How to Install Exhaust Valve and Intake Valves on Dodge Durango?

Before installing the intake and exhaust valves, cover their stems with engine oil and insert them into the cylinder head. Now, put in the valve stem seal (3) and check that it's firmly installed and the garter spring at the top remains whole. Afterward, set the spring into place and slide on the spring retainer (2). With the valve spring compressor, squeeze the spring as you set in the two halves of the valve spring retainer. Following the release of the valve spring compressor, make certain the two halves of the spring retainer (1) and the spring retainer (2) are properly seated. First, lube the camshaft journals with fresh, clean engine oil, place them with the sprocket dowels pointing to 11 o'clock on the left camshaft and 12 o'clock on the right and then set the bearing caps onto the camshafts. Loosely insert and tighten each camshaft bearing cap retaining hole bolt in the order shown until torque is reached. Lastly, place the hydraulic lash adjusters and rocker arms.

How Do Exhaust Valves and Intake Valves Get Removed and Replaced on Dodge Durango?

The first thing to do is take off the cylinder heads to get to the valve. Take off the cylinder head covers before you remove the rocker arms and the lash adjusters. After that, remove the camshaft bearing caps and the camshaft. Although all the steps are the same for every valve and its spring, this guide will focus on one particular valve and spring. Move Tool C-3422-B or C-3422-C Valve Spring Compressor and Tool 8519 Adapter into place to press the valve spring down and if needed, tap the top of the valve spring with a screwdriver to get the retainer locks to release. Properly remove the two halves of the spring retainer lock so that the valve spring does not come loose while you're no longer compressing it. Once you remove the valve spring compressor, remove the spring retainer and spring, look for sharp edges in the keeper grooves and get rid of any burrs on the valve stem before removing the valve from the cylinder head. Because intake and exhaust valve stem seals are the same, disconnect one and mark the valve for installation. It's good practice to test and check the valve springs before they are installed again during a rebuild. Inspect the valve springs for wear and set the reference surface on Tool C-647 against the mark of 40.12 mm, then pull on the torque wrench firmly until a ping occurs; the spring load is found by doubling the reading you get from the wrench. Use only springs that meet the requirements.

OEM Dodge Durango Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Intake Valves found

View related parts
Dodge Durango Intake Valve Part Number: 5038331AB
$93.10 MSRP: $141.00
You Save: $47.90 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard Quantity Is Per Cylinder Head; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2025 Dodge Durango | SRT, SRT 392, SRT 392 Plus, SRT 392 Premium, SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium | 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango Intake Valve Part Number: 5047917AA
$13.62 MSRP: $20.30
You Save: $6.68 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2016-2025 Dodge Durango | Citadel, GT, GT Plus, GT Premium, Limited, Pursuit, SXT, SXT Plus, Special Service | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Durango Intake Valve Part Number: 5184127AC
$24.74 MSRP: $36.70
You Save: $11.96 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel, Crew, Express, Heat, Limited, Rallye, SXT, Special Service | 6 Cyl 3.6 L FLEX
View related parts
Dodge Durango Intake Valve Part Number: 53022087AC
$25.03 MSRP: $37.15
You Save: $12.12 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard
- Replaces: 53022087AA, 53022087AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2025 Dodge Durango | 5.7L V8
- 2009 Dodge Durango | 5.7L V8
View related parts
Dodge Durango Intake Valve Part Number: 53020747AB
$46.65 MSRP: $94.55
You Save: $47.90 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valves; Valve Intake Standard 3 Per Cylinder Head; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2009 Dodge Durango | Adventurer, Base, Limited, SE, SLT, SLT Plus, ST, SXT, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Durango Intake Valve Part Number: 53006723
$19.33 MSRP: $24.50
You Save: $5.17 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard; Valve, Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2003 Dodge Durango | Base, R/T, SLT, SLT Plus, SXT, Sport | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Durango Intake Valve Part Number: 53021550AA
Product Specifications
- Other Name: Valve - Intake; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Dodge Durango | Adventurer, Limited, SLT, ST, SXT | 8 Cyl 5.7 L GAS
View related parts
Dodge Durango Intake Valve Part Number: 53021990AA
Product Specifications
- Other Name: Valve - Intake; Valves; Valve Intake Standard
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2009 Dodge Durango | Adventurer, Limited, SE, SLT, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS

