What Steps Should Be Taken Before Replacing the Engine Control Module for a Failed Driver, Control Circuit, or Ground Circuit on Dodge Neon?

Repairers should first confirm related parts and circuits are working correctly before replacing the Pcm if a fault is not noticed due to a double failure. Many issues with Pcm drivers and control circuits result from failing 12-volt pull-ups, drivers and ground sensors inside the circuit. Identifying them can be difficult when only one Dtc is set. Instruction manual If both the Pcm and Skim have to be replaced at once, first put the Vin into the Pcm and then program all of the keys to the new Skim. Each Skis has a secret key special I.d. stored in three places-the Skim, engine controller and transponder chip (ignition key), so the secret key must be reprogrammed into the Pcm if the part is replaced. Program the pinion factor by turning on your ignition, setting the transmission to park or neutral and using the Drbiii(R) to select Theft Alarm, Skim, then Miscellaneous and choose Pcm Replaced. Secure access mode will be activated with the vehicle's four-digit Pin. After two incorrect tries, the system will lock out for one hour and need your ignition in the run position for a full hour before you can try again. Shut off all the accessories and make sure the battery has enough charge; connect a battery charger if it's low. After that, press Enter to put the secret key on the Pcm from the Skim.

How to Remove and Reinstall an Engine Control Module on Dodge Neon?

Before taking the Engine Control Module out, unplug the negative battery cable. After that, take out and replace the air cleaner box. Open and part the electrical connectors on the PCM and then free up the wiring harness dip from its bracket. Afterward, take out the mounting bolts under the PCM bracket, then the nut and screws for the bracket itself. After bracket removal, unclip the PCM while taking out the hard parts of your PL 2.4L SRT-4. After you have removed the assembly, PCM and bracket, return the assembly to its original spot and only screw on the mounting nut loosely. Put the mounting bolts through the PCM bracket from the bottom and make sure to tighten the bolt nut. Add the wiring harness clip to the PCM bracket so that all the connectors for the PCM are the right colors. Link the connector from the PCM to the air cleaner, locking them together and once more place the air cleaner box back into place. Lastly, attach the negative battery cable again.

OEM Dodge Neon Engine Control Module

Engine Control Computer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

48 Engine Control Modules found

View related parts
Dodge Neon ECM Part Number: 5269996AC
$405.33 MSRP: $590.00
You Save: $184.67 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module; Module Engine Controller
- Replaced by: 5269996AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: 5269821AC
$118.80 MSRP: $172.00
You Save: $53.20 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module; Module Engine Controller
- Replaced by: R5269821AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Dodge Neon | ACR, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: 5293018AS
$414.83 MSRP: $600.00
You Save: $185.17 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module
- Replaced by: R5033098AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Dodge Neon | ES, High Line | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: 5161105AA
$599.33 MSRP: $901.00
You Save: $301.67 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module; Module Powertrain Control Generic
- Replaces: RL161105AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Neon | SE, SXT | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R5033098AG
Product Specifications
- Other Name: Module - Engine Controller
- Replaces: 5033098AE, 5033098AG, 5033098AF, 5033098AB, 5293018AS, 5033098AC, 5033098AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Dodge Neon | ES, High Line | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R5269939
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module; ECM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R5269995AD
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module; ECM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R4874156
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module; ECM
- Replaces: 4874156
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R5269942
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R5269815AK
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Dodge Neon | ACR, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R4874154
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module; ECM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R5269940
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R4874163
Product Specifications
- Other Name: Module - Engine Controller
- Replaces: 4874163
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995 Dodge Neon | High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R4874165
Product Specifications
- Other Name: Module - Engine Controller
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995 Dodge Neon | High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R5033176AF
Product Specifications
- Other Name: Module - Powertrain Control
- Replaces: 5033176AF, 5033176AE, RL033176AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2001 Dodge Neon | ACR, Base, ES, High Line, R/T, SE | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R4874155
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module; Module
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R4874158
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon ECM Part Number: R5293004AD
Product Specifications
- Other Name: Module - Engine Controller; Engine Control Module
- Replaces: 5293004AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R5269998AD
Product Specifications
- Other Name: Module - Engine Controller; ECM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Neon Control Module Part Number: R5269945
Product Specifications
- Other Name: Module - Powertrain Control; Engine Control Module; ECM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Dodge Neon | Base, High Line, Sport | 4 Cyl 2.0 L GAS

