OEM 2009 Dodge Durango Blend Door Actuator

Air Blend Door Actuator
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Blend Door Actuators found

  • 2009 Dodge Durango Blend Door Actuator Diagram - 68018109AA
    View related parts

    2009 Dodge Durango Actuator, Front Part Number: 68018109AA

    $131.43 MSRP: $195.00
    You Save: $63.57 (33%)
    ADD TO CART
    Product Specifications
    • Other Name: Actuator - A/C And Heater; HVAC Inlet Door (Front, Rear), Defrost, Blend, Heater Blend; Actuator A/C And Heater Includes: Mounting Screws; Actuator A/C And Heater Includes: Screws; Actuator A/C And Heater
    • Position: Front
    • Item Weight: 0.60 Pounds
    • Item Dimensions: 2.0 x 3.1 x 3.7 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 68018109AA
    • Warranty: This genuine part is guaranteed by Mopar's factory warranty.
    More Info
    Fits the following 2009 Dodge Durango Submodels:
    • Limited, Limited Hybrid, SE, SLT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS
  • 2009 Dodge Durango Blend Door Actuator Diagram - 4885206AB
    View related parts

    2009 Dodge Durango Door Actuator Part Number: 4885206AB

    $137.09 MSRP: $202.00
    You Save: $64.91 (33%)
    Product Specifications
    • Other Name: Actuator - A/C And Heater; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator; Servo; A/C and Heater Actuator with Bracket, Lever, and Recirculation Door.
    • Item Weight: 0.70 Pounds
    • Item Dimensions: 1.9 x 3.6 x 4.2 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 4885206AB
    • Warranty: This genuine part is guaranteed by Mopar's factory warranty.
    More Info
    Fits the following 2009 Dodge Durango Submodels:
    • Adventurer, Base, Limited, Limited Hybrid, R/T, SE, SLT, SLT Plus, ST, SXT, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS

2009 Dodge Durango Blend Door Actuator Parts and Q&A

  • Q: How Does the Installation of a Blend Door Actuator Differ Between Single Zone and Dual Zone HVAC Systems on 2009 Dodge Durango?
    A: While a single zone heating-A/C setup has only one blend door actuator, the dual-zone configuration is equipped with two-one each for the driver and passenger sides. On the passenger side, situate the blend door actuator at the top of the HVAC housing and, if required, rotate it slightly to bring the splines on its output shaft into alignment with those on the blend-air door linkage. Attach the blend door actuator to the HVAC housing with three screws-tighten each one to 2 Nm (17 in. lbs.)-and mate the HVAC wire harness connector to the actuator. After positioning the instrument panel assembly and restoring the negative battery cable connection, open the Actuator Calibration function with a scan tool. For the dual zone on the driver side, place the blend door actuator at the lower edge of the HVAC housing and align the splines match accordingly. Affix the actuator and its cover to the HVAC housing with three screws tightened to 2 Nm (17 in. lbs.), then fasten the HVAC wire harness connector, verifying that it is secure. Reattach the negative battery cable and run the Actuator Calibration through a scan tool.

Related 2009 Dodge Durango Parts