How to Maintain the Headlight Switch on Jeep Cherokee?

Always start by disconnecting the battery negative cable and allowing the ceramic dimmer resistor to cool for five minutes when the headlamp switch was on, as it might burn you. Remove the knee blocker from its place on the instrument console at the start. To remove it, extend the headlamp's switch control knob out to the ON position, reach through the open space around the steering column and press the inboard button on the switch body. Hold the release button while pulling the headlamp switch control knob and shaft away from you. Reach under the steering column and pull the switch into the opening to access the wire harness connectors and then use a wrench to loosen the nut on the opposite side and pull each of the connectors off the switch. Get rid of the headlamp switch from the instrument area. Place the headlamp switch within the opening of the steering column in the instrument panel and reattach both wire harness connectors. Put the headlamp switch into its mounting hole and then put the spanner nut on, tightening it to 2.7 Nm (24 in. lbs.). Feed the shaft of the knob and the shaft unit through the nut, into the headlamp switch and push them in completely. Attach the knee blocker to the right spot on the instrument panel and link the negative battery cable back to its hookup point.

How to Service the Headlight Switch on Jeep Cherokee?

Before starting the service, you must deactivate the air bag system by taking out the battery's negative cable, then wait for two minutes so the air bag capacitor is discharged and cannot deploy accidentally. Begin with taking out the knee blocker from the instrument panel. Push the headlamp switch down to ON, enter the steering column opening from the outboard side and press the release button found on the headlamp switch body inside the opening. As you continue to hold the release button down, pull out the headlamp switch control knob and shaft at the same time. After that, disconnect the two wire harness connectors on the panel from the headlamp switch receptacle and remove the headlamp switch from the panel. To install, place the headlamp switch where it belongs at the opening between the instrument panel and the steering column-then reinstall the wire harness connectors. Tuck the switch into the hole where it will be mounted and then put on the spanner nut, fastening it at 2.7 Nm (24 in.lbs.). Place the shaft of the knob and the shaft unit through the spanner nut to reach into the headlamp switch and push it all the way down. To complete, install the knee blocker on the device's panel and wire the negative cable from the battery back to the engine compartment.

OEM Jeep Cherokee Headlight Switch

Headlamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Headlight Switches found

View related parts
Jeep Cherokee Headlamp Switch Part Number: 56021898AB
$79.83 MSRP: $122.00
You Save: $42.17 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1996 Jeep Cherokee | Base, Briarwood, Classic, Country, Laredo, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 68155995AC
$100.23 MSRP: $152.00
You Save: $51.77 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp; Switch Headlamp
- Replaces: 68155995AA, 68155995AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2018 Jeep Cherokee | 75th Anniversary, Latitude, Latitude Plus, Limited, Overland, Sport, Trailhawk | 2.4L L4, 3.2L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 56009869AC
$60.32 MSRP: $90.45
You Save: $30.13 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp
- Replaces: 56009869AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2001 Jeep Cherokee | Classic, Country, Limited, SE, Sport | 2.5L L4, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 68154356AE
$84.29 MSRP: $126.00
You Save: $41.71 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp; Headlight Switch
- Replaces: 68154356AA, 68154356AB, 68154356AC, 68154356AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Jeep Cherokee | 75th Anniversary, 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Sport, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 68154353AE
$119.31 MSRP: $181.00
You Save: $61.69 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp; Headlight Switch; Switch Headlamp
- Replaces: 68154353AC, 68154353AD, 68154353AA, 68154353AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Jeep Cherokee | 75th Anniversary, 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Sport, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 68159551AC
$156.10 MSRP: $236.00
You Save: $79.90 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp; Headlight Switch; Switch Headlamp
- Replaces: 68159551AB, 68159551AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2018 Jeep Cherokee | 75th Anniversary, Latitude, Latitude Plus, Limited, Overland, Sport, Trailhawk | 2.4L L4, 3.2L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 68156006AC
$64.07 MSRP: $94.35
You Save: $30.28 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp Leveling; Switch Headlamp Leveling
- Replaces: 68156006AB, 68156006AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2018 Jeep Cherokee | 75th Anniversary, Latitude, Latitude Plus, Limited, Overland, Sport, Trailhawk | 2.4L L4, 3.2L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 68156030AC
$50.91 MSRP: $75.70
You Save: $24.79 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp Leveling; Switch Headlamp Leveling Headlamp Switch With Automatic Leveling Headlamps
- Replaces: 68156030AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2019-2023 Jeep Cherokee | 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Cherokee Headlamp Switch Part Number: 56001197
$30.90 MSRP: $39.17
You Save: $8.27 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Headlamp; Switch, Headlamp
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1991 Jeep Cherokee | Base, Briarwood, Chief, Laredo, Limited, Pioneer, Sport | 4 Cyl 2.1 L DIESEL, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Turn Signal Switch Part Number: 56010315AA
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Multifunction Left Stalk for Interior/Exterior Lights & Turn Signal Controls.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2001 Jeep Cherokee | Classic, Country, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Cherokee Ignition Switch Part Number: 4728424
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Windshield Washer Switch.; Turn Signal Switch; Multifunction, Wiper, Headlamp Dimmer, Hazard, Signal & Tilt options.
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1996 Jeep Cherokee | Classic, Country, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS

