How to replace a Neutral Safety Switch on Jeep Cherokee?

First of all, drain the fluid before replacing the Neutral Safety Switch, you must ensure the correct gearshift lever position. After installation, test for continuity and check fluid level. For a four-speed transmission, check for continuity and replace if necessary. To replace, remove the connector, washer tabs, nut, and bolt. Adjust the shift lever and switch position, tighten the nut and bolt, and align the neutral standard line.

How to test and replace a Neutral Safety Switch on Jeep Wrangler?

The neutral safety switch and back-up light switches are combined into one unit, featuring three terminals with the neutral switch positioned in the center. A ground for the starter solenoid circuit is provided through the shift lever only in the Neutral and Park positions. Begin by raising the vehicle and securing it on jackstands, then detach the electrical connector from the neutral safety switch, which screws into the housing and contacts the internal shaft lever, and test the switch for continuity; continuity should exist between the center terminal and transmission case only when the shift lever is in Neutral and Park. If the switch appears faulty, check the shift linkage before replacing it. Before replacing the switch, place a container underneath to catch any transmission fluid, then remove the switch and allow the fluid to drain. With the shift lever in Park or Neutral, check the lever finger position and alignment with the switch opening. Install the switch and seal, tightening it to the specified torque, then test for continuity and reconnect the electrical connector. Finally, lower the vehicle and check the transmission fluid level, adding the specified fluid as necessary.

OEM Jeep Neutral Safety Switch

Transmission Range Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Neutral Safety Switchs found

View related parts
Jeep Range Sensor Part Number: 68197332AA
$208.47 MSRP: $311.00
You Save: $102.53 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Transmission Range; Sensor Transmission Range
Fits the following Jeep Models:
- Cherokee | 2014-2019 | 75th Anniversary, Altitude, High Altitude, Latitude, Latitude Plus, Limited, Overland, Sport, Trailhawk, Trailhawk Elite | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
- Compass | 2019 | Altitude, High Altitude, Latitude, Limited, Sport, Trailhawk, Upland | 4 Cyl 2.4 L GAS
- Renegade | 2015-2017 | 75th Anniversary, Latitude, Sport | 4 Cyl 1.4 L GAS
View More
View related parts
Jeep Range Sensor Part Number: 68197333AA
$310.44 MSRP: $462.00
You Save: $151.56 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Transmission Range; Sensor Transmission Range
Fits the following Jeep Models:
- Compass | 2017-2018 | Latitude, Limited, Sport, Trailhawk | 4 Cyl 2.4 L GAS
View related parts
Jeep Range Sensor Part Number: 68425024AA
$87.81 MSRP: $130.00
You Save: $42.19 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Transmission Range; Sensor Transmission Range
Fits the following Jeep Models:
- Cherokee | 2020-2023 | 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Trailhawk, Trailhawk Elite, Upland, X | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
- Compass | 2020-2022 | 80th Anniversary, Altitude, High Altitude, Latitude, Latitude Lux, Limited, Red, Sport, Trailhawk, Upland | 4 Cyl 2.4 L GAS
- Renegade | 2018-2023 | 80th Anniversary, Altitude, High Altitude, Islander, Jeepster, Latitude, Limited, Red, Sport, Trailhawk, Upland | 4 Cyl 1.3 L GAS, 4 Cyl 1.4 L GAS, 4 Cyl 2.4 L GAS
View More
View related parts
Jeep Range Sensor Part Number: 68425025AA
$234.26 MSRP: $356.00
You Save: $121.74 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Transmission Range; Sensor Transmission Range
Fits the following Jeep Models:
- Renegade | 2018-2023 | 80th Anniversary, Altitude, High Altitude, Islander, Jeepster, Latitude, Limited, Red, Sport, Trailhawk, Upland | 4 Cyl 1.3 L GAS, 4 Cyl 1.4 L GAS, 4 Cyl 2.4 L GAS
View related parts
Jeep Range Sensor Part Number: 68617974AA
$60.32 MSRP: $90.30
You Save: $29.98 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Position
Fits the following Jeep Models:
- Compass | 2023-2024 | Altitude, High Altitude, Latitude, Latitude Lux, Limited, Red, Sport, Trailhawk | 4 Cyl 2.0 L GAS
View related parts
Jeep Neutral Safety Switch Part Number: 56028181AC
Product Specifications
- Other Name: Switch - Neutral, Safety, Back Up
Fits the following Jeep Models:
- Cherokee | 2000-2001 | Classic, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
- Grand Cherokee | 1998-2002 | 5.9 Limited, Laredo, Limited, Overland, Sport, TSi | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Wrangler | 2000-2002 | SE, Sahara, Sport, X | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View More
View related parts
Jeep Neutral Safety Switch Part Number: 3747361AB
Product Specifications
- Other Name: Switch - Neutral Safety, Back Up; Range Sensor; Back-Up Switch
- Replaces: 3747361, P5007747, P5007747AB
Fits the following Jeep Models:
- Cherokee | 1992-1997 | Base, Briarwood, Classic, Country, Laredo, Limited, SE, Sport | 2.5L L4, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
- Comanche | 1991-1992 | Base, Eliminator, Pioneer | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
- Grand Cherokee | 2000-2004, 1993-1997 | Base, Laredo, Limited, Orvis, Overland, SE, Special Edition, TSi | 4.0L L6, 4.7L V8, 5.2L V8, 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, EKY
- Grand Wagoneer | 1993 | 5.2L V8
- Wrangler | 1997-1999, 1991-1995 | Base, Islander, Renegade, S, Sahara, SE, Sport | 2.5L L4, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View More
View related parts
Jeep Neutral Safety Switch Part Number: 68404600AB
$201.67 MSRP: $301.00
You Save: $99.33 (33%)
Product Specifications
- Other Name: Switch - Neutral Safety; Switch Neutral Safety
- Replaces: 68404600AA
Fits the following Jeep Models:
- Wrangler | 2018-2025 | 80th Anniversary, Freedom, Islander, Rubicon, Rubicon X, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Altitude 4xe, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Rubicon 392, Unlimited Rubicon 4xe, Unlimited Rubicon X, Unlimited Rubicon X 4xe, Unlimited Sahara, Unlimited Sahara 4xe, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Sport S 4xe, Unlimited Willys, Unlimited Willys 4xe, Unlimited Willys Sport, Willys, Willys Sport | 3.6L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.4 L GAS
View related parts
Jeep Neutral Safety Switch Part Number: 4882173
Product Specifications
- Other Name: Switch - Neutral, Safety, Back Up; Switch Neutral Safety, Back Up
Fits the following Jeep Models:
- Cherokee | 1997-2001 | Classic, Country, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
- Wrangler | 1997-2001 | SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Neutral Safety Switch