Dodge Durango Intake Valve

Choose OEM Intake Valve that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Intake Valve follows strict manufacturing steps to lock in quality and fit. If your Dodge Durango matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Durango parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Durango Intake Valve is an essential part with a dramatic effect on the performance and durability of Dodge Durango cars. A popular component in maintaining the air and fuel combustion ratio in vehicles, the Intake Valve plays a big part in achieving the correct combustion rate important in sustaining the power characteristic of a vehicle's engine. Intake Valve is a crucial component of the car's engine; thus, any failure could be disastrous, which makes its efficiency important for the Dodge Durango consumers. Intended for Durango of different generations, the Intake Valve is suitable for creating the necessary conditions for the operation of all models. Dodge Durango Intake Valve not only improves the ability of the car's engine to operate efficiently but also adds to the safety of the car as well as preventing issues with combustions that would lead to the failure of the engine. Special aspects of designing Intake Valve are focused on its strength to endure relatively high temperature and pressure while having its fine and perfect structure to fit and work its way. This is due to the fact that, in the automotive market, detail is paramount which is why, anyone looking to improve their vehicle, will prefer Dodge Durango Intake Valve. Thus, the Intake Valve has been a central aspect of the Dodge Durango transformation over the years, and this means that each new generation of the car offers the power and durability that is characteristic of Dodge vehicles. Therefore, whenever one is seeking to enhance the performance as well as safety of the Dodge Durango then Dodge Durango Intake Valve is a must-have component in the market making it one of the best valued components for the modern automobiles.

Dodge Durango Intake Valve Parts and Q&A

Intake Valve
53020747AB
Q: How to Install Exhaust Valve and Intake Valves on Dodge Durango?
A:
Before installing the intake and exhaust valves, cover their stems with engine oil and insert them into the cylinder head. Now, put in the Valve Stem Seal (3) and check that it's firmly installed and the garter spring at the top remains whole. Afterward, set the spring into place and slide on the spring retainer (2). With the valve spring compressor, squeeze the spring as you set in the two halves of the valve spring retainer. Following the release of the valve spring compressor, make certain the two halves of the spring retainer (1) and the spring retainer (2) are properly seated. First, lube the Camshaft journals with fresh, clean engine oil, place them with the sprocket dowels pointing to 11 o'clock on the left camshaft and 12 o'clock on the right and then set the bearing caps onto the camshafts. Loosely insert and tighten each camshaft bearing cap retaining hole bolt in the order shown until torque is reached. Lastly, place the hydraulic Lash Adjusters and Rocker Arms.
Intake Valve
53021990AA
Q: How Do Exhaust Valves and Intake Valves Get Removed and Replaced on Dodge Durango?
A:
The first thing to do is take off the cylinder heads to get to the valve. Take off the cylinder head covers before you remove the Rocker Arms and the Lash Adjusters. After that, remove the Camshaft bearing caps and the camshaft. Although all the steps are the same for every valve and its spring, this guide will focus on one particular valve and spring. Move Tool C-3422-B or C-3422-C Valve Spring Compressor and Tool 8519 Adapter into place to press the valve spring down and if needed, tap the top of the valve spring with a screwdriver to get the retainer locks to release. Properly remove the two halves of the spring retainer lock so that the valve spring does not come loose while you're no longer compressing it. Once you remove the valve spring compressor, remove the spring retainer and spring, look for sharp edges in the keeper grooves and get rid of any burrs on the valve stem before removing the valve from the cylinder head. Because intake and exhaust Valve Stem Seals are the same, disconnect one and mark the valve for installation. It's good practice to test and check the valve springs before they are installed again during a rebuild. Inspect the valve springs for wear and set the reference surface on Tool C-647 against the mark of 40.12 mm, then pull on the torque wrench firmly until a ping occurs; the spring load is found by doubling the reading you get from the wrench. Use only springs that meet the requirements.