How to Maintain and Fix a Clutch Fork on Dodge Ram 1500?

Service or repair of the clutch release fork requires the removal of the transmission and transfer case if the vehicle is so equipped. After that, remove the spring clip (6) and safely remove the release bearing (4) from the release lever (3) before you get the bearing out. Look at the bearing slide surface on the transmission front retainer and change the retainer if it feels scored, worn, broken, cracked or warped. Check the release lever (2) and pivot stud (1) at the front and back side of the fork bottom to make sure the stud is stable and the lever is not twisted or damaged; if fork spring clips are bent or damaged at the steering head, replace them. Apply Mopar high temperature bearing grease to the input shaft splines, the bearing retainer side that slides, pivot stud (1) and the release lever pivot surface. Put the release fork and release bearing in place, using the spring clips to make sure they are held firmly and with the release lever raised so that the bump on its top is against the slave cylinder part of the transmission. Once all measurements are made, replace the transmission and transfer case throughout the vehicle.

How to Install a Clutch Fork on Dodge Ram 2500?

Make sure the clutch hydraulic tube is close to the dash panel, behind all its wiring and engine hoses, before installing the clutch release fork. Put a little grease on the inside of the master push rod, insert the clutch master cylinder into its bracket and tighten the nuts to 28 Nm (21 ft. lbs.). After that, set the clutch master cylinder push rod pin (3) in place and mount the clutch pedal position interlock switch connector (2). Hold the hydraulic line in place by clipping one plastic clip to the lower flange on the dash panel and the other to the upper stud. Holding the vehicle up still, fit the slave cylinder (2) at its proper place, ensure the rod is seated properly in the release lever and tighten the slave cylinder nuts (1) to an air torque setting of 23 Nm (17 ft. lbs.). If you're installing new clutch linkage, link the clutch hydraulic line to the clutch slave cylinder, reminding yourself not to take apart the line once connected. After that, place the heat shield over the hydraulic line and use the linkage several times to make sure everything is working properly.

OEM Dodge Clutch Fork

Release Fork

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Clutch Forks found

View related parts
Dodge Release Fork Part Number: 52107555AB
$45.00 MSRP: $66.95
You Save: $21.95 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Clutch Release; Clutch Fork; Lever Clutch Release
- Replaces: 52107555
Fits the following Dodge Models:
- B150 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B250 | 1992-1993 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B350 | 1992-1993 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1990-1993 | Base | 3.9L V6, 5.2L V8, 5.9L L6, 5.9L V8, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1990-1993 | Base | 3.9L V6, 5.2L V8, 5.9L L6, 5.9L V8, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1990-1993 | Base | 3.9L V6, 5.2L V8, 5.9L L6, 5.9L V8, 8 Cyl 5.9 L GAS
- Dakota | 1990-2009 | Base, Big Horn, Laramie, Lone Star, R/T, SLT, SLT Plus, ST, SXT, Sport, Sport Plus, TRX, TRX4, WS | 2.5L L4, 3.7L V6, 3.9L V6, 4 Cyl 2.5 L GAS, 4.7L V8, 5.2L V8, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- Nitro | 2007-2009 | R/T, SLT, SXT | 3.7L V6, 6 Cyl 3.7 L GAS, 6 Cyl 4.0 L GAS
- Ram 1500 | 1994-2008 | Base, LT, Laramie, SLT, SRT-10, SS/T 5.9L, ST, SXT, Sport, TRX4, WS | 10 Cyl 8.3 L GAS, 3.7L V6, 3.9L V6, 4.7L V8, 5.2L V8, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
- Ram 2500 | 1994-2008 | Base, Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 5.2L V8, 5.7L V8, 5.9L L6, 5.9L V8, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS, 8.0L V10
View More
View related parts
Dodge Release Fork Part Number: 4725612AA
$259.46 MSRP: $386.00
You Save: $126.54 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Clutch Release; Clutch Fork; Lever Clutch Release
Fits the following Dodge Models:
- Neon | 2003-2005 | SRT-4 | 4 Cyl 2.4 L GAS
View related parts
Dodge Release Fork Part Number: 52087515
$77.49 MSRP: $119.00
You Save: $41.51 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever - Clutch Release; Clutch Fork; Fork, Hydraulic Clutch Release W/3.9 L, 5.2 L, 5.9 L Engine; Lever Clutch Release
Fits the following Dodge Models:
- Ram 2500 | 2006-2010, 1994-2002 | Base, Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX, TRX4 | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 8 Cyl 5.7 L GAS
- Ram 3500 | 2006-2010, 1994-2002 | Base, Laramie, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL
View related parts
Dodge Release Fork Part Number: MD770510
$62.28 MSRP: $78.95
You Save: $16.67 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fork - Clutch Release
Fits the following Dodge Models:
- Stealth | 1991-1996 | Base | 6 Cyl 3.0 L GAS
View related parts
Dodge Release Fork Part Number: MD770506
$79.15 MSRP: $100.34
You Save: $21.19 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fork - Clutch Release
Fits the following Dodge Models:
- Colt | 1993-1994, 1989-1990 | Base, DL, E, ES, GL, GT, Vista | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Dodge Release Fork Part Number: MD749671
Product Specifications
- Other Name: Fork - Clutch Release; Fork Clutch Release
Fits the following Dodge Models:
- Stratus | 2001-2005 | R/T, SE | 6 Cyl 3.0 L GAS
View related parts
Dodge Release Fork Part Number: MD703275
Product Specifications
- Other Name: Fork - Fork, Clutch Release; Fork, Release, F, D Engine; Fork, Release, D Engine; Fork, Release
Fits the following Dodge Models:
- Conquest | 1984-1986 | Base | 4 Cyl 2.6 L GAS
- Raider | 1987-1989 | Base | 4 Cyl 2.6 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Release Fork Part Number: 4796665
Product Specifications
- Other Name: Lever - Clutch Release; Lever Package, W/Clip And Pivot Stud, Clutch Release; Lever Kit Clutch Release
Fits the following Dodge Models:
- Avenger | 1995-1999 | Base, ES | 4 Cyl 2.0 L GAS, 6 Cyl 2.5 L GAS
- Neon | 2001-2005, 1999 | ACR, Base, ES, High Line, SE, SXT, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Release Fork Part Number: 4796664
Product Specifications
- Other Name: Lever - Clutch Release; Lever Package, W/Clip And Pivot Stud, Clutch Release; Lever Package Clutch Release
Fits the following Dodge Models:
- Neon | 1995-2000 | ACR, Base, ES, High Line, R/T, Sport | 4 Cyl 2.0 L GAS
- Stratus | 1995-2000 | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Release Fork Part Number: MD770511
Product Specifications
- Other Name: Fork - Clutch Release; Clutch Fork
Fits the following Dodge Models:
- Stealth | 1991-1996 | ES, R/T, R/T Turbo | 6 Cyl 3.0 L GAS
View related parts
Dodge Release Fork Part Number: MB837152
Product Specifications
- Other Name: Fork Clutch Release; Clutch Fork; Fork, Clutch Release; Fork
Fits the following Dodge Models:
- Stealth | 1991-1996 | ES, R/T, R/T Turbo | 6 Cyl 3.0 L GAS
View related parts
Dodge Release Fork Part Number: 4511046
Product Specifications
- Other Name: Fork - Clutch Release; Clutch Fork; Fork, Clutch Release
Fits the following Dodge Models:
- Caravan | 1992-1994, 1990 | Base, C/V, ES, LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L CNG, 6 Cyl 3.3 L GAS
- Daytona | 1990-1993 | Base, ES, ES Turbo, Iroc, Iroc R/T, Shelby | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Grand Caravan | 1992-1994, 1990 | Base, ES, LE, SE | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Omni | 1990 | Base | 4 Cyl 2.2 L GAS
- Shadow | 1990-1994 | America, Base, ES, High Line | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Spirit | 1990-1993 | Base, ES, High Line, LE, R/T | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View More

