OEM 2004 Dodge Durango Brake Light Switch

Brake Lamp Switch
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Brake Light Switches found

  • 2004 Dodge Durango Brake Light Switch Diagram - 4221463
    View related parts

    2004 Dodge Durango Parking Brake Switch, Black Part Number: 4221463

    $18.50 MSRP: $27.20
    You Save: $8.70 (32%)
    Ships in 1-2 Business Days
    ADD TO CART
    Product Specifications
    • Other Name: Switch - Parking Brake; Electronic Parking Brake Control Switch; Parking Brake Warning Switch; Seat Adjuster, W/Bezel, Black Buttons, Woodgrain, W/Memory Opening.
    • Item Weight: 0.40 Pounds
    • Item Dimensions: 1.5 x 1.6 x 2.6 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 4221463
    • Warranty: This genuine part is guaranteed by Mopar's factory warranty.
    More Info
    Fits the following 2004 Dodge Durango Submodels:
    • Adventurer, Base, Citadel, Crew, Express, GT, GT Plus, GT Premium, Heat, Limited, Limited Hybrid, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, Rallye, SE, SLT, SLT Plus, SRT, SRT 392, SRT 392 Plus, SRT 392 Premium, SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium, ST, SXT, SXT Plus, Special Service, Sport | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
  • 2004 Dodge Durango Brake Light Switch - 5083344AB
    2004 Dodge Durango Brake Light Switch Diagram - 5083344AB
    View related parts
    Product Specifications
    • Other Name: SW PKG-STOP LAMP
    • SKU: 5083344AB
    • Warranty: This genuine part is guaranteed by Mopar's factory warranty.
    Fits the following 2004 Dodge Durango Submodels:
    • Adventurer, Base, Limited, Limited Hybrid, R/T, SE, SLT, SLT Plus, ST, SXT, Sport | 3.7L V6, 4.7L V8, 5.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS

2004 Dodge Durango Brake Light Switch Parts and Q&A

  • Q: How to Service a Brake Light Switch on 2004 Dodge Durango?
    A: To service the brake light switch, first disconnect the black cable on the battery and wait two minutes before you open anything near the air bag system to ensure it does not deploy by mistake. This switch is designed for only one use, so if you take it out, you have to replace it. The brake lamp switch is next to the support bracket found on the lower steering column. Take the wire harness connector away, then rotate the switch housing part about a third of a full turn to the right until the switch's tabs line up with the key hole in the mounting bracket. Push the switch straight toward you and then take it out and throw it away. To install, brace the brake pedal, set the tabs on the collar into the keyed hole and seat the switch housing against the bracket as you gently push the tabs in. Counterclockwise twist the switch housing about 30 degrees to insert the tabs. Never pull the brake pedal before you're done with the switch plunger adjustment. Pull the brake pedal out without raising it and rotate the plunger lever to the left until it clicks in place and is parallel to the brake light switch. The switch plunger length is set when adjusting and this step cannot be reversed; if you don't do it right, you'll need to replace the switch. After that, connect the wire harness connector back to the brake lamp switch and reattach the negative battery cable.

Related 2004 Dodge Durango Parts