How to Service and Install an Oxygen Sensor and Engine Cover on Chrysler Crossfire?

Before you service the upstream O2 sensor, cover its threaded part with anti-seize compound. Insert the O2 sensor followed by tightening it to 50 Nm (37 ft. lbs.). After that, plug the O2 sensor harness connector into its place. For installing the engine cover, place the retaining clips on the rubber mounts and push them down hard so they stay in place. Adding a little lubricant to the engine cover rubber mounts will help the process. In the end, attach the negative battery cable.

How to Properly Remove and Install an Engine's Oxygen Sensor on Chrysler 300?

There are two heated oxygen sensors, one in every exhaust manifold, that the engine makes use of. Always confirm the engine is cooled off completely prior to removal, as hot exhaust manifold, pipes and a catalytic converter might burn you. Disconnect the negative terminal from the battery and then lift the vehicle with support underneath. Be sure to unplug the heated oxygen sensor's electrical connector, not by pulling the wire. Camera and video specialist Peter Demetri suggests using a Snap-On YA8875 or a crow foot wrench to remove the oxygen sensor. A new O2 sensor requires you to clear the PCM RAM by removing the PCM C-1 connector or briefly dropping the car's negative battery terminal to prevent the NGC from learning incorrect O2 heater information. After removing the sensor, put a 18 mm X 1.5 + 6E tap into the manifold and rotate it to clean the threads. When using the original sensor, put a layer of Loctite 771-64 on the threads; brand new sensors come coated already and do not need extra product. Set the sensor to a torque of 28 Nm (20 ft. lbs.), link up the connector of the heated oxygen sensor, let the car drop to the ground and then place the negative batter cable back on.

