How to Install an Antenna Cable and Its Components on Jeep Wrangler?

First put in the satellite cable, then the instrument panel speaker, the glove box and at last the cowl trim. After that, set the lower B-pillar trim, the top piece and attach the negative cable to your battery as the final step.

How to Replace an Antenna Cable and Its Body on Jeep Grand Cherokee?

To start replacing the antenna body and cable, remove the air bag system's negative battery cable, wait two minutes to allow it to discharge, then attach the antenna. First, take out the scuff plate at the front right door sill and the trim panel at the right inner cowl side. Grab the connector under the passenger side of the instrument panel on the right side inner panel and twist it apart without pulling on the coaxial cable. You should then take out the bottom part of the inner liner on the right front fender wheel house and reach the antenna lead grommet from the rear of the opening in that fender. Take out the coaxial antenna line and connector from the car through the hole on the right cowl side outer side panel, into the right front fender wheel house. Raise the antenna mast, remove the shroud from the antenna cap nut with your fingers and then use the Special Tool C-4816 to take out the cap nut. Take off the antenna plate from the antenna base above the right front fender and lift the base from its hole in the top of the front fender. Remove both the antenna base and its lead cable through the opening in the rear of the right front fender wheel house opening. For assembly, slide the antenna assembly into place in the opening beneath the far right front wheel and push the base into the connecting spot in the fender. Put the antenna escutcheon on the antenna base, after which you install the antenna base cap nut and tighten it to 6.8 Nm (60 in. lbs.) using the antenna nut wrench (Special Tool C-4816). After that, fit the plastic shroud over the antenna base cap nut and tighten the antenna mast to the antenna base at 3.3 Nm (30 in. lbs.). Push the antenna lead coaxial cable and its connector from the rear of the right fender until it is seated firmly through the hole in the right cowl side outer panel, then set the grommet inside that hole. Slide the lower section of the inner liner down into the left wheel house, plug in the antenna coaxial connectors and fit the trim panel onto the inner cowl and the scuff plate onto the front door sill. At the end, attach the battery negative cable once more.

