How to Replace the Headlight Switch for Headlamp Leveling on Jeep Liberty?

On cars made for some specific markets that require headlamp leveling, first turn off the air bag system by disconnecting the battery negative cable, wait two minutes and then replace the leveling switch. Start by taking out the driver side inboard bezel on the instrument panel and after that, unplug the instrument panel wire harness connector from the headlamp leveling switch. Pull the lower latches on the switch toward you from behind the trim bezel, then rock the switch out from below. Squeeze the upper latch to totally remove the switch. Put the headlamp leveling switch housing against the hole for installation and push firmly until stuck and the latches engage. Bring the switch and bezel unit to the instrument panel, join the wire harness harness connector, return the driver side inboard bezel in place and complete by reconnecting the battery negative cable.

How to Install the Headlight Switch on the Left Multifunction Control on Jeep Liberty?

You should first turn off the Supplemental Restraint System (SRS) by disconnecting and isolating the negative battery cable for two minutes to keep the air bag system from being activated by accident. Situate the left multi-function switch close by the attached bracket which is located on the Clock Spring's left side and join the jumper wire harness to the connector inside the switch case on the previous side of the assembly. Position the switch housing's slide tabs over the channel formations on the Clock Spring bracket and slide the switch into the bracket so it fits securely. Fasten the tab on the offering side of the switch to the bracket using screw 2 and tighten to 1 Nm (10 in. lbs.). Tighten the steering column shroud wires onto the switch housing and install the lower and upper steering shrouds. Once the testing is finished, return the negative battery cable to its clamp.

OEM Jeep Liberty Headlight Switch

Headlamp Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Headlight Switches found

View related parts
Jeep Liberty Turn Signal Switch Part Number: 68015101AG
$89.70 MSRP: $135.00
You Save: $45.30 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Switch Multifunction
- Replaces: 68015101AE, 68015101AD, 68015101AC, 68015101AF, 68015101AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Turn Signal Switch Part Number: 68041491AD
$121.54 MSRP: $184.00
You Save: $62.46 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Combination Switch; Multi Purpose Switch; Multifunction Switch; Switch Multifunction
- Replaces: 68024197AB, 68041491AB, 68041491AC, 68041491AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Multifunction Switch Part Number: 68015102AF
$162.84 MSRP: $247.00
You Save: $84.16 (35%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Switch Housing.; Switch Multifunction
- Replaces: 68015102AC, 68015102AA, 68015102AB, 68015102AD, 68015102AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2012 Jeep Liberty | Jet, Limited, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Turn Signal Switch Part Number: 68041485AD
$112.62 MSRP: $172.00
You Save: $59.38 (35%)
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Signal Switch; Switch Multifunction
- Replaces: 5183947AC, 68041485AA, 68041485AB, 5183947AA, 68041485AC, 5183947AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2011 Jeep Liberty | Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Turn Signal Switch Part Number: 5183952AF
$44.94 MSRP: $66.60
You Save: $21.66 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Multi Purpose Switch; Multifunction Switch; Headlamp Switch; Switch Multifunction
- Replaces: 5183952AA, 5183952AC, 5183952AB, 5183952AD, 5183952AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2011 Jeep Liberty | Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Turn Signal Switch Part Number: 5183950AF
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183950AE, 5183950AD, 5183950AC, 5183950AB, 5183950AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Jeep Liberty | Limited, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Turn Signal Switch Part Number: 5183946AF
Product Specifications
- Other Name: Switch - Multifunction; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183946AA, 5183946AD, 5183946AE, 5183946AB, 5183946AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Headlamp Switch Part Number: 56010204AE
Product Specifications
- Other Name: Switch - Headlamp Leveling; Switch Headlamp Leveling
- Replaces: 56010204AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport | 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS

Jeep Liberty Headlight Switch

Choose OEM Headlight Switch that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Headlight Switch follows strict manufacturing steps to lock in quality and fit. If your Jeep Liberty matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Liberty parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Jeep Liberty Headlight Switch Parts and Q&A

Headlamp Switch
56010204AE
Q: How to Replace the Headlight Switch for Headlamp Leveling on Jeep Liberty?
A:
On cars made for some specific markets that require headlamp leveling, first turn off the air bag system by disconnecting the battery negative cable, wait two minutes and then replace the leveling switch. Start by taking out the driver side inboard bezel on the instrument panel and after that, unplug the instrument panel wire harness connector from the headlamp leveling switch. Pull the lower latches on the switch toward you from behind the trim bezel, then rock the switch out from below. Squeeze the upper latch to totally remove the switch. Put the headlamp leveling switch housing against the hole for installation and push firmly until stuck and the latches engage. Bring the switch and bezel unit to the instrument panel, join the wire harness harness connector, return the driver side inboard bezel in place and complete by reconnecting the battery negative cable.
Turn Signal Switch
68041485AD
Q: How to Install the Headlight Switch on the Left Multifunction Control on Jeep Liberty?
A:
You should first turn off the Supplemental Restraint System (SRS) by disconnecting and isolating the negative Battery Cable for two minutes to keep the air bag system from being activated by accident. Situate the left multi-function switch close by the attached bracket which is located on the Clock Spring's left side and join the jumper wire harness to the connector inside the switch case on the previous side of the assembly. Position the switch housing's slide tabs over the channel formations on the Clock Spring bracket and slide the switch into the bracket so it fits securely. Fasten the tab on the offering side of the switch to the bracket using screw 2 and tighten to 1 Nm (10 in. lbs.). Tighten the steering column shroud wires onto the switch housing and install the lower and upper steering shrouds. Once the testing is finished, return the negative battery cable to its clamp.