OEM parts sourced directly from Jeep deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Jeep Neutral Safety Switch for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Jeep's Neutral Safety Switch makes it so that the starter only energizes when it is safe. Over the decades, Jeep has established an anywhere reputation rooted in toughness, open air fun and simple mechanics. Contemporary boxed frames are enhanced with digital dashboards, over the air updates and the Selec-Terrain dial that changes traction maps quick. Long drives are comfortable, assisted by voice control, smartphone mirroring and safety aids. However, boulders are of no consequence due to the high clearance along with stout arches. A close-knit community of Jeep owners shares tips and parts to reinforce no-nonsense charm, so whether you're downtown or in the deep woods, the Jeep keeps curiosity moving. The cabins can be washed without any hassle, while drain plugs below the floor allow mud and river water to exit quickly. Additionally, the fold-flat rear seats can carry camping gear, allowing owners to go chasing storms. In every auto, the Neutral Safety Switch bolts to the shaft of the selector, closing only in Park or Neutral, so the computer knows when the engine will start. If the circuit remains open, the starter current does not flow and the engine cannot push the vehicle forward. This part of a gearbox sensor is only a two state contact, but it is sealed against dirt and water. A silent key turn indicates loss of continuity, which is why many fans keep a spare Neutral Safety Switch in the glovebox. Due to the commonality of wiring and logic, a modern Jeep not cranking is often a tired Neutral Safety Switch, which can be easily diagnosed across the broader Jeep line.

Jeep Neutral Safety Switch Parts and Q&A

Neutral Safety Switch
56028181AC
Q: How to replace a Neutral Safety Switch on Jeep Cherokee?
A:
First of all, drain the fluid before replacing the Neutral Safety Switch, you must ensure the correct gearshift lever position. After installation, test for continuity and check fluid level. For a four-speed transmission, check for continuity and replace if necessary. To replace, remove the connector, washer tabs, nut, and bolt. Adjust the shift lever and switch position, tighten the nut and bolt, and align the neutral standard line.
Neutral Safety Switch
3747361AB
Q: How to test and replace a Neutral Safety Switch on Jeep Wrangler?
A:
The neutral safety switch and back-up light switches are combined into one unit, featuring three terminals with the neutral switch positioned in the center. A ground for the starter solenoid circuit is provided through the shift lever only in the Neutral and Park positions. Begin by raising the vehicle and securing it on jackstands, then detach the electrical connector from the neutral safety switch, which screws into the housing and contacts the internal shaft lever, and test the switch for continuity; continuity should exist between the center terminal and transmission case only when the shift lever is in Neutral and Park. If the switch appears faulty, check the shift linkage before replacing it. Before replacing the switch, place a container underneath to catch any transmission fluid, then remove the switch and allow the fluid to drain. With the shift lever in Park or Neutral, check the lever finger position and alignment with the switch opening. Install the switch and seal, tightening it to the specified torque, then test for continuity and reconnect the electrical connector. Finally, lower the vehicle and check the transmission fluid level, adding the specified fluid as necessary.