How to Remove and Replace a Control Arm on 2007 Chrysler Pacifica?

You should start by lining up the lower control arm inside the two attachment brackets of the engine cradle. Make sure you install the lower control arm bushings on the engine cradle using bolts placed from the rear and then place the nuts on the bolts, but do not tighten them. Set the steering knuckle, brake rotor and caliper in place and afterwards put in the tire and wheel assembly, turning the wheel mounting nuts 135 Nm (100 ft. lbs.). Raise the vehicle so it sits on an alignment rack or hoist. When the bolts are out of reach, raise the hoist until you can access them. At curb height, connect the lower control arm to the vehicle by tightening each mounting bolt to 163Nm (120ft. lbs).

OEM 2007 Chrysler Pacifica Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Control Arms found

View related parts
2007 Chrysler Pacifica Lower Control Arm, Front Driver Side Part Number: 4743477AI
Product Specifications
- Other Name: Arm - Control; Front Left Suspension Control Arm and Ball Joint Assembly.; Arm Control; Control Arm
- Position: Front Driver Side
- Replaces: 4743477AH, 4743477AF, 4743477AG, 4743477AE
- Item Weight: 16.30 Pounds
- Item Dimensions: 20.1 x 14.9 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4743477AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Pacifica Submodels:
- Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
2007 Chrysler Pacifica Lower Control Arm, Front Passenger Side Part Number: 4743476AI
Product Specifications
- Other Name: Arm - Control; Front Right Suspension Control Arm and Ball Joint Assembly.; Arm Control; Control Arm
- Position: Front Passenger Side
- Replaces: 4743476AG, 4743476AF, 4743476AH, 4743476AE
- Item Weight: 16.30 Pounds
- Item Dimensions: 19.7 x 14.5 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4743476AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Chrysler Pacifica Submodels:
- Base, LX, Limited, Touring | 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS

2007 Chrysler Pacifica Control Arm Parts and Q&A

Q: How to Remove and Replace a Control Arm on 2007 Chrysler Pacifica?
A: You should start by lining up the lower control arm inside the two attachment brackets of the engine cradle. Make sure you install the lower control arm bushings on the engine cradle using bolts placed from the rear and then place the nuts on the bolts, but do not tighten them. Set the steering knuckle, brake rotor and caliper in place and afterwards put in the tire and wheel assembly, turning the wheel mounting nuts 135 Nm (100 ft. lbs.). Raise the vehicle so it sits on an alignment rack or hoist. When the bolts are out of reach, raise the hoist until you can access them. At curb height, connect the lower control arm to the vehicle by tightening each mounting bolt to 163Nm (120ft. lbs).