OEM Jeep Antenna Cable

Radio Antenna Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

90 Antenna Cables found

View related parts
Jeep Antenna, Black Part Number: 1YG06AXRAF
$190.34 MSRP: $295.00
You Save: $104.66 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
- Replaces: 1YG06AXRAC, 1YG06AXRAE, 1YG06AXRAD, 1YG06AXRAB
Fits the following Jeep Models:
- Grand Cherokee | 2017, 2014 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna Cable Part Number: 68487090AA
$155.22 MSRP: $238.00
You Save: $82.78 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Cable & Base Assembly; Radio Antenna Assembly; Radio Antenna Base; Antenna Base; Base; Antenna; Antenna Cable & Base Assembly
- Replaces: 5091873AA, 68320426AA
Fits the following Jeep Models:
- Cherokee | 2016-2023 | 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
- Compass | 2017-2025 | 80th Anniversary, Altitude, High Altitude, Latitude, Latitude Lux, Limited, Red, Sport, Trailhawk, Upland | 2.4L L4, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS
View related parts
Jeep Cable Part Number: 56040948AG
$27.55 MSRP: $42.15
You Save: $14.60 (35%)
ADD TO CART
Product Specifications
- Other Name: Antenna; Antenna Cable; Cable Antenna
- Replaces: 56040948AF
Fits the following Jeep Models:
- Wrangler | 2012-2017 | 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 3.6L V6, 6 Cyl 3.6 L GAS
- Wrangler JK | 2018 | Rubicon, Sahara, Sport, Sport S, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 6 Cyl 3.6 L GAS
View related parts
Jeep Antenna Part Number: 5091972AC
$76.93 MSRP: $91.65
You Save: $14.72 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Base; Antenna Cable; Wire; Antenna Base Cable And Bracket
- Replaces: 5091972AB, 5091972AA
Fits the following Jeep Models:
- Cherokee | 2014 | Latitude, Limited, Sport, Trailhawk | 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
View related parts
Jeep Antenna, Billet Silver Part Number: 6ZP28JSCAA
$132.56 MSRP: $209.00
You Save: $76.44 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
- Replaces: 6DE46JSCAA
Fits the following Jeep Models:
- Grand Cherokee | 2018-2021 | 80th Anniversary, Altitude, High Altitude, Laredo, Laredo E, Laredo X, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, Billet Silver/Gray Part Number: 1YG06JSCAF
$190.34 MSRP: $295.00
You Save: $104.66 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
- Replaces: 1YG06JSCAC, 1YG06JSCAB, 1YG06JSCAE, 1YG06JSCAD
Fits the following Jeep Models:
- Grand Cherokee | 2017, 2014 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna Part Number: 1YG06LAUAF
$190.34 MSRP: $295.00
You Save: $104.66 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
- Replaces: 1YG06LAUAD, 1YG06LAUAB, 1YG06LAUAC, 1YG06LAUAE
Fits the following Jeep Models:
- Grand Cherokee | 2017, 2014 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, Ivory White Part Number: 5XT13JWDAA
$66.17 MSRP: $97.35
You Save: $31.18 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2017-2020 | Altitude, High Altitude, Laredo, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna Part Number: 5XT13SHRAA
$66.17 MSRP: $97.35
You Save: $31.18 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2018-2020 | Altitude, High Altitude, Laredo, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, Pearl Red Part Number: 5LQ48JRMAB
$88.35 MSRP: $127.00
You Save: $38.65 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket AM/FM/Gps; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2017-2020 | Altitude, High Altitude, Laredo, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, Diamond Black Part Number: 5XT13KXJAA
$79.31 MSRP: $106.00
You Save: $26.69 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2018-2020 | Altitude, High Altitude, Laredo, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, Diamond Black Part Number: 6ZP28KXJAA
$132.56 MSRP: $209.00
You Save: $76.44 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket Sharkfin; Antenna Base Cable And Bracket
- Replaces: 68306633AA, 6DE46KXJAA
Fits the following Jeep Models:
- Cherokee | 2019-2023 | 80th Anniversary, Altitude, Altitude Lux, High Altitude, Latitude, Latitude Lux, Latitude Plus, Limited, Overland, Trailhawk, Trailhawk Elite, Upland, X | 2.0L L4, 2.4L L4, 3.2L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.2 L GAS
- Grand Cherokee | 2018-2020 | Altitude, High Altitude, Laredo, Limited, Limited X, Overland, SRT, Summit, Trackhawk, Trailhawk, Upland | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.2L V8, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
- Grand Wagoneer | 2022-2023 | Base, Obsidian, Series I, Series II, Series III, Series III Obsidian | 6 Cyl 3.0 L GAS, 8 Cyl 6.4 L GAS
- Grand Wagoneer L | 2023 | Base, Obsidian, Series II, Series III, Series III Obsidian | 6 Cyl 3.0 L GAS
- Wagoneer | 2022-2023 | Base, Carbide, Series I, Series I Carbide, Series II, Series II Carbide, Series III, Series III Carbide | 6 Cyl 3.0 L GAS, 8 Cyl 5.7 L MILD HYBRID EV-GAS (MHEV)
- Wagoneer L | 2023 | Base, Carbide, Series II, Series III | 6 Cyl 3.0 L GAS
View More
View related parts
Jeep Antenna Cable Part Number: 56038716AC
Product Specifications
- Other Name: Cable - Antenna; Cable Antenna
Fits the following Jeep Models:
- Grand Cherokee | 2005 | Laredo, Limited | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Antenna, Ivory White Part Number: 1YG06JWDAF
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2017 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna Cable Part Number: 56038513AF
Product Specifications
- Other Name: Cable - Antenna; Body & Cable; Cable Antenna
Fits the following Jeep Models:
- Grand Cherokee | 1999-2001 | Laredo, Limited | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
Jeep Antenna Cable Part Number: 56038716AD
Product Specifications
- Other Name: Cable - Antenna; Cable Antenna
Fits the following Jeep Models:
- Grand Cherokee | 2006-2007 | 65th Anniversary Edition, Laredo, Limited, Overland, SRT8 | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Antenna Cable Part Number: 5064713AA
Product Specifications
- Other Name: Cable - Satellite Radio; Cable Satellite Radio
- Replaces: 5064425AA, 5064355AB, 5064355AA
Fits the following Jeep Models:
- Grand Cherokee | 2008-2010 | Laredo, Limited, Overland, SRT8 | 3.0L V6, 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 6.1L V8, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Antenna, Luxury Brown Part Number: 5XT13GTWAA
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2017 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, Brown Part Number: 1YG06GTWAF
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
Fits the following Jeep Models:
- Grand Cherokee | 2017 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Antenna, True Blue Part Number: 1YG06KBUAF
Product Specifications
- Other Name: Antenna - Base Cable And Bracket; Radio Antenna Assembly; Antenna Base Cable And Bracket
- Replaces: 1YG06KBUAD, 1YG06KBUAB, 1YG06KBUAC, 1YG06KBUAE
Fits the following Jeep Models:
- Grand Cherokee | 2017, 2014 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 3.0L V6, 3.6L V6, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS

