How to Remove and Replace a Front Brake Disc on Dodge Viper?

Before you start, make sure the vehicle is up and supported. After that, take out the wheel and tire unit. After that, unlock the bolts holding the brake caliper to the steering knuckle. Avoid suspending the brake caliper from the brake hose so you don't damage any of its parts. After removing the brake caliper, attach a piece of mechanics wire to the upper control arm so you can hang the caliper. If you plan to put back the same rotor, first mark a wheel-stud location and the rotor with chalk next to it before you take it off. Just before you finish, remove the brake rotor from the assembly of the hub and the bearing.

How to Service the Rear Brake Disc on Dodge Viper?

To work on the back brake disc, lift the vehicle and prise off the wheel and tire. Avoid getting the caliper piston close to the bore at this point, as only a specific tool can be used to keep the caliper safe. As you hold the anti-rattle spring, take out the rear disc brake shoe retaining pin to avoid injury. Pull out the retaining pin and anti-rattle spring, ensuring the snap ring is not corroded or damaged while you have them out. Pull the outboard brake shoe toward the back of the disc, so it moves over the caliper and raise it out. Now perform the same for the brake shoe on the other side of the main cylinder. Put a mark on the disc and one on a wheel mounting stud and then detach the disc from the hub. With the Spanner, Special Tool 6366, rotate the caliper piston clockwise until completely seated, using needed force. Place the disc in the car with the marked hole lining up with the marked stud hole before tightening the disc. If the disc brake shoes look new, they can be put in whichever rear position you choose, but make sure original ones are replaced in their original location. Install the inboard brake shoe first, then the outboard shoe, placing the anti-rattle spring in place before driving in the retaining pin to prevent hurting yourself. Set up the anti-rattle clip and add the brake assembly retaining pin through the loops in the spring. Place a pin hammer on the drift and hold the cap against the bore while tapping the pin. Assemble the wheels with the tires, holding back on tightening the wheel mounting stud nuts until the chassis and suspension are installed. Once everything is ready, tighten the stud nuts after pre-tightening them to half specification and next to the full required amount of 122 Nm (90 ft. lbs.). Lower the automobile down, then use the brakes several times to set the brake linings and adjust the parking brake. Test the feeling of the brakes by pressing the pedal down before you begin to drive the vehicle; this will remove any foreign matter and get the shoes into proper contact with the lining.

OEM Dodge Viper Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Brake Discs found

View related parts
Dodge Viper Rotor Part Number: 5181459AC
$825.44 MSRP: $1265.00
You Save: $439.56 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Brake Rotor; Rotor Brake
- Replaces: 5181459AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2017 Dodge Viper | 8.4L V10
- 2009-2010 Dodge Viper | 8.4L V10
View related parts
Dodge Viper Rotor Part Number: 68225243AA
$1320.48 MSRP: $2010.00
You Save: $689.52 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Dodge Viper | ACR, GTC, GTS | 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor Part Number: 68225242AA
$1353.63 MSRP: $2055.00
You Save: $701.37 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Brake Rotor; Rotor Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Dodge Viper | ACR, GTC, GTS | 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor Part Number: 68225239AA
$1353.63 MSRP: $2055.00
You Save: $701.37 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Brake Rotor; Rotor Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Dodge Viper | ACR, GTC, GTS | 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor Part Number: 68225244AA
$1364.68 MSRP: $2080.00
You Save: $715.32 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Dodge Viper | ACR, GTC, GTS | 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor, Front Part Number: 68252788AA
$3817.78 MSRP: $5785.00
You Save: $1967.22 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Front; Disc Brake Hardware Kit; Rotor Brake; Brake Rotor
- Position: Front
- Replaces: 68252789AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Dodge Viper | ACR, GTC, GTS | 10 Cyl 8.4 L GAS
- 2015 Dodge Viper | 8.4L V10
View related parts
Dodge Viper Rotor Part Number: 5181464AC
$755.82 MSRP: $1145.00
You Save: $389.18 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor Brake
- Replaces: 5181464AB, 5181464AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2017 Dodge Viper | 8.4L V10
- 2009-2010 Dodge Viper | 8.4L V10
View related parts
Dodge Viper Rotor, Rear Part Number: 5290393AA
$155.22 MSRP: $192.00
You Save: $36.78 (20%)
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Rear; Rotor Brake; Brake Rotor
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017, 2008-2010, 2003-2006 Dodge Viper | ACR, Base, GT, GTC, GTS, SRT-10, SRT-10 ACR | 10 Cyl 8.3 L GAS, 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor, Front Part Number: 5290394AA
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Front; Disc Brake Hardware Kit; Rotor Brake; Brake Rotor
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017, 2008-2010, 2003-2006 Dodge Viper | ACR, Base, GT, GTC, GTS, SRT-10, SRT-10 ACR | 10 Cyl 8.3 L GAS, 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor, Rear Part Number: 68252786AA
$3955.98 MSRP: $5785.00
You Save: $1829.02 (32%)
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Rear; Rotor Brake; Brake Rotor
- Position: Rear
- Replaces: 68252787AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017 Dodge Viper | ACR, GTC, GTS | 10 Cyl 8.4 L GAS
- 2015 Dodge Viper | 8.4L V10
View related parts
Dodge Viper Brake Rotor Part Number: 4642353
Product Specifications
- Other Name: Rotor - Brake; Rotor; Rotor, Rear Brake Vented; Rotor Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-2002 Dodge Viper | ACR, Base, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS
View related parts
Dodge Viper Brake Rotor Part Number: 4642122AC
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Hardware Kit; Rotor
- Replaces: 4642122
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-2002 Dodge Viper | ACR, Base, GT2, GTS, R/T-10 | 10 Cyl 8.0 L GAS, 8.0L V10
View related parts
Dodge Viper Rotor Part Number: 5181462AC
Product Specifications
- Other Name: Rotor - Brake; Brake Rotor; Rotor Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017, 2009-2010 Dodge Viper | ACR, Base, GT, GTC, GTS, SRT-10 ACR | 10 Cyl 8.4 L GAS
View related parts
Dodge Viper Rotor Part Number: 5181463AC
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor Brake
- Replaces: 5181463AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2017 Dodge Viper | ACR, Base, GT, GTC, GTS | 10 Cyl 8.4 L GAS, 8.4L V10
- 2009-2010 Dodge Viper | 8.4L V10

