How to Safely Service the Air Bag Control Module on Jeep Wrangler?

Prior to servicing Air Bag Control Module, you must disable the Supplemental Restraint System by breaking the power circuit with the battery negative cable and waiting two minutes for the system capacitor to discharge. You shouldn't strike or drop the occupant restraint controller, because it might harm the impact sensor and make you buy a new module. If your car is fitted with Occupant Classification System, do not replace both the Occupant Restraint Controller and the Occupant Classification Module all at once. First replace only one of them and perform the confirmation test before adding the other one to avoid setting up a lasting fault. When removing the battery start by disconnecting the negative cable and allow the capacitor to completely discharge. After that, take out the center console from the roof of the floor panel transmission tunnel. Press the release tab and raise the lever arm on every connector to release both the wire harnesses at the ORC on the right of the module. After that, take out the four nuts holding the ORC to the ORC mount welded onto the top of the floor panel transmission tunnel, then remove the entire ORC from the mount.

How to Safely Diagnose or Service the Air Bag Control Module on Jeep Cherokee?

The impact sensor in the air bag Control Module allows air bags to deploy, so make sure to disconnect the battery negative cable and wait for about two minutes, so the capacitor will be empty. Be sure to avoid hitting or kicking the air bag Control Module, since this destroy the impact sensor and could hurt its proper calibration. Always attach the protective cover on the air bag Control Module to keep it from falsely or accidentally deploying. First, remove the negative battery cable, then lift the center console from its place in the floor tunnel and finally unplug the rear duct. Once that's done, unscrew the three fasteners at the back of the center floor console and take out the bracket. Pull the air bag Control Module connector straight out by squeezing the tabs on its harness in the panel. Take the three nuts out that are securing the module to the weld studs on the mounting bracket, then pull the module off. Line the module up on the bracket so the arrow on the label points the way you want it and tighten the screws to 7.3 Nm (65 in. lbs.) Securely attach the instrument panel wire harness connector, pushing both latches in place. Put the center floor console rear mounting bracket over the module, then use three screws and tighten them to 1.1 Nm (10 in. lbs.). attach the floor console and afterward place the rear vent console. Do not attach the negative cable from the battery when replacing it; first comply with the air bag instructions.