| Page 1 of 5 |Next >

1-20 of 90 Results

Jeep Antenna Cable

OEM parts sourced directly from Jeep deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Jeep Antenna Cable for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Jeep Antenna Cable is applied to keep your radio signals clear in the wild routing without dropped signals. Stemmed out of wartime toughness, Jeep became a symbol that drivers rely on when the road pavement runs out. Its square glasses roll off boulders, ridges, and gullies, and detachable tops welcome sun and mud. Traction can be switched to snow, sand, or slick clay in just a couple of seconds. A sharp cab display now gives maps, voice instructions, and on-air updates that focus each excursion. Couples connect through trails and forums, swapping tips and exchanging parts since the rig punishes non-tinkering. Durability remains the north star, thus Jeep imparts tough steel with tech that hardly gives up. You can hike a creek at daybreak and take the commute to town at noon, evidence that Jeep is not compromising. The Antenna Cable was constructed with a tight shielding and low-loss wiring that helps in combating the problem of static, moisture resistance, and helping to keep AM, FM, and satellite bands alive when other connectors suffer corrosion. Antenna Cable is installed behind dash panels with no cuts and locked to factory mounts with a solid snap. That replacement makes any Jeep radio clearer since the feed is pure and uninterrupted through the Antenna Cable. Select the appropriate length of Antenna Cable and you will not have slack to whip around the place or tension to wear through.

Jeep Antenna Cable Parts and Q&A

Cable
5064159AG
Q: How to Install an Antenna Cable and Its Components on Jeep Wrangler?
A:
First put in the satellite cable, then the instrument panel speaker, the glove box and at last the cowl trim. After that, set the lower B-pillar trim, the top piece and attach the negative cable to your battery as the final step.
Antenna Cable
56038617AB
Q: How to Replace an Antenna Cable and Its Body on Jeep Grand Cherokee?
A:
To start replacing the antenna body and cable, remove the air bag system's negative battery cable, wait two minutes to allow it to discharge, then attach the antenna. First, take out the scuff plate at the front right door sill and the trim panel at the right inner cowl side. Grab the connector under the passenger side of the instrument panel on the right side inner panel and twist it apart without pulling on the coaxial cable. You should then take out the bottom part of the inner liner on the right front fender wheel house and reach the antenna lead grommet from the rear of the opening in that fender. Take out the coaxial antenna line and connector from the car through the hole on the right cowl side outer side panel, into the right front fender wheel house. Raise the antenna mast, remove the shroud from the antenna cap nut with your fingers and then use the Special Tool C-4816 to take out the cap nut. Take off the antenna plate from the antenna base above the right front fender and lift the base from its hole in the top of the front fender. Remove both the antenna base and its lead cable through the opening in the rear of the right front fender wheel house opening. For assembly, slide the antenna assembly into place in the opening beneath the far right front wheel and push the base into the connecting spot in the fender. Put the antenna escutcheon on the antenna base, after which you install the antenna base cap nut and tighten it to 6.8 Nm (60 in. lbs.) using the antenna nut wrench (Special Tool C-4816). After that, fit the plastic shroud over the antenna base cap nut and tighten the antenna mast to the antenna base at 3.3 Nm (30 in. lbs.). Push the antenna lead coaxial cable and its connector from the rear of the right fender until it is seated firmly through the hole in the right cowl side outer panel, then set the grommet inside that hole. Slide the lower section of the inner liner down into the left wheel house, plug in the antenna coaxial connectors and fit the trim panel onto the inner cowl and the scuff plate onto the front door sill. At the end, attach the battery negative cable once more.