How to Remove and Install a Speed Sensor in 4WD and 2WD on 2000 Jeep Wrangler?

The Vehicle Speed Sensor (VSS) sits on the speedometer pinion gear adapter and is attached to the transfer case extension on 4WD vehicles and the extension housing of the transmission on 2WD models. You should raise and support the vehicle, then press and slide the tab and secondary release lock to take out the electrical connector from the sensor. After that, take the bolt out of the sensor mount and pull the sensor straight out of the pinion gear adapter, without taking the adapter away from the transmission. Clean the inside of the speedometer pinion gear adapter, add in the sensor and fasten it with the bolt, making sure the sensor is fully on the adapter before tightening to 2.2 N.m (20 in. lbs.) torque. Connect the electrical wire back to the sensor after you have cleaned it.

OEM 2000 Jeep Wrangler Speed Sensor

Speed Control Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Speed Sensors found

View related parts
2000 Jeep Wrangler Vehicle Speed Sensor Part Number: 56027905
Product Specifications
- Other Name: Sensor - Vehicle Speed; Sensor Vehicle Speed
- Item Weight: 0.50 Pounds
- Item Dimensions: 1.6 x 1.5 x 3.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56027905
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Wrangler Crankshaft Position Sensor Part Number: 56027868AD
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Vehicle Speed Sensor
- Replaces: 4897321AA, 56027868AC, 4897189AA, 4897321AB
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56027868AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2000 Jeep Wrangler Submodels:
- Sahara, Sport, X | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Wrangler ABS Sensor, Rear Driver Side Part Number: 56027729AB
Product Specifications
- Other Name: Sensor - Anti-Lock Brakes; ABS Wheel Speed Sensor, Rear Left; Rear Speed Sensor
- Position: Rear Driver Side
- Replaces: 56027729
- Item Weight: 1.20 Pounds
- Item Dimensions: 12.2 x 1.8 x 1.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56027729AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 2.5L L4, 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Wrangler ABS Sensor Part Number: 52005932AB
Product Specifications
- Other Name: Sensor - Anti-Lock Brakes; Rear Speed Sensor
- Replaces: 52005932
- Item Weight: 0.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52005932AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Wrangler Submodels:
- SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Wrangler ABS Sensor, Front Driver Side Part Number: 56027727AB
Product Specifications
- Other Name: Sensor - Anti-Lock Brakes; ABS Wheel Speed Sensor, Front Left, Front Right; ABS Wheel Speed Sensor; Front Speed Sensor
- Position: Front Driver Side
- Replaces: 56027727
- Item Weight: 0.80 Pounds
- Item Dimensions: 10.2 x 2.3 x 0.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56027727AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 2.5L L4, 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Wrangler ABS Sensor Part Number: 52005933AB
Product Specifications
- Other Name: Sensor - Anti-Lock Brakes; Anti-Lock Braking System Sensor; ABS Wheel Speed Sensor; Rear Speed Sensor
- Replaces: 52005933
- Item Weight: 0.50 Pounds
- Item Dimensions: 53.8 x 1.6 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 52005933AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Wrangler Submodels:
- SE, Sahara, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2000 Jeep Wrangler ABS Sensor, Rear Passenger Side Part Number: 56027728AB
Product Specifications
- Other Name: Sensor - Anti-Lock Brakes; ABS Wheel Speed Sensor, Rear Right; Anti-Lock Braking System Sensor; ABS Wheel Speed Sensor; Rear Speed Sensor
- Position: Rear Passenger Side
- Replaces: 56027728
- Item Weight: 0.80 Pounds
- Item Dimensions: 11.6 x 9.3 x 0.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56027728AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2000 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 2.5L L4, 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS

2000 Jeep Wrangler Speed Sensor Parts and Q&A

Q: How to Remove and Install a Speed Sensor in 4WD and 2WD on 2000 Jeep Wrangler?
A: The Vehicle Speed Sensor (VSS) sits on the speedometer pinion gear adapter and is attached to the transfer case extension on 4WD vehicles and the extension housing of the transmission on 2WD models. You should raise and support the vehicle, then press and slide the tab and secondary release lock to take out the electrical connector from the sensor. After that, take the bolt out of the sensor mount and pull the sensor straight out of the pinion gear adapter, without taking the adapter away from the transmission. Clean the inside of the speedometer pinion gear adapter, add in the sensor and fasten it with the bolt, making sure the sensor is fully on the adapter before tightening to 2.2 N.m (20 in. lbs.) torque. Connect the electrical wire back to the sensor after you have cleaned it.