How to Service and Repair a 4X2 Front Wheel Speed Sensor on 2001 Dodge Dakota?

You should raise and support the 4X2 vehicle before fixing the front Wheel Speed Sensor. Unscrew the bolt connecting the sensor to the steering knuckle and then pull off the wire clamps from the control arm and inner fender panel. In the engine compartment, remove the sensor wire from the harness and take out the sensor. Set the sensor in the knuckle and lift it into position, using the sensor bolts to attach it and tighten them to 21 Nm (190 inch lbs.). Screw the sensor wire retaining clamps onto the control arm and fender panel and plug the sensor wire into the harness connector close to the engine. Keep the wire away from any moving or very hot parts underneath the hood. Also, check the wire by moving the steering wheel back and forth to confirm everything is clear from the steering and suspension system, then take out the supports and lower the car. Since using substitutes isn't allowed, you must always get factory replacement parts for the bolts that secure the front sensor.

OEM 2001 Dodge Dakota Speed Sensor

Speed Control Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Speed Sensors found

View related parts
2001 Dodge Dakota ABS Sensor, Rear Part Number: 56028187AE
$64.56 MSRP: $96.75
You Save: $32.19 (34%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Wheel Speed; ABS Wheel Speed Sensor, Rear; Vehicle Speed Sensor; Speed Sensor; Rear Speed Sensor; Sensor Wheel Speed; ABS Wheel Speed Sensor
- Position: Rear
- Replaces: 56028187AD
- Item Weight: 0.50 Pounds
- Item Dimensions: 1.9 x 2.6 x 3.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 56028187AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Dakota Submodels:
- Base, R/T, SLT, SLT Plus, SXT, Sport, Sport Plus | 2.5L L4, 3.7L V6, 3.9L V6, 4 Cyl 2.5 L GAS, 4.7L V8, 5.2L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2001 Dodge Dakota Speed Sensor, Front Passenger Side Part Number: 5016338AB
$91.31 MSRP: $105.00
You Save: $13.69 (14%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Wheel Speed; ABS Wheel Speed Sensor, Front Right; ABS Sensor; Front Speed Sensor
- Position: Front Passenger Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 7.3 x 6.7 x 3.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5016338AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Dakota Submodels:
- Base, R/T, SLT, SLT Plus, SXT, Sport, Sport Plus | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
2001 Dodge Dakota Speed Sensor, Front Driver Side Part Number: 5016339AB
$103.36 MSRP: $119.00
You Save: $15.64 (14%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Wheel Speed; ABS Wheel Speed Sensor, Front Left; ABS Sensor; Front Speed Sensor
- Position: Front Driver Side
- Item Weight: 0.80 Pounds
- Item Dimensions: 7.6 x 6.6 x 3.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5016339AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2001 Dodge Dakota Submodels:
- Base, R/T, SLT, SLT Plus, SXT, Sport, Sport Plus | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS

2001 Dodge Dakota Speed Sensor Parts and Q&A

Q: How to Service and Repair a 4X2 Front Wheel Speed Sensor on 2001 Dodge Dakota?
A: You should raise and support the 4X2 vehicle before fixing the front Wheel Speed Sensor. Unscrew the bolt connecting the sensor to the steering knuckle and then pull off the wire clamps from the control arm and inner fender panel. In the engine compartment, remove the sensor wire from the harness and take out the sensor. Set the sensor in the knuckle and lift it into position, using the sensor bolts to attach it and tighten them to 21 Nm (190 inch lbs.). Screw the sensor wire retaining clamps onto the control arm and fender panel and plug the sensor wire into the harness connector close to the engine. Keep the wire away from any moving or very hot parts underneath the hood. Also, check the wire by moving the steering wheel back and forth to confirm everything is clear from the steering and suspension system, then take out the supports and lower the car. Since using substitutes isn't allowed, you must always get factory replacement parts for the bolts that secure the front sensor.