How to Maintain and Fix a Rocker Arm on Dodge Durango?

To work on or fix the rocker arm assembly, first lift off the cylinder head cover and the gasket underneath it. After that, pull out the rocker arm bolts and pivots, keeping them in the same order as you take them out; next, take out the push rods and also arrange them in the same order as removed. Rotate the crankshaft to line up the "V8" mark with the TDC mark found on the timing chain cover at a measured distance of 147° ATDC fires from the No.1 firing perch. Assemble the push rods inside the engine in the same order they were removed. Next, put the rocker arm assemblies and pivots into place, tightening the bolts of the rocker arms to 28 Nm (21 ft. lbs.) torque. You should not turn or crank the engine for a few minutes after installing the rocker arm; instead, give the hydraulic roller tappets at least 5 minutes to drain excess oil before installing the cylinder head cover.

How to Service a Rocker Arm Assembly on Dodge Durango?

Start the service of the rocker arm assembly by taking out the cylinder head cover and gasket. Remove the rocker arm bolts and pivots, adding each one to a bench in the exact order they were taken out and then do the same with the push rods. Turn the crankshaft so the "V8" mark comes into alignment with the TDC mark on the timing chain case cover which is 147° from the front of the engine. Security from the No.1 angle during an attack. Place the push rods on the valves following the same order used when removing them and bolt the rocker arm and pivot assemblies in the same order with tightened bolts of 28 Nm (21 ft. lbs.). Cranking or rotating the engine in any way during or following the installation should be avoided; give the hydraulic roller tappets about 5 minutes to empty after installation to avoid problems.

OEM Dodge Durango Rocker Arm

Engine Rocker Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Rocker Arms found

View related parts
Dodge Durango Rocker Arms Part Number: 53020742AC
$33.86 MSRP: $44.05
You Save: $10.19 (24%)
ADD TO CART
Product Specifications
- Other Name: Arm - Valve; Rocker Arm; Rocker Arm Valve
- Replaces: 68045794AA, 53021913AB, 53020742AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2009 Dodge Durango | Adventurer, Base, Limited, SE, SLT, SLT Plus, ST, SXT, Sport | 3.7L V6, 4.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Rocker Arms Part Number: 5047896AD
$85.12 MSRP: $129.00
You Save: $43.88 (35%)
ADD TO CART
Product Specifications
- Other Name: Arm - Valve; Rocker Arm; Rocker Arm Valve Intake Valve; Rocker Arm Valve Intake; Rocker Arm Valve
- Replaces: 5047896AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2025 Dodge Durango | Citadel, GT, GT Plus, GT Premium, Limited, Pursuit, SXT, SXT Plus, Special Service | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Durango Rocker Arms Part Number: 53021552AB
$152.96 MSRP: $227.00
You Save: $74.04 (33%)
ADD TO CART
Product Specifications
- Other Name: Arm - Intake; Rocker Arm; Intake Rocker Arm; Rocker Arm Intake
- Replaces: 53021552AA, 68060343AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2025 Dodge Durango | 5.7L V8
- 2004-2009 Dodge Durango | 5.7L V8
View related parts
Dodge Durango Rocker Arms Part Number: 53008282
$33.17 MSRP: $48.95
You Save: $15.78 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm - Valve; Rocker Arm; Rocker Arm Valve; Rocker, Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2003 Dodge Durango | Base, R/T, SLT, SLT Plus, SXT, Sport | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Durango Rocker Arms Part Number: 53021553AB
$151.61 MSRP: $227.00
You Save: $75.39 (34%)
ADD TO CART
Product Specifications
- Other Name: Arm - Exhaust; Rocker Arm; Exhaust Rocker Arms; Rocker Arm Exhaust
- Replaces: 53021553AA, 68060344AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2025 Dodge Durango | 5.7L V8
- 2004-2009 Dodge Durango | 5.7L V8
View related parts
Dodge Durango Rocker Arms Part Number: 5184296AH
$16.24 MSRP: $23.45
You Save: $7.21 (31%)
ADD TO CART
Product Specifications
- Other Name: Arm - Valve; Rocker Arm; Rocker Arm Valve
- Replaces: 5184296AG, 5184296AD, 5184296AE, 5184296AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Express, Heat, Limited, Rallye, SXT, Special Service | 3.6L V6, 6 Cyl 3.6 L FLEX
View related parts
Dodge Durango Rocker Pivot Part Number: 53008283
$14.57
ADD TO CART
Product Specifications
- Other Name: Arm - Rocker Arm; Rocker Arm Pivot; Pivot, Rocker Arm; Pivot Rocker Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2003 Dodge Durango | Base, R/T, SLT, SLT Plus, SXT, Sport | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Durango Rocker Arms Part Number: 68245463AA
$14.82 MSRP: $22.10
You Save: $7.28 (33%)
ADD TO CART
Product Specifications
- Other Name: Arm - Includes Lash Adjuster; Rocker Arm; Rocker Arm Assembly Includes Lash Adjuster Exhaust Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2025 Dodge Durango | Citadel, GT, GT Plus, GT Premium, Limited, Pursuit, SXT, SXT Plus, Special Service | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS

