How to measure Rod Bearing Clearances with Plastigage on Dodge Caliber?

Plastigage should be used to measure the bearing clearances, though first wipe away any oil on the bearing's surface, as Plastigage can dissolve in oil. After that, attach Plastigage over the width of the journal and, if there are areas of concern, place another strip of Plastigage on top. Screw on the bearing cap bolts per your manual's instructions, take off the bearing cap and align the reduced material from the Plastigage to the scale to measure the gap. Note all the measurements and realize that contrast between the readings from both ends indicates how much taper is there. Review the clearance measurements against what is suggested in engine specifications. Plastigage gives the measurements in both inches and millimeters. You should pick the right color of Plastigage to go with the specifications you're checking. Afterward, put in the required crankshaft bearings to get the correct bearing clearances.

How to Choose and Install Rod Bearings on Dodge Caliber?

Three distinct sizes of rod bearings can be used and each type is identified by a mark on the nose of the crankshaft. For the right bearing selection, check the proper table. Use Plastigage to check for connecting rod bearing clearance and use Engine Specifications for the acceptable values. You should never reuse rod bolts. When you put in new rod bolts, ensure you oil both the threads and the space under where the bolt head will sit with clean engine oil. Put in every bolt by hand so they're finger tight, then twist each bolt clockwise in rotation until each one's torque is correct. Tighten the bolts to 27 Nm (about 20 ft. lbs.) first and then add an extra 90°. After that, insert a feeler gauge into the connecting rod side and look up its recommended clearances in the builds specifications.

OEM Dodge Caliber Rod Bearing

Engine Connecting Rod Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Rod Bearings found

View related parts
Dodge Caliber Bearings Part Number: 4884912AB
$16.02 MSRP: $23.55
You Save: $7.53 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing - Connecting Rod; Rod Bearing; Bearing Connecting Rod Standard See Note
- Replaces: 1115A150, 4884912AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2012 Dodge Caliber | Express, Heat, Mainstreet, R/T, Rush, SE, SXT, SXT Plus, Uptown | 1.8L L4, 2.0L L4, 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Bearings Part Number: 4884807AC
Product Specifications
- Other Name: Bearing - Connecting Rod; Rod Bearing; Bearing Connecting Rod See Note
- Replaces: 5047024AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Caliber | SRT-4 | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Bearings, Black Part Number: 4884806AC
Product Specifications
- Other Name: Bearing - Connecting Rod; Rod Bearing; Bearing Connecting Rod See Note
- Replaces: 5047023AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Caliber | SRT-4 | 2.4L L4, 4 Cyl 2.4 L GAS
View related parts
Dodge Caliber Bearings, Green Part Number: 4884808AC
Product Specifications
- Other Name: Bearing - Connecting Rod; Rod Bearing; Bearing Connecting Rod See Note
- Replaces: 5047025AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Caliber | SRT-4 | 2.4L L4, 4 Cyl 2.4 L GAS

Dodge Caliber Rod Bearing

Choose OEM Rod Bearing that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Rod Bearing follows strict manufacturing steps to lock in quality and fit. If your Dodge Caliber matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Caliber parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

It is a very important part that has a great impact in the performance and durability of Dodge Caliber vehicles and it is known as Dodge Caliber Rod Bearing. Also known as the main journal bearing, the Rod Bearing is intended to accommodate and support such essential engine shafts as the crankshaft and the camshaft; the bearing allows shafts to rotate freely while an oil film supplied under pressure by the engine oil pump preserves the space between the shafts and the bearing wall. The types that are available are the bi-metal and tri-metal construction and the Dodge Caliber Rod Bearing is one that has to be accurated machined to fit into the bearing 'saddle' of the cylinder block in correct orientation and with correct alignment of the oil hole on the bearing to that of the block passage. This precision enhances the function of the Dodge Caliber and has a critical function in the improvement of safety by eliminating possible problems that could happen with the engine. Solving the issues of friction, strength and high temperature the tri-metal Rod Bearing, which can be coated with a special dry film can be considered a distinctive element of the automotive market. Compatibility with the Dodge Caliber SE and SXT model guarantees the driver the opportunities of comprehending this excellent Rod Bearing on various vehicles. That is why using the Dodge Caliber Rod Bearing as one of the key components is a savvy purchase because this car part reinforces the reliability and performance of the Dodge Caliber vehicles needed to make a customer's driving experience perfect.

Dodge Caliber Rod Bearing Parts and Q&A

Bearings, Black
4884806AC
Q: How to measure Rod Bearing Clearances with Plastigage on Dodge Caliber?
A:
Plastigage should be used to measure the bearing clearances, though first wipe away any oil on the bearing's surface, as Plastigage can dissolve in oil. After that, attach Plastigage over the width of the journal and, if there are areas of concern, place another strip of Plastigage on top. Screw on the bearing cap bolts per your manual's instructions, take off the bearing cap and align the reduced material from the Plastigage to the scale to measure the gap. Note all the measurements and realize that contrast between the readings from both ends indicates how much taper is there. Review the clearance measurements against what is suggested in engine specifications. Plastigage gives the measurements in both inches and millimeters. You should pick the right color of Plastigage to go with the specifications you're checking. Afterward, put in the required Crankshaft bearings to get the correct bearing clearances.
Bearings
4884912AB
Q: How to Choose and Install Rod Bearings on Dodge Caliber?
A:
Three distinct sizes of rod bearings can be used and each type is identified by a mark on the nose of the Crankshaft. For the right bearing selection, check the proper table. Use Plastigage to check for connecting rod bearing clearance and use Engine Specifications for the acceptable values. You should never reuse rod bolts. When you put in new rod bolts, ensure you oil both the threads and the space under where the bolt head will sit with clean engine oil. Put in every bolt by hand so they're finger tight, then twist each bolt clockwise in rotation until each one's torque is correct. Tighten the bolts to 27 Nm (about 20 ft. lbs.) first and then add an extra 90°. After that, insert a feeler gauge into the connecting rod side and look up its recommended clearances in the builds specifications.