Sensor, Rear Part Number: MD345230
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Sensor Oxygen
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Sebring | LX, LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Front Part Number: MD354850
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Right; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler Sebring | LX, LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Front Driver Side Part Number: MN158758
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left; Sensor Oxygen
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chrysler Sebring | LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Front Part Number: MR507385
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Right; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Front Part Number: MR507386
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Rear Passenger Side Part Number: MR507387
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear, Rear Right; Sensor Oxygen
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Chrysler Sebring | LXi | 6 Cyl 3.0 L GAS
View related parts
Chrysler Sebring Oxygen Sensor, Front Part Number: MR560364
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front; Front Oxygen Sensor; Sensor Oxygen
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Sebring | Base, LX | 4 Cyl 2.4 L GAS

| Page 1 of 2 |Next >

1-20 of 38 Results

Chrysler Sebring Oxygen Sensor

Choose OEM Oxygen Sensor that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Oxygen Sensor follows strict manufacturing steps to lock in quality and fit. If your Chrysler Sebring matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Sebring parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Oxygen Sensor is also predictably installed in Chrysler Sebring cars and it monitors the quantity of the unburned oxygen in the exhaust, which is imperative to the correct proportions of the air-fuel mixture and reduced emissions. The sensor generates a voltage signal in accordance with the oxygen concentration, and the computer of a car engine determines whether the mixture is rich or lean in order to adjust the fuel Injector timing accordingly. Common Chrysler Sebring have zirconia oxygen sensors, both: narrow and wide range. The first type of sensors includes the narrow-band which deliver varying rich/lean signals, the other type being the wide-band which offers a wider air-fuel mixture range. The first aspect represents the basic difference in the operation of such devices with wideband sensors giving better details for fuel control. These sensors, which include oxygen sensor, inevitably suffered from contamination and therefore brings about increase in emissions and poor fuel consumption for Chrysler Sebring vehicles.

Chrysler Sebring Oxygen Sensor Parts and Q&A

Oxygen Sensor, Front
4606133AD
Q: How to Maintain and Fix Oxygen Sensors on Chrysler Sebring?
A:
Start by waiting for the engine to cool, take off the negative Battery Cable and raise the car before servicing the oxygen sensors. Before you remove the side oxygen sensors, disconnect the wiring, keeping your hands away from the wires and then use a Snap-On oxygen sensor wrench (number YA 8875). You should also remove the electrical connector for the heated oxygen sensor in the Exhaust Manifold but be careful not to pull on the wire and use a tool like a Snap-On YA8875 or crowfoot wrench to remove it. When you take out a sensor, first clean the exhaust manifold threads with an 18 mm X 1.5 + 6E tap. Should you use the old sensor, apply anti-seize grease to avoid rusting, for example, Loctite 771-64; new sensors are coated with it. Instead, begin by installing the oxygen sensors, turning them to 28 Nm (20 ft. lbs.) of torque, placing the wire connectors securely and taking the vehicle for a lowering.
Oxygen Sensor, Rear Driver Side
MN158759
Q: How to Remove and Install the Rear Oxygen Sensor in the Engine on Chrysler Sebring?
A:
There are two heated oxygen sensors, each one positioned in its own Exhaust Manifold. First, unlink the negative Battery Cable and take out the air cleaner box to remove the rear O2 sensor. After that, detach the hot oxygen sensor wire connector and use Special tool #8439 to take out the unit. Before installing, use an 18 mm X 1.5 + 6E tap to clean out the exhaust manifold. If you use the old sensor, coat the threads of the sensor with anti-seize compound, but pre-coated sensors won't require you to add that material. After removing the oxygen sensor, install it using Special tool #8439 and fasten it to 28 Nm (20 ft. lbs.) of torque. Afterwards, stay below the heat of the engine and reconnect the heated oxygen sensor's electrical connector. Then, fit back the air cleaner box and reconnect the negative battery cable last.