How to Service and Repair a Brake Light Switch on Chrysler Town & Country?

Before anything else, make sure the battery's negative cable is disconnected and put aside. Remove the silencer panel below the steering column and also the knee blocker. After that, turn the brake lamp switch counterclockwise roughly 30 degrees and pull it out of the bracket. Throw away the old switch, as it should not be reused. For the installation, place and align the switch on the bracket and turn it clockwise about 300 times so it locks in place. When you let go of the brake pedal, shift the lever on the back of the brake lamp switch so that it lines up vertically with the case to set the switch in the vehicle. Now, put on the silencer panel and connect the battery negative wire after it has been installed. Finally, test all the stop lamps to make sure they are working correctly and don't stay on once you release the pedal and conduct a road test to check that the brakes, ABS and speed control are operating as they should.

How to Install a Brake Light Switch on Chrysler Town & Country?

Before you fit the brake light switch, disconnect and isolate the car's negative battery cable, disable the SRS and wait for two minutes to let the capacitor lose all its charge. Making certain the brake lamp switch plunger is in the fully extended position, reconnect the body wire harness connector with the switch. Set your foot on the brake pedal until it is depressed, put the keyed locking collar on the brake lever switch and insert it into the square hole in the bracket until the switch housing is secured tightly against it. Turn the switch housing to the right about 30 degrees until the locking collar satisfies the mounting bracket and make sure not to pull the brake pedal beyond 9 kilograms (20 pounds). Press the release pedal down all the way and then carefully pull it up to where it rests while the plunger makes a light noisy ratcheting sound. To finish, attach the negative battery cable to its lead once again.

OEM Chrysler Town & Country Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Brake Light Switches found

View related parts
Chrysler Town & Country Parking Brake Switch, Black Part Number: 4221463
$18.50 MSRP: $27.20
You Save: $8.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Parking Brake; Electronic Parking Brake Control Switch; Parking Brake Warning Switch; Seat Adjuster, W/Bezel, Black Buttons, Woodgrain, W/Memory Opening.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016, 1991-1995 Chrysler Town & Country | 30th Anniversary Edition, Base, LX, Limited, Limited Platinum, S, Touring, Touring L | 6 Cyl 3.3 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Brake Switch Part Number: 4671336AD
$39.68 MSRP: $53.75
You Save: $14.07 (27%)
ADD TO CART
Product Specifications
- Other Name: Switch - Stop Lamp; Brake Light Switch; Stop Light Switch; Brake Pedal Switch; Lamp Switch; Release Switch; Stoplamp Switch; Switch; Switch Stop Lamp
- Replaces: 4671336, 4671336AC, 4671336AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2016 Chrysler Town & Country | 3.3L V6, 3.6L V6, 3.8L V6, 4.0L V6
- 1997-2000 Chrysler Town & Country | 3.3L V6, 3.8L V6
View related parts
Chrysler Town & Country Brake Switch Part Number: 68003916AA
$35.51 MSRP: $51.80
You Save: $16.29 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Stop Lamp; Brake Pedal Switch; Stoplamp Switch
- Replaces: 4671334
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Chrysler Town & Country | Base, LX, LXi | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Stoplamp Switch Part Number: 4373145
$27.09 MSRP: $34.34
You Save: $7.25 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Stop Lamp & Speed Control; Switch, Stop Lamp And Speed Control; Stop Lamp, W/O Speed Control; Stop Lamp, W/Speed Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-1988 Chrysler Town & Country | Base | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
View related parts
Chrysler Town & Country Brake Switch Part Number: 4373535
Product Specifications
- Other Name: Switch; Brake Light Switch; Brake Pedal Switch; Stoplamp Switch; Use Bracket 4221487; Striker 4221488; Speed Control.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chrysler Town & Country | Base | 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Stoplamp Switch Part Number: 4373147
Product Specifications
- Other Name: Switch Stop Lamp & Speed Control; Switch, Stop Lamp And Speed Control; Stop Lamp, W/Speed Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Switch Package - Stop Lamp Part Number: 5083344AB
Product Specifications
- Other Name: SW PKG-STOP LAMP
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2009 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 3.3L V6, 3.5L V6, 3.8L V6, 4.0L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS

Chrysler Town & Country Brake Light Switch

Choose OEM Brake Light Switch that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Light Switch follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Brake Light Switch is such an important switch because it controls the brake light whenever the brake pedal is pressed in Chrysler Town & Country Vehicles. This mechanism facilitates the development of an awareness on the part of the drivers heading the Chrysler Town & Country that the car is slowing down or even staking, which in essence improves safety within the roads. While the overview does not specify different types or styles of Brake Light Switch used in various Chrysler Town & Country models, it is essential to note that the primary goal remains consistent across all iterations: to provide an efficient way of signalling braking actions. The Brake Light Switch is a very essential device in relaying signal to other drivers on the road hence making a very useful contribution to the overall safety drive in the Chrysler Town & Country.

Chrysler Town & Country Brake Light Switch Parts and Q&A

Switch Package - Stop Lamp
5083344AB
Q: How to Service and Repair a Brake Light Switch on Chrysler Town & Country?
A:
Before anything else, make sure the battery's negative cable is disconnected and put aside. Remove the silencer panel below the steering column and also the knee blocker. After that, turn the brake lamp switch counterclockwise roughly 30 degrees and pull it out of the bracket. Throw away the old switch, as it should not be reused. For the installation, place and align the switch on the bracket and turn it clockwise about 300 times so it locks in place. When you let go of the brake pedal, shift the lever on the back of the brake lamp switch so that it lines up vertically with the case to set the switch in the vehicle. Now, put on the silencer panel and connect the battery negative wire after it has been installed. Finally, test all the stop lamps to make sure they are working correctly and don't stay on once you release the pedal and conduct a road test to check that the brakes, ABS and speed control are operating as they should.
Brake Switch
4671336AD
Q: How to Install a Brake Light Switch on Chrysler Town & Country?
A:
Before you fit the brake light switch, disconnect and isolate the car's negative battery cable, disable the SRS and wait for two minutes to let the capacitor lose all its charge. Making certain the brake lamp switch plunger is in the fully extended position, reconnect the body wire harness connector with the switch. Set your foot on the brake pedal until it is depressed, put the keyed locking collar on the brake lever switch and insert it into the square hole in the bracket until the switch housing is secured tightly against it. Turn the switch housing to the right about 30 degrees until the locking collar satisfies the mounting bracket and make sure not to pull the brake pedal beyond 9 kilograms (20 pounds). Press the release pedal down all the way and then carefully pull it up to where it rests while the plunger makes a light noisy ratcheting sound. To finish, attach the negative battery cable to its lead once again.