Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us

OEM 2008 Chrysler Pacifica ABS Control Module

Anti Lock Brake Control Module
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 ABS Control Modules found

  • 2008 Chrysler Pacifica ABS Control Module - 5175522AC
    2008 Chrysler Pacifica ABS Control Module - 5175522AC
    2008 Chrysler Pacifica ABS Control Module Diagram - 5175522AC
    View related parts

    2008 Chrysler Pacifica Control Module Part Number: 5175522AC

    Product Specifications
    • Other Name: Module - ABS; ABS Control Module; Module Anti-Lock Brakes
    • Replaces: 5175522AA
    • Item Weight: 2.30 Pounds
    • Item Dimensions: 3.3 x 4.6 x 6.2 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 5175522AC
    • Warranty: This genuine part is guaranteed by Mopar's factory warranty.
    More Info
    Fits the following 2008 Chrysler Pacifica Submodels:
    • Base, LX, Limited, Touring | 3.8L V6, 4.0L V6, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
  • 2008 Chrysler Pacifica ABS Control Module - 5175520AC
    2008 Chrysler Pacifica ABS Control Module - 5175520AC
    2008 Chrysler Pacifica ABS Control Module Diagram - 5175520AC
    View related parts

    2008 Chrysler Pacifica Modulator Part Number: 5175520AC

    Product Specifications
    • Other Name: Module - Anti-Lock Brake; ABS Modulator Valve; ABS Control Module; Control Unit Anti-Lock Brake
    • Replaces: 5175520AA
    • Item Weight: 6.30 Pounds
    • Item Dimensions: 9.5 x 7.5 x 6.1 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 5175520AC
    • Warranty: This genuine part is guaranteed by Mopar's factory warranty.
    More Info
    Fits the following 2008 Chrysler Pacifica Submodels:
    • Base, LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS

2008 Chrysler Pacifica ABS Control Module Parts and Q&A

  • Q: How to Install an ABS Control Module Correctly on 2008 Chrysler Pacifica?
    A: Check the seal around the ABM's mating edge as the first step in installing the ABM. Carefully clean away any dirt or dust from where the two parts meet. Don't harm the pressure sensor when you install it or it will require you to get a replacement HCU. Put the ABM solenoids and pump/motor wires in the spaces for the HCU valves and wires and safely slide the ABM onto the HCU. Place four screws into the ABM and tighten them to 6 Nm (53 in. lbs.) on the HCU. Before the connector goes on the ABM socket, raise the release lever all the way up, place the connector on the ABM and push it down until the lever locks. After that, install the wiring connector from the ABM into its docking point and then link the negative battery cable to the post on the battery. The scan tool should be connected to start the ABM, remove any existing faults, do the ABS Verification Test and perform a road test on the vehicle.

Related 2008 Chrysler Pacifica Parts

Alternate Year Models

+
2007 Chrysler Pacifica ABS Control Module