Dodge Durango Rocker Arm

Choose OEM Rocker Arm that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Rocker Arm follows strict manufacturing steps to lock in quality and fit. If your Dodge Durango matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Durango parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Rocker Arm that operates in Dodge Durango vehicles exploits a significant position in the valvetrain of the internal combustion engine by converting motion from the pushrod to the intake and exhaust valves. Usually made from stamped steel or aluminium, the Rocker Arm has the responsibility of moving up and down to open the valves in response to the pushrod's vertical movement. For high RPM engines like found in modern cars, aluminum is used because of its light weight nature, although for commercial vehicles and diesel engines and such, cast iron or forged carbon steel is preferred. In the course of its production, Dodge Durango could have normal Rocker Arms, like, Rollers. Roller rockers, which come with needle bearings in order to smoothen the rolling process, are ideal for both the overhead valve engines and the overhead camshaft engines. The rocker ratio that varies from 1.5:1 to 1.8:1 in present day engines can boost camshaft lift therefore the performance. Other example of automobile part, that has been altered for higher stress, RPM or corrosive exposure, can also be seen in the upgraded fulcrum bearings installed in Dodge Durango engines to bear the stress.

Dodge Durango Rocker Arm Parts and Q&A

Rocker Pivot
53008283
Q: How to Maintain and Fix a Rocker Arm on Dodge Durango?
A:
To work on or fix the rocker arm assembly, first lift off the cylinder head cover and the gasket underneath it. After that, pull out the rocker arm bolts and pivots, keeping them in the same order as you take them out; next, take out the push rods and also arrange them in the same order as removed. Rotate the Crankshaft to line up the "V8" mark with the TDC mark found on the timing chain cover at a measured distance of 147° ATDC fires from the No.1 firing perch. Assemble the push rods inside the engine in the same order they were removed. Next, put the rocker arm assemblies and pivots into place, tightening the bolts of the rocker arms to 28 Nm (21 ft. lbs.) torque. You should not turn or crank the engine for a few minutes after installing the rocker arm; instead, give the hydraulic roller tappets at least 5 minutes to drain excess oil before installing the cylinder head cover.
Rocker Arms
53020742AC
Q: How to Service a Rocker Arm Assembly on Dodge Durango?
A:
Start the service of the rocker arm assembly by taking out the cylinder head cover and gasket. Remove the rocker arm bolts and pivots, adding each one to a bench in the exact order they were taken out and then do the same with the push rods. Turn the Crankshaft so the "V8" mark comes into alignment with the TDC mark on the timing chain case cover which is 147° from the front of the engine. Security from the No.1 angle during an attack. Place the push rods on the valves following the same order used when removing them and bolt the rocker arm and pivot assemblies in the same order with tightened bolts of 28 Nm (21 ft. lbs.). Cranking or rotating the engine in any way during or following the installation should be avoided; give the hydraulic roller tappets about 5 minutes to empty after installation to avoid problems.