Dodge Viper Brake Disc

Choose OEM Brake Disc that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Brake Disc follows strict manufacturing steps to lock in quality and fit. If your Dodge Viper matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Viper parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Dodge Viper Brake Disc;Brake Pad is one of the vital part that have stood fare the Viper reputation and its qualities. Manufactured solely for numerous Dodge Viper models, this Brake Disc includes powerfully constructed brake pads that have a high friction material for increased stopping capabilities and safe driving. Since wear sensors and indicators have been incorporated into the braking system, the drivers will be informed when to change them leading to increased effectiveness of the system. This is especially true for those individuals who take their vehicles through performance where better stopping power may well be needed on the road. The Dodge Viper Brake Disc kit not only reestablishes, yet enhances the braking system, which includes hardware of clips, springs, and shims that ensure the wear and functioning of the pad is even. The importance of this Brake Disc system therefore is that it is able to leveled off its functionality under conditions such as Prospective High Stress, its tendency to overheat and fade contributing to longer stopping distance. Thus, Dodge Viper Brake Disc is one of the few automotive systems that can be installed on different models of Viper and this aspect makes it genuinely remarkable in today's world of engineering marvels. This system serves to increase the driving comfort while at the same time protecting the driver and the passengers, thus constituting an important aspect of the Dodge Viper series' performance history.

Dodge Viper Brake Disc Parts and Q&A

Rotor
5181464AC
Q: How to Remove and Replace a Front Brake Disc on Dodge Viper?
A:
Before you start, make sure the vehicle is up and supported. After that, take out the wheel and tire unit. After that, unlock the bolts holding the Brake Caliper to the Steering Knuckle. Avoid suspending the brake caliper from the brake hose so you don't damage any of its parts. After removing the brake caliper, attach a piece of mechanics wire to the upper control arm so you can hang the caliper. If you plan to put back the same rotor, first mark a wheel-stud location and the rotor with chalk next to it before you take it off. Just before you finish, remove the brake rotor from the assembly of the hub and the bearing.
Brake Rotor
4642122AC
Q: How to Service the Rear Brake Disc on Dodge Viper?
A:
To work on the back brake disc, lift the vehicle and prise off the wheel and tire. Avoid getting the caliper piston close to the bore at this point, as only a specific tool can be used to keep the caliper safe. As you hold the anti-rattle spring, take out the rear disc brake shoe retaining pin to avoid injury. Pull out the retaining pin and anti-rattle spring, ensuring the snap ring is not corroded or damaged while you have them out. Pull the outboard brake shoe toward the back of the disc, so it moves over the caliper and raise it out. Now perform the same for the brake shoe on the other side of the main cylinder. Put a mark on the disc and one on a wheel mounting stud and then detach the disc from the hub. With the Spanner, Special Tool 6366, rotate the caliper piston clockwise until completely seated, using needed force. Place the disc in the car with the marked hole lining up with the marked stud hole before tightening the disc. If the disc brake shoes look new, they can be put in whichever rear position you choose, but make sure original ones are replaced in their original location. Install the inboard brake shoe first, then the outboard shoe, placing the anti-rattle spring in place before driving in the retaining pin to prevent hurting yourself. Set up the anti-rattle clip and add the brake assembly retaining pin through the loops in the spring. Place a pin hammer on the drift and hold the cap against the bore while tapping the pin. Assemble the wheels with the tires, holding back on tightening the wheel mounting stud nuts until the chassis and suspension are installed. Once everything is ready, tighten the stud nuts after pre-tightening them to half specification and next to the full required amount of 122 Nm (90 ft. lbs.). Lower the automobile down, then use the brakes several times to set the brake linings and adjust the parking brake. Test the feeling of the brakes by pressing the pedal down before you begin to drive the vehicle; this will remove any foreign matter and get the shoes into proper contact with the lining.