What Are the Steps and Safety Measures for Installing a Pressure Plate on Dodge Caliber?

First, put the clutch module onto the input shaft to install the pressure plate. After that, install the transaxle into the vehicle. Remember that DaimlerChrysler vehicles and replacement parts are made without asbestos; nevertheless, check aftermarket products for information on asbestos. Dust and dirt can build up on manual clutch components no matter what, so always handle and dispose of them in accordance with the necessary rules.

How to Handle a Pressure Plate When Removing and Installing a Disc Clutch on a 5.9 L Diesel with Dual Mass Flywheel on Dodge Ram 1500?

Stand the engine off the floor using a wood block and an adjustable jack stand to keep the mounts safe and, if you have one, take out the transmission and transfer case before removing the disc clutch. For a reusable pressure plate, mark its location on the flywheel with paint or a scriber and identify the respective location on the pressure plate with a L or circle with an X next to the holes. Place the matching hump helper through the pressure plate and pilot bushing as you remove the bolts. Release the bolts slowly, in a pattern as shown, then remove all the bolts and pull the pressure plate, disc and alignment tool away from the car. Always reset the pressure plate before fitting a clutch disc on a 5.9 L Diesel with Dual Mass Flywheel and self-adjusting pressure plate. Inspect the new clutch for proper operation and runout, put NLGI-2 rated grease in the crankshaft area and remember that the raised part of the tool must be facing out. Position the alignment tool in the pilot bearing and put the disc on the flywheel. Lay the pressure plate on top of the disc, line it up onto the flywheel and tighten down the bolts finger tight. Turn the bolt a little at a time, in a crisscross way, pressing them to the required torque less than a full turn for each, so the pressure plate cover is not damaged: V6 & V8 Engines should be torqued to 50 Nm (37 ft. lbs.) and V10 & Diesel Engines need 30 Nm (22 ft. lbs.) of torque. Remove both the release lever and release bearing from the clutch housing, put grease in the bore of the release bearing and spread some on both the contact spots between the release lever and the clutch housing and the release lever pivot stud. Coat the transmission input shaft splines with a light layer of Mopar high temperature bearing grease and brush a light coat onto the front bearing release surface. Clean the surface where the pilot bearing sits, then set the release lever and bearing in the housing of the clutch, making sure the spring clips that hold both together are all correct. The bottom of the lever, if fitted properly, should show the number stamped on it, facing right and with an "I" near the pivot ball end. While the car is up in the air, put in the transmission and transfer case if you have them and measure the fluid in the clutch master cylinder.

