How to Service and Repair a Brake Light Switch on Dodge Dakota?

Before servicing or repairing the brake light switch, first remove the switch harness. Press and hold the brake pedal down. After that, turn the switch counterclockwise about 30 degrees so the switch lock tab fits into the notch in the bracket. Now, pull the switch rearward and release the brake pedal. To install, make sure you press the brake pedal, steer the tab of the switch into the notch on the switch bracket, insert the switch and turn it 30 degrees clockwise to tighten it. Connect the wires from the harness to the switch, release the brake pedal, move the release lever on the switch to engage the plunger and you're finished with the adjustment.

How to Replace a Brake Light Switch on Dodge Dakota?

The first step in installing the brake light switch is to disconnect and isolate the battery negative cable, disable the SRS and allow two minutes for the system capacitor to discharge. This switch has a plunger that can adjust itself and should be swapped out if taken from the mounting bracket. Depress the brake pedal at the begining and maintain the pressure. Position the tabs from the brake lamp switch locking collar above the keyed hole on the bracket holding the switch to the steering column. Push the tabs through the hole until the switch housing fits against the bracket, after which turn the switch housing counterclockwise about 30 degrees to secure it to the bracket. You should not apply or release pressure on the brake pedal before adjusting the switch plunger. Without pulling up the brake pedal, rotate the plunger adjustment release lever clockwise until it fixes into place straight alongside the brake lamp switch connector receptacle. Setting up the plunger locks its size; failure to do this properly requires installing a new brake lamp switch. Afterwards, rejoin the wire harness connector to the brake lamp switch and reconnect the negative terminal from the battery.

OEM Dodge Dakota Brake Light Switch

Brake Lamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Light Switches found

View related parts
Dodge Dakota Parking Brake Switch, Black Part Number: 4221463
$18.50 MSRP: $27.20
You Save: $8.70 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Parking Brake; Electronic Parking Brake Control Switch; Parking Brake Warning Switch; Seat Adjuster, W/Bezel, Black Buttons, Woodgrain, W/Memory Opening.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1988-2010 Dodge Dakota | Base, Big Horn, LE, Laramie, Lone Star, R/T, S, SE, SLT, SLT Plus, ST, SXT, Shelby, Sport, Sport Plus, TRX, TRX4, WS | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Brake Switch Part Number: 4671336AD
$39.68 MSRP: $53.75
You Save: $14.07 (27%)
ADD TO CART
Product Specifications
- Other Name: Switch - Stop Lamp; Brake Light Switch; Stop Light Switch; Brake Pedal Switch; Lamp Switch; Release Switch; Stoplamp Switch; Switch; Switch Stop Lamp
- Replaces: 4671336, 4671336AC, 4671336AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2011 Dodge Dakota | Big Horn, Laramie, Lone Star, ST, TRX4 | 3.7L V6, 4.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX
View related parts
Dodge Dakota Brake Switch Part Number: 68003916AA
$35.51 MSRP: $51.80
You Save: $16.29 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Stop Lamp; Brake Pedal Switch; Stoplamp Switch
- Replaces: 4671334
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Dakota | Base, R/T, SLT, Sport | 2.5L L4, 3.9L V6, 4 Cyl 2.5 L GAS, 5.2L V8, 5.9L V8, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Brake Switch Part Number: 4373535
Product Specifications
- Other Name: Switch; Brake Light Switch; Brake Pedal Switch; Stoplamp Switch; Use Bracket 4221487; Striker 4221488; Speed Control.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1988-1997 Dodge Dakota | Base, LE, S, SE, SLT, Shelby, Sport, WS | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS
View related parts
Dodge Dakota Brake Pedal Switch Part Number: 5016294AD
Product Specifications
- Other Name: Switch Package - Stop Lamp; Brake Light Switch; Stop Light Switch; Stoplamp Switch
- Replaces: 56045043AC, 5016294AB, 5016294AA, 56045043AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2000 Dodge Dakota | Base, R/T, SLT, Sport | 2.5L L4, 3.9L V6, 4 Cyl 2.5 L GAS, 4.7L V8, 5.2L V8, 5.9L V8, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Switch Package - Stop Lamp Part Number: 5083344AB
Product Specifications
- Other Name: SW PKG-STOP LAMP
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2009 Dodge Dakota | Base, Big Horn, Laramie, Lone Star, R/T, SLT, SLT Plus, ST, SXT, Sport, Sport Plus, TRX, TRX4 | 2.5L L4, 3.7L V6, 3.9L V6, 4 Cyl 2.5 L GAS, 4.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS

Dodge Dakota Brake Light Switch

Choose OEM Brake Light Switch that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Light Switch follows strict manufacturing steps to lock in quality and fit. If your Dodge Dakota matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Dakota parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Brake Light Switch in Dodge Dakota cars play an important role for the working of brake light every time the break pedal is pressed. This mechanism helps the drivers at the back of the Dodge Dakota to be informed when the vehicle is either slowing down or has come to a standstill which dramatically reduces on the road accidents. While the overview does not specify different types or styles of Brake Light Switch used in various Dodge Dakota models, it is essential to recognize that the primary goal remains consistent across all iterations: needs to be effectively used in order to give correct signals for braking actions adequately. The Brake Light Switch play an important role in informing other drivers on the road of the car's status and therefore plays an important role in as far as safety is concerned.

Dodge Dakota Brake Light Switch Parts and Q&A

Parking Brake Switch, Black
4221463
Q: How to Service and Repair a Brake Light Switch on Dodge Dakota?
A:
Before servicing or repairing the brake light switch, first remove the switch harness. Press and hold the brake pedal down. After that, turn the switch counterclockwise about 30 degrees so the switch lock tab fits into the notch in the bracket. Now, pull the switch rearward and release the brake pedal. To install, make sure you press the brake pedal, steer the tab of the switch into the notch on the switch bracket, insert the switch and turn it 30 degrees clockwise to tighten it. Connect the wires from the harness to the switch, release the brake pedal, move the release lever on the switch to engage the plunger and you're finished with the adjustment.
Switch Package - Stop Lamp
5083344AB
Q: How to Replace a Brake Light Switch on Dodge Dakota?
A:
The first step in installing the brake light switch is to disconnect and isolate the battery negative cable, disable the SRS and allow two minutes for the system capacitor to discharge. This switch has a plunger that can adjust itself and should be swapped out if taken from the mounting bracket. Depress the brake pedal at the begining and maintain the pressure. Position the tabs from the brake lamp switch locking collar above the keyed hole on the bracket holding the switch to the steering column. Push the tabs through the hole until the switch housing fits against the bracket, after which turn the switch housing counterclockwise about 30 degrees to secure it to the bracket. You should not apply or release pressure on the brake pedal before adjusting the switch plunger. Without pulling up the brake pedal, rotate the plunger adjustment release lever clockwise until it fixes into place straight alongside the brake lamp switch connector receptacle. Setting up the plunger locks its size; failure to do this properly requires installing a new brake lamp switch. Afterwards, rejoin the wire harness connector to the brake lamp switch and reconnect the negative terminal from the battery.