How to Properly Service and Repair a Brake Line on 2000 Dodge Dakota?

In brake service and repair, use a preformed metal brake tube and, if the factory parts are not available, install a double-wall steel tube just for emergencies. To stop metal brake tubes from kinking or twisting, special tools are necessary and to make a double inverted flare or ISO flare, specific flaring tools are required. First, trim off the neglected pipe with a Tubing Cutter and file the cut areas to guarantee a correct flare. Fit a new replacement tube nut onto the straight tube, put the tube into the flaring tool and put the gauge form over it. Insert the tubing into the flaring tool up until it reaches its recessed notch that matches your tube diameter and tighten the bar on the tube. Put the plug of the gauge into the tube, turn the compression disc to cover the gauge and set the tapered flaring screw into the center of the disc. Clamp the plug gauge down onto the tool jaws by turning the handle next to it. After that, use the tool to finish the inverted flare. Snap-On Flaring Tool TFM-428 should be used or an equivalent is required for ISO flaring. Snip off the dented area with a Tubing Cutter, clean up any burs on the inside and attach the tube nut to the tube. Place the tube into the flaring tool so the last piece of the end aligns with the last part on the tool bar and tighten the tool bar down. Attach the right size adaptor to the flaring tool yoke screw, grease it, ensure it is lined up at the yoke screw end of the tube and turn the yoke screw until the adaptor is firmly on the tool bar.

OEM 2000 Dodge Dakota Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Lines found

View related parts
2000 Dodge Dakota Flex Hose, Front Driver Side Part Number: 52009879AC
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Front Left; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Front Driver Side
- Item Weight: 1.70 Pounds
- Item Dimensions: 17.4 x 10.8 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52009879AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2000 Dodge Dakota Flex Hose, Front Passenger Side Part Number: 52009878AC
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Front Right; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Front Passenger Side
- Item Weight: 1.70 Pounds
- Item Dimensions: 15.7 x 9.6 x 1.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52009878AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2000 Dodge Dakota Flex Hose, Front Driver Side Part Number: 52008992
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Front Left, Front Right; Brake Hose; Brake Line; Hose Brake 11; Hose Brake; Hydraulic Hose
- Position: Front Driver Side
- Item Weight: 1.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52008992
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
2000 Dodge Dakota Flex Hose, Rear Center Part Number: 52008984AE
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Rear Center; Brake Hose; Brake Line; Hose Brake; Hydraulic Hose
- Position: Rear Center
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.3 x 6.1 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52008984AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Dakota Submodels:
- Base, R/T, SLT, SXT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
2000 Dodge Dakota Flex Hose, Front Passenger Side Part Number: 52008981
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Hose, Front Left, Front Right; Brake Hose; Brake Line; Hose Brake 11; Hose Brake; Hydraulic Hose
- Position: Front Passenger Side
- Item Weight: 2.30 Pounds
- Item Dimensions: 4.1 x 8.1 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52008981
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
2000 Dodge Dakota Tube Assembly Part Number: 52009894AC
Product Specifications
- Other Name: Line - Brake; Brake Hydraulic Line; Brake Line; Tube Brake
- Item Weight: 1.50 Pounds
- Item Dimensions: 25.3 x 5.6 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52009894AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Dodge Dakota Submodels:
- Base, R/T, SLT, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS

2000 Dodge Dakota Brake Line Parts and Q&A

Q: How to Properly Service and Repair a Brake Line on 2000 Dodge Dakota?
A: In brake service and repair, use a preformed metal brake tube and, if the factory parts are not available, install a double-wall steel tube just for emergencies. To stop metal brake tubes from kinking or twisting, special tools are necessary and to make a double inverted flare or ISO flare, specific flaring tools are required. First, trim off the neglected pipe with a Tubing Cutter and file the cut areas to guarantee a correct flare. Fit a new replacement tube nut onto the straight tube, put the tube into the flaring tool and put the gauge form over it. Insert the tubing into the flaring tool up until it reaches its recessed notch that matches your tube diameter and tighten the bar on the tube. Put the plug of the gauge into the tube, turn the compression disc to cover the gauge and set the tapered flaring screw into the center of the disc. Clamp the plug gauge down onto the tool jaws by turning the handle next to it. After that, use the tool to finish the inverted flare. Snap-On Flaring Tool TFM-428 should be used or an equivalent is required for ISO flaring. Snip off the dented area with a Tubing Cutter, clean up any burs on the inside and attach the tube nut to the tube. Place the tube into the flaring tool so the last piece of the end aligns with the last part on the tool bar and tighten the tool bar down. Attach the right size adaptor to the flaring tool yoke screw, grease it, ensure it is lined up at the yoke screw end of the tube and turn the yoke screw until the adaptor is firmly on the tool bar.