OEM Dodge Pressure Plate

Clutch Pressure Plate

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Pressure Plates found

View related parts
Dodge Pressure Plate Part Number: 68044869AA
$365.54 MSRP: $542.00
You Save: $176.46 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch Kit - Pressure Plate And Disc; Clutch Kit
- Replaces: V9900103
Fits the following Dodge Models:
- Dakota | 1997-1999 | Base, SLT, Sport | 3.9L V6, 6 Cyl 3.9 L GAS
View related parts
Dodge Pressure Plate Part Number: 5062025AE
$415.50 MSRP: $534.00
You Save: $118.50 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch - Modular; Clutch Kit
- Replaces: 5062025AB, 5062025AC, 5062025AD
Fits the following Dodge Models:
- Caliber | 2007-2009 | R/T, SE, SXT | 1.8L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Dodge Pressure Plate Part Number: 4668400AC
$268.52 MSRP: $397.00
You Save: $128.48 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Clutch - Modular
- Replaced by: 4668400AF
Fits the following Dodge Models:
- Neon | 1996-2000 | ACR, Base, ES, High Line, R/T, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Pressure Plate Part Number: 5062150AF
$450.84 MSRP: $685.00
You Save: $234.16 (35%)
ADD TO CART
Product Specifications
- Other Name: Clutch Kit - Pressure Plate And Disc; Clutch Kit
- Replaces: 5062150AD, 5062150AC, 5062150AE, 5062150AB
Fits the following Dodge Models:
- Caliber | 2007-2012 | Express, Heat, Mainstreet, R/T, Rush, SE, SRT-4, SXT, Uptown | 2.4L L4, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Journey | 2009-2010
View related parts
Dodge Pressure Plate Part Number: 5106042AD
$602.27 MSRP: $881.00
You Save: $278.73 (32%)
Product Specifications
- Other Name: Clutch - Modular; Clutch Kit
- Replaces: 5106042AB, 5106042AC
Fits the following Dodge Models:
- Avenger | 2008-2012
- Caliber | 2010-2012 | Express, Heat, Mainstreet, SE, SXT, SXT Plus, Uptown | 2.0L L4, 4 Cyl 2.0 L GAS
View related parts
Dodge Pressure Plate Part Number: MD749759
Product Specifications
- Other Name: Cover; Clutch Kit
Fits the following Dodge Models:
- Colt | 1993-1994 | Base, ES, GL | 4 Cyl 1.8 L GAS
View related parts
Dodge Pressure Plate Part Number: 5106018AD
Product Specifications
- Other Name: Clutch Kit - Pressure Plate And Disc; Clutch Kit
- Replaces: 5106018AA, 5106018AB, 5106018AC
Fits the following Dodge Models:
- Avenger | 2007-2009
- Caliber | 2007-2009 | R/T, SE, SRT-4, SXT | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
- Journey | 2009-2010
View More
View related parts
Dodge Pressure Plate Part Number: MD770039
Product Specifications
- Other Name: Clutch Pressure Plate, Clutch Kit
Fits the following Dodge Models:
- Colt | 1984-1994 | Base, DL, E, ES, GL, GT, Premier, Vista, Vista Custom | 4 Cyl 1.4 L GAS, 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Dodge Pressure Plate Part Number: 4797437
Product Specifications
- Other Name: Clutch - Disc & Pressure Plate; Clutch Kit
Fits the following Dodge Models:
- 600 | 1984-1988 | Base, ES, SE | 4 Cyl 2.2 L GAS, 4 Cyl 2.6 L GAS
- Aries | 1984-1985 | Base, Custom, LE, SE | 4 Cyl 2.2 L GAS, 4 Cyl 2.6 L GAS
- Caravan | 1989-1990 | Base, C/V, ES, LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Charger | 1985-1986 | Shelby | 4 Cyl 2.2 L GAS
- Daytona | 1984-1990 | Base, ES, ES Turbo, Pacifica, Shelby, Shelby Z, Turbo Z | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Grand Caravan | 1989-1990 | LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Lancer | 1985-1989 | Base, ES, Shelby | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
- Omni | 1985-1986 | GLH | 4 Cyl 2.2 L GAS
- Shadow | 1987-1990 | Base, ES, Shelby | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 4340298
Product Specifications
- Other Name: Clutch Kit
Fits the following Dodge Models:
- D100 | 1984-1987 | Custom | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1984-1987 | Base | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1984-1987 | Base | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1984-1987 | Base | 8 Cyl 5.9 L GAS
- Ramcharger | 1984-1987 | Base, Royal SE | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W100 | 1984-1987 | Custom | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W150 | 1984-1987 | Base | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W250 | 1984-1987 | Base | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W350 | 1984-1987 | Base | 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 4773799