Dodge Clutch Fork

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Clutch Fork for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

The Dodge Clutch Fork transforms foot movement into a positive aggressive action of engaging the clutch to make every shift swift and confident. The pursuit of power has been in Dodge since its all-steel bodies dashed out in 1914, outperforming the heavier competitors. Dodge is looking to live the fast life with bold styling, HEMI muscle and crazy Viper project. In the new Fratzonic Chambered Exhaust cranks, the sound of thunder comes in a 600-watt stack such that even the electric offerings retain the muscle attitude that Dodge fans desire. Drag or Stealth adaptive drive modes allow Dodge drivers to switch between disarming drama on the curb to silent cruise in a few seconds. The heritage of working machine shops can be felt in the brand in each panel and powertrain. Clutch Fork rides have been placed in the center of the manual drive system, which will move to push the release bearing every time your foot drops. Clutch Fork will take hydraulic or mechanical linkages, and thus an upgrade or a swap will be installed with ease. Clutch Fork is found to be resistant to fatigue during repeated full throttle takeoffs and hustle-stop traffic as well. When a Clutch Fork bends or cracks, the shift feel becomes vague and the clutch may never disengage, and it is possible to lose all the drive.

Dodge Clutch Fork Parts and Q&A

Release Fork
52107555AB
Q: How to Maintain and Fix a Clutch Fork on Dodge Ram 1500?
A:
Service or repair of the clutch release fork requires the removal of the transmission and transfer case if the vehicle is so equipped. After that, remove the spring clip (6) and safely remove the release bearing (4) from the release lever (3) before you get the bearing out. Look at the bearing slide surface on the transmission front retainer and change the retainer if it feels scored, worn, broken, cracked or warped. Check the release lever (2) and pivot stud (1) at the front and back side of the fork bottom to make sure the stud is stable and the lever is not twisted or damaged; if fork spring clips are bent or damaged at the steering head, replace them. Apply Mopar high temperature bearing grease to the input shaft splines, the bearing retainer side that slides, pivot stud (1) and the release lever pivot surface. Put the release fork and release bearing in place, using the spring clips to make sure they are held firmly and with the release lever raised so that the bump on its top is against the slave cylinder part of the transmission. Once all measurements are made, replace the transmission and transfer case throughout the vehicle.
Release Fork
52087515
Q: How to Install a Clutch Fork on Dodge Ram 2500?
A:
Make sure the clutch hydraulic tube is close to the dash panel, behind all its wiring and engine hoses, before installing the clutch release fork. Put a little grease on the inside of the master push rod, insert the clutch master cylinder into its bracket and tighten the nuts to 28 Nm (21 ft. lbs.). After that, set the clutch master cylinder push rod pin (3) in place and mount the clutch pedal position interlock switch connector (2). Hold the hydraulic line in place by clipping one plastic clip to the lower flange on the dash panel and the other to the upper stud. Holding the vehicle up still, fit the slave cylinder (2) at its proper place, ensure the rod is seated properly in the release lever and tighten the slave cylinder nuts (1) to an air torque setting of 23 Nm (17 ft. lbs.). If you're installing new clutch linkage, link the clutch hydraulic line to the clutch slave cylinder, reminding yourself not to take apart the line once connected. After that, place the heat shield over the hydraulic line and use the linkage several times to make sure everything is working properly.