How to Safely Remove and Replace a Brake Caliper on 2008 Chrysler Pacifica?

Be sure that both inner and outer brake pads have intact adhesive on their noise suppression gaskets before removing or replacing the brake caliper; if it is not there or damaged, change the brake pads. Gently place the disc brake caliper on the brake pads inside the brake caliper adapter, so you do not hurt the boots on the caliper guide pins. Square up the caliper guide pin bolt holes to the guide pins and then insert the bolts, making sure the upper bolt (nearest to the bleeder screw) is tightened to 43 Nm (32 ft. lbs.) before turning to the same tension level on the lower bolt. Install the banjo bolt on the brake hose, put new washers on each side of the fitting and thread the bolt into the caliper, tightening it with 47 Nm (35 ft. lbs.) force. Next, put in the tire and wheel assembly and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.), then lower your car and take out the brake pedal holding tool. Connection the (-) battery cable hook and make sure to bleed the hydraulic system as necessary, too. Ultimately, drive around for a bit, making stops along the way to reduce foreign materials and set the brake pads correctly.

OEM 2008 Chrysler Pacifica Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Calipers found

View related parts
2008 Chrysler Pacifica Caliper, Front Passenger Side Part Number: 68032692AA
$72.79 MSRP: $105.00
You Save: $32.21 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Front Right; Caliper Disc Brake; Brake Caliper
- Position: Front Passenger Side
- Item Weight: 12.20 Pounds
- Item Dimensions: 9.8 x 7.1 x 4.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68032692AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Chrysler Pacifica Submodels:
- LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Chrysler Pacifica Caliper, Rear Driver Side Part Number: 5114441AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Left; Caliper Disc Brake; Brake Caliper
- Position: Rear Driver Side
- Item Weight: 5.90 Pounds
- Item Dimensions: 7.4 x 5.4 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5114441AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Chrysler Pacifica Submodels:
- Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Chrysler Pacifica Caliper, Front Driver Side Part Number: 68032693AA
Product Specifications
- Other Name: Disc Brake; Disc Brake Caliper, Front Left; Caliper Disc Brake; Brake Caliper
- Position: Front Driver Side
- Item Weight: 13.80 Pounds
- Item Dimensions: 10.0 x 7.2 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68032693AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Chrysler Pacifica Submodels:
- LX, Limited, Touring | 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Chrysler Pacifica Caliper, Rear Passenger Side Part Number: 5114440AA
Product Specifications
- Other Name: Caliper - Disc Brake; Disc Brake Caliper, Rear Right; Caliper Disc Brake; Brake Caliper
- Position: Rear Passenger Side
- Item Weight: 5.80 Pounds
- Item Dimensions: 5.1 x 5.2 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5114440AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2008 Chrysler Pacifica Submodels:
- Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS

2008 Chrysler Pacifica Brake Caliper Parts and Q&A

Q: How to Safely Remove and Replace a Brake Caliper on 2008 Chrysler Pacifica?
A: Be sure that both inner and outer brake pads have intact adhesive on their noise suppression gaskets before removing or replacing the brake caliper; if it is not there or damaged, change the brake pads. Gently place the disc brake caliper on the brake pads inside the brake caliper adapter, so you do not hurt the boots on the caliper guide pins. Square up the caliper guide pin bolt holes to the guide pins and then insert the bolts, making sure the upper bolt (nearest to the bleeder screw) is tightened to 43 Nm (32 ft. lbs.) before turning to the same tension level on the lower bolt. Install the banjo bolt on the brake hose, put new washers on each side of the fitting and thread the bolt into the caliper, tightening it with 47 Nm (35 ft. lbs.) force. Next, put in the tire and wheel assembly and tighten the wheel mounting nuts to 135 Nm (100 ft. lbs.), then lower your car and take out the brake pedal holding tool. Connection the (-) battery cable hook and make sure to bleed the hydraulic system as necessary, too. Ultimately, drive around for a bit, making stops along the way to reduce foreign materials and set the brake pads correctly.