Product Specifications
- Other Name: Clutch Package Present Plate & Disc; Clutch Kit
Fits the following Dodge Models:
- D150 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1992-1993 | Base | 8 Cyl 5.9 L GAS
- Ramcharger | 1992-1993 | Base, Canyon Sport, Royal SE | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W150 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W250 | 1992-1993 | Base | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- W350 | 1992-1993 | Base | 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 4797438AB
Product Specifications
- Other Name: Clutch; Clutch Release Bearing; Clutch Kit; Release Bearing; Disc
Fits the following Dodge Models:
- 600 | 1987-1988 | Base, SE | 4 Cyl 2.5 L GAS
- Aries | 1987-1989 | America, Base, LE | 4 Cyl 2.5 L GAS
- Caravan | 1988-1990, 1985-1986 | Base, C/V, ES, LE, SE | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Daytona | 1987-1990 | Base, ES | 4 Cyl 2.5 L GAS
- Grand Caravan | 1988-1990 | LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Lancer | 1987-1989 | Base, ES | 4 Cyl 2.5 L GAS
- Mini Ram | 1988, 1985-1986 | Base, Royal | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
- Shadow | 1988-1990 | Base, ES | 4 Cyl 2.5 L GAS
- Spirit | 1989-1991 | Base, ES, LE | 4 Cyl 2.5 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 2304A069
Product Specifications
- Other Name: Cover - Clutch; Clutch Kit
- Replaces: MR305949
Fits the following Dodge Models:
- Power Ram 50 | 1984-1986 | Custom, Royal, Sport | 4 Cyl 2.3 L DIESEL, 4 Cyl 2.6 L GAS
- Raider | 1987-1989 | Base | 4 Cyl 2.6 L GAS
- Ram 50 | 1984-1993 | Base, Custom, LE, Royal, SE, Sport | 4 Cyl 2.3 L DIESEL, 4 Cyl 2.4 L GAS, 4 Cyl 2.6 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 4626633AB
Product Specifications
- Other Name: Clutch - Disc & Pressure Plate
Fits the following Dodge Models:
- 600 | 1987-1988 | Base, SE | 4 Cyl 2.2 L GAS
- Daytona | 1987-1990 | Base, Pacifica, Shelby, Shelby Z | 4 Cyl 2.2 L GAS
- Lancer | 1987-1989 | Base, ES, Shelby | 4 Cyl 2.2 L GAS
- Shadow | 1987-1990 | Base, ES, Shelby | 4 Cyl 2.2 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 4511174AB
Product Specifications
- Other Name: Clutch; Clutch Kit; Disc
Fits the following Dodge Models:
- Daytona | 1991-1993 | Base, ES, Iroc | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Shadow | 1991-1994 | America, Base, ES, High Line | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Spirit | 1991-1993 | Base, ES, High Line, LE | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS
View More
View related parts
Dodge Pressure Plate Part Number: 4638411AB
Product Specifications
- Other Name: Clutch Package; Clutch Kit
- Replaces: V9900102
Fits the following Dodge Models:
- B150 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B250 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B350 | 1992-1993 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1990-1993 | 3.9L V6, 5.2L V8, 5.9L L6, 5.9L V8
- D250 | 1990-1993 | 3.9L V6, 5.2L V8, 5.9L L6, 5.9L V8
- D350 | 1990-1993 | 3.9L V6, 5.2L V8, 5.9L L6, 5.9L V8
- Dakota | 1990-1997 | Base, LE, S, SLT, Sport, WS | 2.5L L4, 3.9L V6, 5.2L V8, 6 Cyl 3.9 L GAS
- Ram 1500 | 1994-1996 | 3.9L V6, 5.2L V8
- Ram 2500 | 1994-1996 | 5.2L V8, 5.9L L6, 5.9L V8, 8.0L V10
- Ram 3500 | 1994-1996 | 5.9L L6, 5.9L V8, 8.0L V10
View More
View related parts
Dodge Pressure Plate Part Number: 5016562AB
Product Specifications
- Other Name: Clutch; Clutch Kit
Fits the following Dodge Models:
- Dakota | 2000 | Base, SLT, Sport | 6 Cyl 3.9 L GAS
View related parts
Dodge Pressure Plate Part Number: 5018591AA
Product Specifications
- Other Name: Clutch Kit - Pressure Plate And Disc; Clutch Kit
Fits the following Dodge Models:
- Dakota | 1994-2000 | Base, SLT, Sport, WS | 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS
View related parts
Dodge Pressure Plate Part Number: 4670116AB
Product Specifications
- Other Name: Clutch - Modular
Fits the following Dodge Models:
- Avenger | 1995-1999 | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Pressure Plate Part Number: 5037672AB
Product Specifications
- Other Name: Clutch - Modular; Clutch Kit
- Replaces: 5037672AA
Fits the following Dodge Models:
- Neon | 2005 | SRT-4 | 2.4L L4, 4 Cyl 2.4 L GAS

