How to Service the Air Bag Sensor for Front Impact on Chrysler Town & Country?

Unplug the negative battery cable and unhook the SRS first, as you shouldn't work on the system while the battery is connected. Never strike or allow the front impact sensor to fall, as it may be harmed or its calibration changed; a fallen sensor always needs to be replaced. Open the front impact sensors by climbing onto the engine compartment's top and going down below the inboard side of the front lamp unit's housing. Open the front collision system by removing the front end module wire from the left or right front impact sensor's connector receptacle. Take out the screw that holds the front impact sensor to the backing of the front end module carrier. Slide the front impact sensor backwards which will separate the pin inside from its hole in the front end module carrier and then remove the sensor from the front of the engine compartment. The front and third row side impact sensors can be placed in either set of side door panels.

How to Maintain Air Bag Sensors for Front and Side Impact on Chrysler Town & Country?

Start by opening your hood and disconnecting the negative battery cable; then wait two minutes before resuming any work to avoid accidental deployment. After hoisting the car, remove the front impact sensor by sticking a hook under it and pulling, then disconnect the electrical connector and unfasten the two screws attaching it to the outer rails. Once the side impact sensors are mounted to the B-pillar, open the hood, disconnect the negative cable and allow two minutes of discharge. On the same side as the sensor, take out the lower trim where the B-pillar is found, pull out the electrical connector from the impact sensor and remove all the screws at the bracket before you remove it. If using sliding door opening sensors that are mounted sideways, once again open the hood, unhook the negative battery cable and then let the capacitor discharge for two minutes. Pull open the sliding door, undo the impact sensor's holding screws, unhook the connection wiring and remove the sensor from the vehicle. With the quarter panel mounted side impact sensors, lift the hood, unhook the negative battery cable and let the capacitor discharge for two minutes before you touch anything else. Open the quarter trim door where the old sensor is, take out its two hold down screws, disconnect the electrical cable and remove the sensor.

OEM Chrysler Town & Country Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Air Bag Sensors found

View related parts
Chrysler Town & Country Impact Sensor, Front Part Number: 4671779AC
$48.02 MSRP: $103.00
You Save: $54.98 (54%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor, Center, Front; Air Bag Sensor; Front Impact Sensor; Side Impact Sensor; Airbag Impact Sensor.
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chrysler Town & Country | Base, LX, Limited, Touring | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Impact Sensor, Rear Part Number: 4606958AB
$74.87 MSRP: $112.00
You Save: $37.13 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor, Rear; Air Bag Sensor; Side Impact Sensor; Sensor Impact
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2012 Chrysler Town & Country | LX, Limited, Touring, Touring L, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Impact Sensor, Passenger Side Part Number: 4727069AD
$54.24 MSRP: $68.85
You Save: $14.61 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Airbag Impact; Air Bag Impact Sensor, Right; Air Bag Sensor; Side Impact Sensor; Sensor Side Airbag Impact
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Front Impact Sensor Part Number: 4896011AB
$151.82 MSRP: $224.00
You Save: $72.18 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Acceleration; Air Bag Impact Sensor, Front; Air Bag Sensor; Sensor Impact
- Position: Front
- Replaces: 56054046AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Town & Country | LX, Limited, Touring, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Town & Country Front Impact Sensor Part Number: 5170520AB
$42.08 MSRP: $53.34
You Save: $11.26 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor, Front; Air Bag Sensor
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chrysler Town & Country | Base, LX, Limited, Touring | 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Impact Sensor, Driver Side Part Number: 4727261AD
$45.89 MSRP: $58.35
You Save: $12.46 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Airbag Impact; Air Bag Impact Sensor, Left; Air Bag Sensor; Side Impact Sensor; Sensor Side Airbag Impact
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2007 Chrysler Town & Country | Base, EL, EX, LX, LXi, Limited, Touring | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Impact Sensor, Front Part Number: 4896059AA
Product Specifications
- Other Name: Sensor - Air Bag; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Impact Sensor; Front Sensor; Side Impact Sensor; Side Sensor; Sensor; Sensor Air Bag
- Position: Front
- Replaces: 4896023AA, 4686957AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2007 Chrysler Town & Country | Base, EX, LX, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Town & Country Knock Sensor Part Number: 4671185
Product Specifications
- Other Name: Detonation Sensor; Ignition Knock (Detonation) Sensor; Front Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chrysler Town & Country | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
View related parts
Chrysler Town & Country Impact Sensor Part Number: 4637513
Product Specifications
- Other Name: Air Bag Impact (Insulation 4439082); Front Sensor; Stud Plate, W/Impact Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1991-1993 Chrysler Town & Country | Base | 6 Cyl 3.3 L GAS

