How to Install the Front Timing Cover and Its Components on Chrysler Town & Country?

When installing the belt cover, wash and dry both the engine block holes and all the timing bolts to ensure there is no oil and be sure to add thread sealant to the bolts that connect to the oil pump. Start with the front timing belt cover and afterwards set up the upper engine mount. After that, attach the fuel supply line to the fuel rail and place the air cleaner housing. Remove the floor jack and raise the vehicle, then screw in the power steering pump, tightening them up to 23 Nm (200 lbs. in.). Next, fit the crankshaft damper, ensure the accessory drive belt tensioner is in place and then tighten the fastener to 28 Nm (250 in. lbs.). Connect the accessory drive belt, drive your vehicle down onto the ground and then complete by connecting the negative battery cable.

How to remove a timing cover on Chrysler Town & Country?

Before removing the engine timing cover, isolate the negative battery cable and drain out the cooling system. Lift the car on a motor hoist and then remove all the oil from its engine. Take out the right front tire and wheel assembly and then remove the inner splash shield located there. Following that, remove the oil pan and the oil pick-up tube. Remove the accessory drive belt and then remove one bolt and three nuts to adjust the A/C compressor. Disconnect the vibration damper for the crankshaft and take off the heater return hose from its place on the timing chain case or water pump inlet tube if your engine has an oil cooler. Take out the lower radiator hose and the camshaft position sensor from the timing chain cover. Remove the engine mount on the right side and loosen the bolt from the power steering line support bracket. Take off two bolts, a nut and then another bracket, plus yet another bolt and nut. Rearrange the generator by taking out the generator's bolts, then take out three mounting bolts from below the pump pulley to move the power steering pump. After removing the bolt and tensioner, remove both the bolt and the idler pulley on the accessory drive belt. With the water pump removed, get rid of the timing chain cover fasteners and then remove the timing chain cover.

OEM Chrysler Town & Country Timing Cover

Engine Timing Cover

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Timing Covers found

View related parts
Chrysler Town & Country Timing Cover, Lower Outer Part Number: 4892138AB
$217.86 MSRP: $327.00
You Save: $109.14 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Timing Case; Engine Timing Cover, Outer Lower; Front Cover; Outer Timing Cover; Cover Timing Case
- Position: Lower Outer
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, Touring, Touring Plus | 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 5184495AO
$921.57 MSRP: $1405.00
You Save: $483.43 (35%)
ADD TO CART
Product Specifications
- Other Name: Cover - Chain Case; Engine Timing Cover; Front Cover
- Replaces: 5184495AK, 5184495AL, 5184495AJ, 5184495AN, 5184495AM
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chrysler Town & Country | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: MD301136
$5.05 MSRP: $6.40
You Save: $1.35 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover V6 Assembly Timing Belt Front Up; Front Cover; Upper Timing Cover; Upper Cover
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS
View related parts
Chrysler Town & Country Timing Cover, Upper Outer Part Number: 4892136AC
$840.29 MSRP: $1075.00
You Save: $234.71 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover - Timing Case; Engine Timing Cover, Inner, Outer Upper; Front Cover; Inner Timing Cover; Cover Timing Case
- Position: Upper Outer
- Replaces: 4892136AA, 4892136AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, Touring, Touring Plus | 4.0L V6, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 4897571AD
$812.60 MSRP: $932.00
You Save: $119.40 (13%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover Package - Engine Timing; Front Cover
- Replaces: 4897571AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-2000 Chrysler Town & Country | Base, LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: MD144769
Product Specifications
- Other Name: Cover - Timing Belt; Lower Cover; Timing Belt Outer, Lower Up To 9/88; Cover Assembly, Timing Belt
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 5184495AH
$321.77 MSRP: $474.00
You Save: $152.23 (33%)
Product Specifications
- Other Name: Cover - Chain Case; Engine Timing Cover; Front Cover; Cover Chain Case
- Replaces: 5184495AG, 5184495AD, 5184495AF, 5184495AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chrysler Town & Country | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 4343821
Product Specifications
- Other Name: Cover Timing Belt Lower; Lower Timing Cover; Cover, Timing Belt Cover Lower
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1986-1988 Chrysler Town & Country | Base, Mark Cross | 4 Cyl 2.5 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 4343807
Product Specifications
- Other Name: Cover; Lower Timing Cover; Cover, Timing Belt Lower (Except Edr Turbo - Intercooler); Cover, Timing Belt, Lower
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984 Chrysler Town & Country | Base | 4 Cyl 2.2 L GAS
View related parts
Chrysler Town & Country Lower Cover Part Number: MD301133
Product Specifications
- Other Name: Gasket - Timing Belt Cover; Timing Cover Gasket; Timing Cover Seal; Timing Cover; Lower Cover Seal
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS
View related parts
Chrysler Town & Country Timing Cover, Upper Outer Part Number: 4892270AA
Product Specifications
- Other Name: Cover - Timing Case; Engine Timing Cover, Outer Upper; Front Cover; Outer Timing Cover; Cover Timing Case
- Position: Upper Outer
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | Limited, Touring, Touring Plus | 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 5019333AF
Product Specifications
- Other Name: Cover Package - Engine Timing; Engine Timing Cover; Front Cover
- Replaces: 5019333AB, 5019333AC, 5019333AE, 5019333AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 5137544AE
Product Specifications
- Other Name: Cover Package - Engine Timing; Engine Timing Cover; Front Cover
- Replaces: 5137544AC, 5137544AB, 5137544AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Chrysler Town & Country | Base, LX, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Timing Cover Part Number: 68262818AA
Product Specifications
- Other Name: Cover Package - Timing; Engine Timing Cover; Front Cover
- Replaces: 68029219AB, 68029219AC, 68029219AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | LX, Touring, Touring Plus, Walter P. Chrysler Signature Series | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS

