How to Service and Install a Throttle Position Sensor on 2004 Dodge Dakota?

First, you should unhook the TPS electrical connector, remove the two screws used to secure the sensor and finally, remove the Throttle Position Sensor (TPS). For installation, after connecting the throttle body end to the TPS, verify the throttle shaft moves a little; if it does not, put the sensor in the other way so it slides on the opposite end of the sensor tangs. TPS will experience slight tension when you rotate it. Put the TPS in its position, then install and tighten the retaining screws to 7 Nm (60 in. Lbs.). Once the TPS electrical connector is hooked back up, rev the throttle a few times by hand to make sure everything in the TPS operates freely before you start the engine. Afterward, put the air cleaner tube into the throttle body.

OEM 2004 Dodge Dakota Throttle Position Sensor

TPS Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Throttle Position Sensors found

View related parts
2004 Dodge Dakota Throttle Position Sensor Part Number: 68404428AA
$61.51 MSRP: $85.05
You Save: $23.54 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Throttle Position; Throttle Positionition Sensor; Throttle Sensor
- Replaces: 5019411AD, 5019411AB, 5019411AC
- Item Weight: 0.60 Pounds
- Item Dimensions: 2.0 x 2.0 x 2.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 68404428AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Dakota Submodels:
- Base, Laramie, SLT, SLT Plus, ST, SXT, Sport, Sport Plus | 3.7L V6, 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
2004 Dodge Dakota Throttle Position Sensor Part Number: 5017479AA
Product Specifications
- Other Name: Sensor - Throttle Position; Throttle Positionition Sensor; Throttle Sensor; Sensor Kit Throttle Position
- Replaces: 4882219
- Item Weight: 0.60 Pounds
- Item Dimensions: 1.9 x 2.7 x 3.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5017479AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2004 Dodge Dakota Submodels:
- Base, Laramie, R/T, SLT, SLT Plus, ST, SXT, Sport, Sport Plus | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS

2004 Dodge Dakota Throttle Position Sensor Parts and Q&A

Q: How to Service and Install a Throttle Position Sensor on 2004 Dodge Dakota?
A: First, you should unhook the TPS electrical connector, remove the two screws used to secure the sensor and finally, remove the Throttle Position Sensor (TPS). For installation, after connecting the throttle body end to the TPS, verify the throttle shaft moves a little; if it does not, put the sensor in the other way so it slides on the opposite end of the sensor tangs. TPS will experience slight tension when you rotate it. Put the TPS in its position, then install and tighten the retaining screws to 7 Nm (60 in. Lbs.). Once the TPS electrical connector is hooked back up, rev the throttle a few times by hand to make sure everything in the TPS operates freely before you start the engine. Afterward, put the air cleaner tube into the throttle body.