| Page 1 of 2 |Next >

1-20 of 25 Results

Dodge Pressure Plate

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Pressure Plate for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Pressure Plate is applied to squeeze the disc of the clutch, thus providing fast, crisp power changes each time. Born in a machine shop that was a dirty place to be, Dodge came up by welding steel bodies that were trembling with hits and stuffing cars with engines that threw drivers back into seats. The brand continued to drive, with Dodge releasing HEMI muscle, race-bred Viper excitement, and now even the mighty Fratzonic Chambered Exhaust that allows even the silent electrics to scream with 600 watts of artificial bang. Drag, Donut, Sport, or stealthy, Dodge allows drivers to switch gears and alter the character within seconds. Stay tough remains the slogan, although the badge is also a guarantee of fast entertainment and no-nonsense aesthetic that will pay back in inevitable everyday usage as much as on an outing. Within the manual drives of compacts up to the big sedans, the Pressure Plate to Dodge delivers a proven diaphragm spring to press the clutch disc against the flywheel, and the crankshaft torque is converted to uninterrupted forward motion without cramping the leg on the pedal. The balanced clamping force of the Pressure Plate allows the shift to remain smooth in stop-start traffic but is unable to relent when the revs increase during a spirited back-road blast. A rough-finished casing, thermal friction surface, and auto-adjusting travel make the Pressure Plate maintain a constant part-mile mile after mile, protecting gearboxes and increasing clutch life. The difference is felt by the driver as the Pressure Plate has a direct relationship between engine intent and wheel action with zero drama.

Dodge Pressure Plate Parts and Q&A

Pressure Plate
5062150AF
Q: What Are the Steps and Safety Measures for Installing a Pressure Plate on Dodge Caliber?
A:
First, put the clutch module onto the input shaft to install the pressure plate. After that, install the transaxle into the vehicle. Remember that DaimlerChrysler vehicles and replacement parts are made without asbestos; nevertheless, check aftermarket products for information on asbestos. Dust and dirt can build up on manual clutch components no matter what, so always handle and dispose of them in accordance with the necessary rules.
Pressure Plate
4848708AF
Q: How to Handle a Pressure Plate When Removing and Installing a Disc Clutch on a 5.9 L Diesel with Dual Mass Flywheel on Dodge Ram 1500?
A:
Stand the engine off the floor using a wood block and an adjustable jack stand to keep the mounts safe and, if you have one, take out the transmission and transfer case before removing the disc clutch. For a reusable pressure plate, mark its location on the flywheel with paint or a scriber and identify the respective location on the pressure plate with a L or circle with an X next to the holes. Place the matching hump helper through the pressure plate and pilot bushing as you remove the bolts. Release the bolts slowly, in a pattern as shown, then remove all the bolts and pull the pressure plate, disc and alignment tool away from the car. Always reset the pressure plate before fitting a clutch disc on a 5.9 L Diesel with Dual Mass Flywheel and self-adjusting pressure plate. Inspect the new clutch for proper operation and runout, put NLGI-2 rated grease in the crankshaft area and remember that the raised part of the tool must be facing out. Position the alignment tool in the pilot bearing and put the disc on the flywheel. Lay the pressure plate on top of the disc, line it up onto the flywheel and tighten down the bolts finger tight. Turn the bolt a little at a time, in a crisscross way, pressing them to the required torque less than a full turn for each, so the pressure plate cover is not damaged: V6 & V8 Engines should be torqued to 50 Nm (37 ft. lbs.) and V10 & Diesel Engines need 30 Nm (22 ft. lbs.) of torque. Remove both the release lever and release bearing from the clutch housing, put grease in the bore of the release bearing and spread some on both the contact spots between the release lever and the clutch housing and the release lever pivot stud. Coat the transmission input shaft splines with a light layer of Mopar high temperature bearing grease and brush a light coat onto the front bearing release surface. Clean the surface where the pilot bearing sits, then set the release lever and bearing in the housing of the clutch, making sure the spring clips that hold both together are all correct. The bottom of the lever, if fitted properly, should show the number stamped on it, facing right and with an "I" near the pivot ball end. While the car is up in the air, put in the transmission and transfer case if you have them and measure the fluid in the clutch master cylinder.