Chrysler Town & Country Timing Cover

Choose OEM Timing Cover that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Timing Cover follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Timing Cover of Chrysler Town & Country vehicles play an essential in protecting the vehicle's timing mechanism which can be done through the use of a Chrysler Town & Country timing belt, Chrysler Town & Country timing chain, or Chrysler Town & Cam belt. Made of a rigid material including aluminum, plastic as well as steel, the Timing Cover shields the internal parts from being wrecked by debris. Some of the Chrysler Town & Country Timing Covers include gaskets that add to the safeguarding of the timing belt. Different types of Timing Covers have been used over the years in Town & Country models with each new model having the same basic job of protection as the last. However these covers can wear out quickly and a breakdown in these components is possible without the proper servicing, the replacement is crucial for safe usage of the vehicles. It was identified that the Timing Cover plays an important role of the Chrysler Town & Country and hence it should be serviced adequately to ensure it serve its required course effectively.

Chrysler Town & Country Timing Cover Parts and Q&A

Timing Cover, Upper Outer
4892270AA
Q: How to Install the Front Timing Cover and Its Components on Chrysler Town & Country?
A:
When installing the belt cover, wash and dry both the engine block holes and all the timing bolts to ensure there is no oil and be sure to add thread sealant to the bolts that connect to the oil pump. Start with the front timing belt cover and afterwards set up the upper Engine Mount. After that, attach the fuel supply line to the Fuel Rail and place the air cleaner housing. Remove the floor jack and raise the vehicle, then screw in the power steering pump, tightening them up to 23 Nm (200 lbs. in.). Next, fit the crankshaft damper, ensure the accessory drive Belt Tensioner is in place and then tighten the fastener to 28 Nm (250 in. lbs.). Connect the accessory Drive Belt, drive your vehicle down onto the ground and then complete by connecting the negative battery cable.
Timing Cover, Upper Outer
4892136AC
Q: How to remove a timing cover on Chrysler Town & Country?
A:
Before removing the engine timing cover, isolate the negative battery cable and drain out the cooling system. Lift the car on a motor hoist and then remove all the oil from its engine. Take out the right front tire and wheel assembly and then remove the inner splash shield located there. Following that, remove the Oil Pan and the oil pick-up tube. Remove the accessory Drive Belt and then remove one bolt and three nuts to adjust the A/C compressor. Disconnect the vibration damper for the crankshaft and take off the heater return hose from its place on the timing chain case or Water Pump inlet tube if your engine has an oil cooler. Take out the lower radiator hose and the Camshaft Position Sensor from the timing chain cover. Remove the Engine Mount on the right side and loosen the bolt from the power steering line support bracket. Take off two bolts, a nut and then another bracket, plus yet another bolt and nut. Rearrange the generator by taking out the generator's bolts, then take out three mounting bolts from below the pump pulley to move the Power Steering Pump. After removing the bolt and tensioner, remove both the bolt and the idler pulley on the accessory drive belt. With the water pump removed, get rid of the timing chain cover fasteners and then remove the timing chain cover.