OEM Chrysler Oxygen Sensor

Oxygen O2 Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

77 Oxygen Sensors found

View related parts
Chrysler Oxygen Sensor, Front Part Number: 5149171AB
$129.16 MSRP: $190.00
You Save: $60.84 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Front Right, Rear, Rear Left, Rear Right; Oxygen Sensors: Front, Rear, Upper, Lower, Passenger/Driver Side, Before/After Catalytic Converter.
- Position: Front
- Replaces: 5149171AA, 68066160AA
Fits the following Chrysler Models:
- 200 | 2011-2017 | C, LX, Limited, S, Touring | 2.4L L4, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.6 L FLEX
- 300 | 2012-2023 | Base, C, C Luxury, C Platinum, Limited, S, Touring, Touring L | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
- Pacifica | 2017-2025 | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Town & Country | 2011-2016 | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
- Voyager | 2020-2025 | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View More
View related parts
Chrysler Oxygen Sensor, Front Driver Side Part Number: 56029049AA
$97.32 MSRP: $144.00
You Save: $46.68 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Front Right, Rear, Rear Left, Rear Right; Rear Oxygen Sensor; Front Oxygen Sensor; Upper Oxygen Sensor; Lower Oxygen Sensor; Sensor Oxygen
- Position: Front Driver Side
Fits the following Chrysler Models:
- 300 | 2005-2011 | Base, C, C SRT8, LX, Limited, S, Signature Series, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
- Aspen | 2007-2009 | Limited | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
- PT Cruiser | 2005-2010 | Base, Classic, Couture Edition, Dream Cruiser, GT, LX, Limited, Street Cruiser, Touring | 4 Cyl 2.4 L GAS
- Pacifica | 2007-2008 | Base, LX, Limited, Touring | 6 Cyl 4.0 L GAS
- Sebring | 2004-2010 | Base, GTC, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
- Town & Country | 2008-2010 | Limited, Touring, Touring Plus | 6 Cyl 4.0 L GAS
View More
View related parts
Chrysler Oxygen Sensor, Front Part Number: 56029050AA
$77.38 MSRP: $114.00
You Save: $36.62 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Right, Rear, Rear Left, Rear Right; Rear Oxygen Sensor; Front Oxygen Sensor; Lower Oxygen Sensor; Sensor Oxygen
- Position: Front
Fits the following Chrysler Models:
- 300 | 2005-2010 | C, C SRT8, LX, Limited, S, Signature Series, Touring | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
- Aspen | 2008-2009 | Limited, Limited Hybrid | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FULL HYBRID EV-GAS (FHEV)
- PT Cruiser | 2005-2010 | Base, Classic, Couture Edition, Dream Cruiser, GT, LX, Limited, Street Cruiser, Touring | 4 Cyl 2.4 L GAS
- Pacifica | 2005-2008 | Base, LX | 6 Cyl 3.8 L GAS
- Sebring | 2004-2006 | Base, GTC, LX, LXi, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
- Town & Country | 2004-2010 | Base, EX, LX, Limited, Touring, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View More
View related parts
Chrysler Oxygen Sensor, Rear Part Number: 56029085AA
$85.52 MSRP: $127.00
You Save: $41.48 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Front Left, Rear; Front Oxygen Sensor; Sensor Oxygen
- Position: Rear
Fits the following Chrysler Models:
- Pacifica | 2005-2008 | Base, LX | 6 Cyl 3.8 L GAS
- Town & Country | 2006-2008 | Base, LX, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Oxygen Sensor Part Number: 4606421
$23.51 MSRP: $29.81
You Save: $6.30 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Sensor Oxygen
Fits the following Chrysler Models:
- Sebring | 1998-2000 | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Oxygen Sensor, Front Passenger Side Part Number: 68144248AD
$76.49 MSRP: $115.00
You Save: $38.51 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Left, Front Right, Rear, Rear Right; Oxygen Sensors: Front, Rear, Lower, Passenger Side Upstream/Downstream, Driver Side Downstream.
- Position: Front Passenger Side
- Replaces: 68144248AA
Fits the following Chrysler Models:
- 300 | 2012-2013 | SRT8, SRT8 Core | 6.4L V8, 8 Cyl 6.4 L GAS
View related parts
Chrysler Oxygen Sensor, Front Part Number: 4727446AD
$119.04 MSRP: $179.00
You Save: $59.96 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front
- Position: Front
Fits the following Chrysler Models:
- Pacifica | 2004-2005 | Base, Limited, Touring | 6 Cyl 3.5 L GAS
View related parts
Chrysler Oxygen Sensor, Front Part Number: 4606133AE
$115.44 MSRP: $146.35
You Save: $30.91 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front, Rear; Sensor Oxygen
- Position: Front
Fits the following Chrysler Models:
- 300M | 2000-2001 | Base | 6 Cyl 3.5 L GAS
- Concorde | 2000-2001 | LX, LXi | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS
- LHS | 2000-2001 | Base | 6 Cyl 3.5 L GAS
View More
View related parts
Chrysler Front Oxygen Sensor Part Number: 68146512AA
$111.49 MSRP: $166.00
You Save: $54.51 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor; Sensor Oxygen
Fits the following Chrysler Models:
- 300 | 2013 | C, C Luxury, S | 8 Cyl 5.7 L GAS
View related parts
Chrysler Oxygen Sensor, Front Part Number: 5033758AA
$113.06 MSRP: $143.33
You Save: $30.27 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Oxygen; Oxygen Sensor, Front; Sensor Oxygen
- Position: Front
Fits the following Chrysler Models:
- PT Cruiser | 2001-2002 | Base, Dream, Limited, Touring | 4 Cyl 2.4 L GAS
View related parts
Chrysler Oxygen Sensor, Rear Part Number: 4686935AB
$141.50 MSRP: $212.00
You Save: $70.50 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Rear Oxygen Sensor; Sensor Oxygen
- Position: Rear
Fits the following Chrysler Models:
- Town & Country | 2001-2003 | Base, EL, EX, LX, LXi, Limited | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2001-2003 | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Oxygen Sensor Part Number: 4605654
$51.23 MSRP: $64.95
You Save: $13.72 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Oxygen - Exhaust Gas; Sensor, Oxygen (Use Insulator 4604603, 3.3 Engine) Upstream; Sensor, Oxygen , (W/18" Pigtail) 3.5 Engine
Fits the following Chrysler Models:
- Concorde | 1993-1996 | Base, LX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Oxygen Sensor, Front Part Number: 4606555AB
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front; Sensor Oxygen
- Position: Front
Fits the following Chrysler Models:
- Sebring | 2001-2004 | Base, GTC, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L GAS
View related parts
Chrysler Oxygen Sensor Part Number: 4606620
Product Specifications
- Other Name: Sensor; Sensor Oxygen
Fits the following Chrysler Models:
- Sebring | 1998-2000 | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Oxygen Sensor Part Number: 4671052
Product Specifications
- Other Name: Sensor; Sensor, Oxygen (Rear 2.0 Engine); Sensor, Oxygen, P Series
Fits the following Chrysler Models:
- Sebring | 1995-1996 | LX | 4 Cyl 2.0 L GAS
View related parts
Chrysler Oxygen Sensor, Front Passenger Side Part Number: MN158757
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Front Right; Sensor Oxygen
- Position: Front Passenger Side
Fits the following Chrysler Models:
- Sebring | 2004-2005 | LXi, Limited | 6 Cyl 3.0 L GAS
View related parts
Chrysler Oxygen Sensor Part Number: 4606063
Product Specifications
- Other Name: Sensor - Oxygen; Sensor, Oxygen, P Series; Sensor Oxygen
Fits the following Chrysler Models:
- Sebring | 1995-1998 | LX, LXi | 6 Cyl 2.5 L GAS
View related parts
Chrysler Oxygen Sensor, Rear Part Number: 4606135AD
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Sensor Oxygen
- Position: Rear
Fits the following Chrysler Models:
- Sebring | 2001-2004 | Base, LX | 4 Cyl 2.4 L GAS
View related parts
Chrysler Oxygen Sensor Part Number: 5269711
Product Specifications
- Other Name: Sensor Oxygen; Sensor, Oxygen, P Series; Sensor, Oxygen
Fits the following Chrysler Models:
- Sebring | 1997-1999 | LX | 4 Cyl 2.0 L GAS
View related parts
Chrysler Oxygen Sensor, Rear Part Number: MR560365
Product Specifications
- Other Name: Sensor - Oxygen; Oxygen Sensor, Rear; Rear Oxygen Sensor; Sensor Oxygen
- Position: Rear
Fits the following Chrysler Models:
- Sebring | 2001-2005 | Base, LX | 4 Cyl 2.4 L GAS