Chrysler Town & Country Air Bag Sensor

Choose OEM Air Bag Sensor that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Air Bag Sensor follows strict manufacturing steps to lock in quality and fit. If your Chrysler Town & Country matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Town & Country parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Chrysler Town & Country Air Bag Sensor is unique input mechanism required to make Chrysler's popular minivan safe and dependable. This minimal crash sensor initially identifies the impacts and then instructs the control unit to initiate the execution of the air bags thus boosting the safety of passengers during accidents. Chrysler Town & Country is a large multi-purpose vehicle with a focus on comfort and numerous options; the Air Bag Sensor is incorporated into most models as the company pays significant attention to the car's performance characteristics. The Chrysler Town & Country Air Bag Sensor is a trusty component of the vehicle, which ought to protect the passengers, and it is always ready to respond in a crash. The need for these sensors is underlined by versatility in the reception of various Town & Country generations, thus keeping the sensor relevant after the car's modifications. In the same manner, the Air Bag Sensor promotes the safety as well as the functionality of the Chrysler Town & Country to make the drive as enjoyable as possible. More interesting features of the Air Bag Sensor are; It is able to determine the severity of the collision thus only; triggering the air bags when required thus limiting instances where the air-bags open thus causing harm. This kind of engineering makes the Chrysler Town & Country Air Bag Sensor one of the finest in the automotive market, the orientation for Chrysler that has always focused on safety and performance. In conclusion, Chrysler Town & Country Air Bag Sensor is a clear evidence that brands are willing to go an extra mile to ensure safe drive for families across the country.

Chrysler Town & Country Air Bag Sensor Parts and Q&A

Front Impact Sensor
4896011AB
Q: How to Service the Air Bag Sensor for Front Impact on Chrysler Town & Country?
A:
Unplug the negative battery cable and unhook the SRS first, as you shouldn't work on the system while the battery is connected. Never strike or allow the front impact sensor to fall, as it may be harmed or its calibration changed; a fallen sensor always needs to be replaced. Open the front impact sensors by climbing onto the engine compartment's top and going down below the inboard side of the front lamp unit's housing. Open the front collision system by removing the front end module wire from the left or right front impact sensor's connector receptacle. Take out the screw that holds the front impact sensor to the backing of the front end module carrier. Slide the front impact sensor backwards which will separate the pin inside from its hole in the front end module carrier and then remove the sensor from the front of the engine compartment. The front and third row side impact sensors can be placed in either set of side door panels.
Impact Sensor, Front
4896059AA
Q: How to Maintain Air Bag Sensors for Front and Side Impact on Chrysler Town & Country?
A:
Start by opening your hood and disconnecting the negative battery cable; then wait two minutes before resuming any work to avoid accidental deployment. After hoisting the car, remove the front impact sensor by sticking a hook under it and pulling, then disconnect the electrical connector and unfasten the two screws attaching it to the outer rails. Once the side impact sensors are mounted to the B-pillar, open the hood, disconnect the negative cable and allow two minutes of discharge. On the same side as the sensor, take out the lower trim where the B-pillar is found, pull out the electrical connector from the impact sensor and remove all the screws at the bracket before you remove it. If using sliding door opening sensors that are mounted sideways, once again open the hood, unhook the negative battery cable and then let the capacitor discharge for two minutes. Pull open the sliding door, undo the impact sensor's holding screws, unhook the connection wiring and remove the sensor from the vehicle. With the quarter panel mounted side impact sensors, lift the hood, unhook the negative battery cable and let the capacitor discharge for two minutes before you touch anything else. Open the quarter trim door where the old sensor is, take out its two hold down screws, disconnect the electrical cable and remove the sensor.