OEM Jeep Air Bag Control Module

SRS Airbag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

144 Air Bag Control Modules found

View related parts
Jeep SDM Module Part Number: 68031601AC
$307.04 MSRP: $457.00
You Save: $149.96 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 68031601AB, 68031601AA
Fits the following Jeep Models:
- Wrangler | 2008-2010 | Rubicon, Sahara, Sport, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 6 Cyl 3.8 L GAS
View related parts
Jeep SDM Module Part Number: 68148024AA
$275.15 MSRP: $421.00
You Save: $145.85 (35%)
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 56054301AC, 56054301AB
Fits the following Jeep Models:
- Wrangler | 2010-2012 | 70th Anniversary, Rubicon, Sahara, Sport, Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 3.6L V6, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
View related parts
Jeep SDM Module Part Number: 68526680AB
$270.79 MSRP: $403.00
You Save: $132.21 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Diagnostic Unit
Fits the following Jeep Models:
- Wrangler | 2022-2023 | Unlimited Rubicon 392 | 8 Cyl 6.4 L GAS
View related parts
Jeep SDM Module Part Number: 68526673AA
$303.88 MSRP: $459.00
You Save: $155.12 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Diagnostic Unit
- Replaces: 68437718AA, 68400422AA, 68437718AB, 68400422AB, 68398609AA, 68398609AB
Fits the following Jeep Models:
- Wrangler | 2018-2023 | 80th Anniversary, Freedom, Islander, Rubicon, Sport, Sport S, Unlimited 80th Anniversary, Unlimited Freedom, Unlimited High Altitude, Unlimited High Tide, Unlimited Islander, Unlimited Moab, Unlimited Rubicon, Unlimited Sahara, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Willys, Unlimited Willys Sport, Willys, Willys Sport | 2.0L L4, 3.0L V6, 3.6L V6, 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L MILD HYBRID EV-GAS (MHEV)
View related parts
Jeep SDM Module Part Number: 68631463AA
$236.80 MSRP: $351.00
You Save: $114.20 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint
- Replaces: 68621852AA
Fits the following Jeep Models:
- Grand Cherokee | 2022-2024 | 30th Anniversary 4xe, 4xe, Altitude, Laredo, Limited, Overland, Summit, Summit Reserve, Trailhawk | 2.0L L4, 3.6L V6, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 5.7L V8
View related parts
Jeep SDM Module Part Number: 68621834AA
$719.36 MSRP: $1085.00
You Save: $365.64 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint
- Replaces: 68360916AD, 68565965AB, 68565965AC, 68565965AD, 68360916AE, 68360916AC, 68565965AA
Fits the following Jeep Models:
- Grand Cherokee | 2022-2024 | 30th Anniversary 4xe, 4xe, Altitude, Altitude X, Laredo, Laredo X, Limited, Overland, Summit, Summit Reserve, Trailhawk | 2.0L L4, 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX
View related parts
Jeep SDM Module Part Number: 68526670AB
$296.85 MSRP: $442.00
You Save: $145.15 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Diagnostic Unit
- Replaces: 68526670AA
Fits the following Jeep Models:
- Wrangler | 2021-2023 | Unlimited High Altitude 4xe, Unlimited Rubicon 4xe, Unlimited Sahara 4xe, Unlimited Willys 4xe | 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Jeep SDM Module Part Number: 68046003AD
$179.01 MSRP: $267.00
You Save: $87.99 (33%)
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 68046003AA, 68046003AC, 68046003AB
Fits the following Jeep Models:
- Wrangler | 2010-2011 | 70th Anniversary, Rubicon, Sahara, Sport, Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, X | 6 Cyl 3.8 L GAS
View related parts
Jeep SDM Module Part Number: 68526674AA
$265.12 MSRP: $395.00
You Save: $129.88 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Diagnostic Unit
Fits the following Jeep Models:
- Wrangler | 2022-2023 | Unlimited High Altitude, Unlimited Rubicon, Unlimited Sahara, Unlimited Sahara Altitude, Unlimited Sport, Unlimited Sport Altitude, Unlimited Sport S, Unlimited Willys, Unlimited Willys Sport | 6 Cyl 3.0 L DIESEL
View related parts
Jeep Control Module Part Number: 56010426AJ
$274.81 MSRP: $408.00
You Save: $133.19 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module; Occupant Module; Module Occupant Restraint
- Replaces: 56010426AI, 56010426AH, 56010426AG
Fits the following Jeep Models:
- Grand Cherokee | 2005 | Laredo, Limited | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Control Module, Front Part Number: 68459138AE
$82.71 MSRP: $122.00
You Save: $39.29 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module, Front; SDM Module
- Position: Front
- Replaces: 68459138AD, 68459138AC
Fits the following Jeep Models:
- Grand Cherokee | 2022 | Overland, Summit, Summit Reserve, Trailhawk | 8 Cyl 5.7 L GAS
View related parts
Jeep SDM Module Part Number: 68046001AD
$137.15 MSRP: $207.00
You Save: $69.85 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 68046001AA, 68046001AC, 68046001AB
Fits the following Jeep Models:
- Wrangler | 2010-2011 | 70th Anniversary, Rubicon, Sahara, Sport, Unlimited 70th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited X, X | 6 Cyl 3.8 L GAS
View related parts
Jeep SDM Module Part Number: 68185856AB
$214.14 MSRP: $319.00
You Save: $104.86 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Module Occupant Restraint
Fits the following Jeep Models:
- Wrangler | 2013-2017 | 75th Anniversary, Rubicon, Sahara, Sport, Sport S, Unlimited 75th Anniversary, Unlimited Rubicon, Unlimited Sahara, Unlimited Sport, Unlimited Sport S | 6 Cyl 3.6 L GAS
View related parts
Jeep Control Module Part Number: 56010533AA
Product Specifications
- Other Name: Module - Air Bag Control; Air Bag Control Module; Module Air Bag Control
- Replaces: 56010300AC
Fits the following Jeep Models:
- Wrangler | 2001-2006 | 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 2.4L L4, 2.5L L4, 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 4.0L L6, 6 Cyl 4.0 L GAS
View related parts
Jeep Control Module Part Number: 68309533AA
$474.03 MSRP: $690.00
You Save: $215.97 (32%)
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; SDM Module; Module Occupant Restraint
Fits the following Jeep Models:
- Grand Cherokee | 2017 | Laredo, Limited, Overland, SRT, Summit, Trailhawk | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Control Module Part Number: 56010425AJ
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module; Occupant Module; Module Occupant Restraint
- Replaces: 56010425AG, 56010425AH, 56010425AI
Fits the following Jeep Models:
- Grand Cherokee | 2005 | Laredo, Limited | 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep Diagnostic Unit Part Number: 68003221AC
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module
- Replaces: 68003221AB, 68003221AA
Fits the following Jeep Models:
- Wrangler | 2007 | Rubicon, Sahara, X | 3.8L V6, 6 Cyl 3.8 L GAS
View related parts
Jeep SDM Module Part Number: 68025654AK
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Seat Sensor Mat; Occupant Module
- Replaces: 68025654AG, 68025654AJ, 68025654AI, 68025654AH
Fits the following Jeep Models:
- Grand Cherokee | 2011-2013 | Laredo, Limited, Overland, Overland Summit, SRT8 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
View related parts
Jeep Control Module Part Number: 4896901AE
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Passenger Presence Module; Occupant Module
- Replaces: 4896901AB, 4896901AD
Fits the following Jeep Models:
- Grand Cherokee | 2007 | Laredo, Limited, Overland | 3.0L V6, 3.7L V6, 4.7L V8, 5.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Jeep SDM Module Part Number: 68025632AK
Product Specifications
- Other Name: Module - Occupant Restraint; Module Occupant Restraint
- Replaces: 68025632AJ, 68025632AI, 68025632AG, 68025632AH
Fits the following Jeep Models:
- Grand Cherokee | 2011-2012 | Laredo, Limited, Overland, Overland Summit, SRT8 | 3.6L V6, 5.7L V8, 6 Cyl 3.6 L FLEX, 6.4L V8, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS

| Page 1 of 8 |Next >

1-20 of 144 Results

Jeep Air Bag Control Module

OEM parts sourced directly from Jeep deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Jeep Air Bag Control Module for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Jeep Air Bag Control Module activates airbags immediately when its sensors record the occurrence of a severe crash. Jeep is a mud, mountain, and unpaved shortcut SUV. Since the introduction of the civilian version in 1945, the brand retained the military-level base but welcomed weekend campers to ride aboard. Selec-Terrain allows motorists to turn a knob and immediately change the power, traction, and throttle to snow, sand, or slick clay. Durable steel skid plates roll off the strikes of rocks, and removable doors give the wind and view to the hand of the drivers. Jeep lives in a worldwide tribe that shares trail tips, gestures at stoplights, and makes parking lots their narrative pits. The voice control, bright touch screens, and the ability to update itself over the air give the vehicle city prowess without eroding the rock-crawl spirit of the vehicle. Under normal driving conditions, the Air Bag Control Module would allow Jeep to perform endless self-tests on sensors, seatbelt conditions, and impact tolerance and calculate deployment actions in milliseconds to be unforgivingly realistic on the road. The Air Bag Control Module is a real-time crash pulse monitoring module that memorizes impact data to be analyzed later. Whenever chaos hits, the Air Bag Control Module of Jeep believes that the correct bags will be thrown, the fuel will be cut off, and the hazard lights will be flashing in front of your eyes without you even blinking. Subsequently, the Air Bag Control Module stores fault codes and performs one more round of diagnostics to ensure that the system remains battle ready.

Jeep Air Bag Control Module Parts and Q&A

SDM Module
68003421AC
Q: How to Safely Service the Air Bag Control Module on Jeep Wrangler?
A:
Prior to servicing Air Bag Control Module, you must disable the Supplemental Restraint System by breaking the power circuit with the battery negative cable and waiting two minutes for the system capacitor to discharge. You shouldn't strike or drop the occupant restraint controller, because it might harm the impact sensor and make you buy a new module. If your car is fitted with Occupant Classification System, do not replace both the Occupant Restraint Controller and the Occupant Classification Module all at once. First replace only one of them and perform the confirmation test before adding the other one to avoid setting up a lasting fault. When removing the battery start by disconnecting the negative cable and allow the capacitor to completely discharge. After that, take out the center console from the roof of the floor panel transmission tunnel. Press the release tab and raise the lever arm on every connector to release both the wire harnesses at the ORC on the right of the module. After that, take out the four nuts holding the ORC to the ORC mount welded onto the top of the floor panel transmission tunnel, then remove the entire ORC from the mount.
Control Module
56007323AE
Q: How to Safely Diagnose or Service the Air Bag Control Module on Jeep Cherokee?
A:
The impact sensor in the air bag Control Module allows air bags to deploy, so make sure to disconnect the battery negative cable and wait for about two minutes, so the capacitor will be empty. Be sure to avoid hitting or kicking the air bag Control Module, since this destroy the impact sensor and could hurt its proper calibration. Always attach the protective cover on the air bag Control Module to keep it from falsely or accidentally deploying. First, remove the negative battery cable, then lift the center console from its place in the floor tunnel and finally unplug the rear duct. Once that's done, unscrew the three fasteners at the back of the center floor console and take out the bracket. Pull the air bag Control Module connector straight out by squeezing the tabs on its harness in the panel. Take the three nuts out that are securing the module to the weld studs on the mounting bracket, then pull the module off. Line the module up on the bracket so the arrow on the label points the way you want it and tighten the screws to 7.3 Nm (65 in. lbs.) Securely attach the instrument panel wire harness connector, pushing both latches in place. Put the center floor console rear mounting bracket over the module, then use three screws and tighten them to 1.1 Nm (10 in. lbs.). attach the floor console and afterward place the rear vent console. Do not attach the negative cable from the battery when replacing it; first comply with the air bag instructions.