| Page 1 of 4 |Next >

1-20 of 77 Results

Chrysler Oxygen Sensor

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler Oxygen Sensor for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler Oxygen Sensor monitors balance in exhaust to ensure engines are smooth, clean and fuel savvy. Since 1925, Chrysler has been developing its reputation with the help of solid cars, well-valued in terms of ride comfort and reasonable prices. Chrysler reduced engine vibration using Floating Power and as such cabins remained stable even when traveling on uneven roads. Chrysler then went extreme with the styling, Airflow, directing air flowing and providing greater space to passengers. Later Chrysler released the pioneer practical minivan which showed the importance of space and easy access more than flash. The brand continued to perfect interior design by replacing empty space with actual seat room and practical storage. Drivers receive their ride in a composed way, passengers receive some quiet and everybody receives value without drama. The hardware is also supported by simple purchasing procedures; hence, the owners do not spend time haggling but driving. Oxygen Sensor is placed higher in the exhaust, its tip of zirconium dioxide is covered with platinum which alternates between the rich and lean voltages to inform the control unit how much fuel to cut. Another Oxygen Sensor downstream that compares converter output will indicate any catalyst that ceases to clean pollutants. Large band Oxygen Sensor units broaden the range and allow the computer to refine mixtures in smaller steps to make it sharper on economy. An Oxygen Sensor tends to deviate when it is covered with oil or simply wears out and consumes a lot of fuel without a corresponding increase in emissions.

Chrysler Oxygen Sensor Parts and Q&A

Oxygen Sensor, Rear Driver Side
5099817AA
Q: How to Service and Install an Oxygen Sensor and Engine Cover on Chrysler Crossfire?
A:
Before you service the upstream O2 sensor, cover its threaded part with anti-seize compound. Insert the O2 sensor followed by tightening it to 50 Nm (37 ft. lbs.). After that, plug the O2 sensor harness connector into its place. For installing the engine cover, place the retaining clips on the rubber mounts and push them down hard so they stay in place. Adding a little lubricant to the engine cover rubber mounts will help the process. In the end, attach the negative battery cable.
Oxygen Sensor, Front Passenger Side
56028994AB
Q: How to Properly Remove and Install an Engine's Oxygen Sensor on Chrysler 300?
A:
There are two heated oxygen sensors, one in every exhaust manifold, that the engine makes use of. Always confirm the engine is cooled off completely prior to removal, as hot exhaust manifold, pipes and a catalytic converter might burn you. Disconnect the negative terminal from the battery and then lift the vehicle with support underneath. Be sure to unplug the heated oxygen sensor's electrical connector, not by pulling the wire. Camera and video specialist Peter Demetri suggests using a Snap-On YA8875 or a crow foot wrench to remove the oxygen sensor. A new O2 sensor requires you to clear the PCM RAM by removing the PCM C-1 connector or briefly dropping the car's negative battery terminal to prevent the NGC from learning incorrect O2 heater information. After removing the sensor, put a 18 mm X 1.5 + 6E tap into the manifold and rotate it to clean the threads. When using the original sensor, put a layer of Loctite 771-64 on the threads; brand new sensors come coated already and do not need extra product. Set the sensor to a torque of 28 Nm (20 ft. lbs.), link up the connector of the heated oxygen sensor, let the car drop to the ground and then place the negative batter cable back on.