Jeep Cherokee Headlight Switch

Choose OEM Headlight Switch that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Headlight Switch follows strict manufacturing steps to lock in quality and fit. If your Jeep Cherokee matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Cherokee parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Headlight Switch used in Jeep Cherokee class of vehicles plays an important role of toggling on or off the headlights for enhanced safety of the vehicle. This switch provides the changing of the stock headlight from on to off position in addition to regulating the luminance variations of the light beams thus enabling better sighting during different roads and road conditions. There have been changes in the style of Headlight Switches used in Jeep Cherokee and this is in relation to design and technology of switches in use. Even though this objective is the same, there may be fluctuations in the processes and options available, including settings for low beams or programmed headlights. These changes meet the changing needs of drivers and their preferences, thus helping Jeep Cherokee meet the lighting needs of its consumers.

Jeep Cherokee Headlight Switch Parts and Q&A

Headlamp Switch
56009869AC
Q: How to Maintain the Headlight Switch on Jeep Cherokee?
A:
Always start by disconnecting the battery negative cable and allowing the ceramic dimmer resistor to cool for five minutes when the headlamp switch was on, as it might burn you. Remove the knee blocker from its place on the instrument console at the start. To remove it, extend the headlamp's switch control knob out to the ON position, reach through the open space around the steering column and press the inboard button on the switch body. Hold the release button while pulling the headlamp switch control knob and shaft away from you. Reach under the steering column and pull the switch into the opening to access the wire harness connectors and then use a wrench to loosen the nut on the opposite side and pull each of the connectors off the switch. Get rid of the headlamp switch from the instrument area. Place the headlamp switch within the opening of the steering column in the instrument panel and reattach both wire harness connectors. Put the headlamp switch into its mounting hole and then put the spanner nut on, tightening it to 2.7 Nm (24 in. lbs.). Feed the shaft of the knob and the shaft unit through the nut, into the headlamp switch and push them in completely. Attach the knee blocker to the right spot on the instrument panel and link the negative Battery Cable back to its hookup point.
Turn Signal Switch
56010315AA
Q: How to Service the Headlight Switch on Jeep Cherokee?
A:
Before starting the service, you must deactivate the air bag system by taking out the battery's negative cable, then wait for two minutes so the air bag capacitor is discharged and cannot deploy accidentally. Begin with taking out the knee blocker from the instrument panel. Push the headlamp switch down to ON, enter the steering column opening from the outboard side and press the release button found on the headlamp switch body inside the opening. As you continue to hold the release button down, pull out the headlamp switch control knob and shaft at the same time. After that, disconnect the two wire harness connectors on the panel from the headlamp switch receptacle and remove the headlamp switch from the panel. To install, place the headlamp switch where it belongs at the opening between the instrument panel and the steering column-then reinstall the wire harness connectors. Tuck the switch into the hole where it will be mounted and then put on the spanner nut, fastening it at 2.7 Nm (24 in.lbs.). Place the shaft of the knob and the shaft unit through the spanner nut to reach into the headlamp switch and push it all the way down. To complete, install the knee blocker on the device's panel and wire the negative cable from the battery back to the engine compartment.