| Page 1 of 3 |Next >

1-20 of 48 Results

Dodge Neon Engine Control Module

Choose OEM Engine Control Module that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Engine Control Module follows strict manufacturing steps to lock in quality and fit. If your Dodge Neon matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Neon parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

One of the key reasons that defines the prospects and efficiency of Dodge Neon vehicles is the part called Engine Control Module or ECM. As the main controller of the Dodge Neon's engine, the Engine Control Module constantly supervises and coordinates the execution of operations with the help of signals from sensors, decides the amount of fuel and air mixture, controls ignition coils, and stores crucial program information. This high technology does not only boost the functionality of the Dodge Neon but it also helps a lot in the aspect of safety since it regulates the performance of the engine. As used for the models of the Dodge Neon, the Engine Control Module is offered either new or remanufactured, thus making fit every car perfectly. Thus, the development of the Engine Control Module ranging from basic integrated circuits to advanced microprocessor based systems reveals its importance in the automobile market. Some of the special features that can be programmed for performance tuning include settings that can be altered for application such as the turbo and the fuel injectors. The Dodge Neon is designed to be a compact car with vibrant performance features; it significantly profits from the features offered by the Engine Control Module to be one of the best for drivers who are looking for quality cars. Altogether, the explanation of Engine Control Module makes one agree with Dodge that the company is right in developing the Neon cars because each car has to be fun to drive and reliable.

Dodge Neon Engine Control Module Parts and Q&A

ECM
R5161104AA
Q: What Steps Should Be Taken Before Replacing the Engine Control Module for a Failed Driver, Control Circuit, or Ground Circuit on Dodge Neon?
A:
Repairers should first confirm related parts and circuits are working correctly before replacing the Pcm if a fault is not noticed due to a double failure. Many issues with Pcm drivers and control circuits result from failing 12-volt pull-ups, drivers and ground sensors inside the circuit. Identifying them can be difficult when only one Dtc is set. Instruction manual If both the Pcm and Skim have to be replaced at once, first put the Vin into the Pcm and then program all of the keys to the new Skim. Each Skis has a secret key special I.d. stored in three places-the Skim, engine controller and transponder chip (ignition key), so the secret key must be reprogrammed into the Pcm if the part is replaced. Program the pinion factor by turning on your ignition, setting the transmission to park or neutral and using the Drbiii(R) to select Theft Alarm, Skim, then Miscellaneous and choose Pcm Replaced. Secure access mode will be activated with the vehicle's four-digit Pin. After two incorrect tries, the system will lock out for one hour and need your ignition in the run position for a full hour before you can try again. Shut off all the accessories and make sure the battery has enough charge; connect a battery charger if it's low. After that, press Enter to put the secret key on the Pcm from the Skim.
ECM
5161105AA
Q: How to Remove and Reinstall an Engine Control Module on Dodge Neon?
A:
Before taking the Engine Control Module out, unplug the negative Battery Cable. After that, take out and replace the air cleaner box. Open and part the electrical connectors on the PCM and then free up the wiring harness dip from its bracket. Afterward, take out the mounting bolts under the PCM bracket, then the nut and screws for the bracket itself. After bracket removal, unclip the PCM while taking out the hard parts of your PL 2.4L SRT-4. After you have removed the assembly, PCM and bracket, return the assembly to its original spot and only screw on the mounting nut loosely. Put the mounting bolts through the PCM bracket from the bottom and make sure to tighten the bolt nut. Add the wiring harness clip to the PCM bracket so that all the connectors for the PCM are the right colors. Link the connector from the PCM to the air cleaner, locking them together and once more place the air cleaner box back into place. Lastly, attach the negative battery cable again.