How to Service and Repair a Power Steering Pump on Chrysler Town & Country?

Turn off the engine first, then check that Mopar® Power Steering Fluid is used to check the fluid level and avoid spilling automatic transmission fluid. The temperature in the fluid should read "Cold Range" between 21°C and 27°C or 70°F and 80°F. Before you take off the cap, clean the filler area, top up the fluid reservoir in the pump and let the fluid settle for around two minutes. Fire up the engine and let it run just a few seconds, so you know when to add fluid, until the fluid level remains the same while running. Pass the front wheels over a pair of blocks, begin the engine, then gently and softly move the steering wheel to reach the stops. Include power steering fluid when necessary. Make sure the car is on steady ground and slowly steer the car from loose to tight, followed by turning off the car and inspecting the fluid. Should the fluid become extremely foamy, let the vehicle steady for a few minutes and then try again.

How to Install a Power Steering Pump on a 3.3L/3.8L Engine on Chrysler Town & Country?

To perform the installation, put the pump onto the engine and fasten it with three bolts, tightening them to 23 Nm (17 ft. lbs.) from the openings in the pulley. After that, fit the accessory drive belt. Replace the O-ring at the hose's end and lubricate it with clean power steering fluid before you connect the hose. Put the pressure hose into the pump's fitting, secure it with the tube nut and tighten it to 31 Nm (23 ft. lbs.). Put the fluid supply hose on the pump fitting and fasten it with a clamp. After that, attach the negative battery cable to its post and refill and bleed the power steering system. The last step is to check for leaks.

OEM Chrysler Town & Country Power Steering Pump

Power Steering Pump Unit

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Power Steering Pumps found

View related parts
Chrysler Town & Country Power Steering Pump Part Number: 5151727AD
$306.35 MSRP: $454.00
You Save: $147.65 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump - Power Steering; Pump Power Steering; Pump
- Replaces: 5151727AC, RL151727AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chrysler Town & Country | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: 4743060AE
$262.36 MSRP: $394.00
You Save: $131.64 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump - Power Steering
- Replaces: 4743060AF, 4743060AD, 4743060AC, 4743060AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: 4721439AB
$878.95 MSRP: $1325.00
You Save: $446.05 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump - Power Steering; Pump Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | LX, Limited, Touring, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: 4470314
$173.87 MSRP: $220.41
You Save: $46.54 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Power Steering; Pump; Pump, Power Steering W/Standard (Saginaw); Pump, Assembly Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990, 1984-1988 Chrysler Town & Country | Base, Mark Cross | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: 5274131
Product Specifications
- Other Name: Packing Steering; Pump, Assembly Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991 Chrysler Town & Country | Base | 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: 4470266
Product Specifications
- Other Name: Pump, Assembly Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: R4470275
Product Specifications
- Other Name: Pump - Power Steering; Pump, Power Steering W/Standard (Saginaw); Pump, Assembly Power Steering
- Replaces: 4470275
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | 3.0L V6, 3.3L V6
- 1988 Chrysler Town & Country | Base | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
View related parts
Chrysler Town & Country Power Steering Pump Part Number: R5274132
Product Specifications
- Other Name: Pump - Power Steering; Pump, Assembly Power Steering
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1995 Chrysler Town & Country | Base | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS

Chrysler Town & Country Power Steering Pump

Choose OEM Power Steering Pump that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Power Steering Pump follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Power Steering Pump in Chrysler Town & Country is a critical component, which is used to translate energy from the engine to hydraulic power so as to ease the process of steering. This pump produces the fluid pressure that helps the driver control movement of the automobile especially when in slow motion or even at rest. The pump is belt driven from the engine crankshaft and contains either an internal or external fluid reservoir. Through the years, Chrysler Town & Country has incorporated a number of types of Power Steering Pumps which include hydraulic means which retain physical link between the steering wheel and wheel. While most cars use hydraulic system, it is possible for the car to possess an electronic system that regulates the assist depending on the speed of the car. Some of the most frequent problems associated with the Power Steering Pump are leakage, loud noises, and irregular steering help, this may require one to inspect or replace to provide the premier assistance to the steering.

Chrysler Town & Country Power Steering Pump Parts and Q&A

Power Steering Pump
4743060AE
Q: How to Service and Repair a Power Steering Pump on Chrysler Town & Country?
A:
Turn off the engine first, then check that Mopar® Power Steering Fluid is used to check the fluid level and avoid spilling automatic transmission fluid. The temperature in the fluid should read "Cold Range" between 21°C and 27°C or 70°F and 80°F. Before you take off the cap, clean the filler area, top up the fluid reservoir in the pump and let the fluid settle for around two minutes. Fire up the engine and let it run just a few seconds, so you know when to add fluid, until the fluid level remains the same while running. Pass the front wheels over a pair of blocks, begin the engine, then gently and softly move the Steering Wheel to reach the stops. Include power steering fluid when necessary. Make sure the car is on steady ground and slowly steer the car from loose to tight, followed by turning off the car and inspecting the fluid. Should the fluid become extremely foamy, let the vehicle steady for a few minutes and then try again.
Power Steering Pump
4721439AB
Q: How to Install a Power Steering Pump on a 3.3L/3.8L Engine on Chrysler Town & Country?
A:
To perform the installation, put the pump onto the engine and fasten it with three bolts, tightening them to 23 Nm (17 ft. lbs.) from the openings in the pulley. After that, fit the accessory Drive Belt. Replace the O-ring at the hose's end and lubricate it with clean power steering fluid before you connect the hose. Put the pressure hose into the pump's fitting, secure it with the tube nut and tighten it to 31 Nm (23 ft. lbs.). Put the fluid supply hose on the pump fitting and fasten it with a clamp. After that, attach the negative battery cable to its post and refill and bleed the power steering system. The last step is to check for leaks.