How to Service and Repair a Blend Door Actuator on 2006 Jeep Wrangler?

You should disable the air bag system on cars with air bags by unattaching and isolating the negative battery cable, then wait a full two minutes so the air bag system capacitor discharges and so there is no danger of accidental air bag deployment. Start by putting the ignition key to the On setting and holding the A/C heater control at mid-temperature for 10 seconds. Remove the negative battery cable and now detach the wire harness from the blend door actuator at the bottom of the HVAC housing, right below the center of the instrument panel. Fix the three screws holding the actuator to the HVAC housing and remove the actuator. To install, put the new blend door actuator in the bottom of the HVAC housing, so that the actuator's output shaft points straight toward the blend door linkage if needed. Place and tighten the three screws on the actuator so that the amount of torque is 2 N.m (17 in. lbs.). Gently connect the two parts of the HVAC wire harness connector to the blend door actuator and screw on the negative battery cable.

OEM 2006 Jeep Wrangler Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Blend Door Actuators found

View related parts
2006 Jeep Wrangler Actuator Part Number: 5073181AA
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Blend Door Actuator; HVAC Heater Blend Door Actuator; Actuator A/C And Heater Panel Door
- Item Weight: 0.70 Pounds
- Item Dimensions: 8.1 x 3.9 x 3.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5073181AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Actuator Part Number: 5073173AA
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; Actuator A/C And Heater Recirculation Door; Actuator A/C And Heater Recirculating
- Item Weight: 0.80 Pounds
- Item Dimensions: 8.3 x 4.1 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5073173AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Floor Duct Part Number: 5066518AA
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; Actuator; A/C and Heater Floor and Defrost Door.
- Item Weight: 0.80 Pounds
- Item Dimensions: 8.2 x 4.2 x 3.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5066518AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Jeep Wrangler Actuator Part Number: 5013741AB
Product Specifications
- Other Name: Actuator - Blend Door; HVAC Defrost Mode Door Actuator; HVAC Heater Blend Door Actuator; Actuator Blend Door
- Item Weight: 1.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5013741AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following 2006 Jeep Wrangler Submodels:
- 65th Anniversary Edition, Rubicon, SE, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.4 L GAS, 6 Cyl 4.0 L GAS

2006 Jeep Wrangler Blend Door Actuator Parts and Q&A

Q: How to Service and Repair a Blend Door Actuator on 2006 Jeep Wrangler?
A: You should disable the air bag system on cars with air bags by unattaching and isolating the negative battery cable, then wait a full two minutes so the air bag system capacitor discharges and so there is no danger of accidental air bag deployment. Start by putting the ignition key to the On setting and holding the A/C heater control at mid-temperature for 10 seconds. Remove the negative battery cable and now detach the wire harness from the blend door actuator at the bottom of the HVAC housing, right below the center of the instrument panel. Fix the three screws holding the actuator to the HVAC housing and remove the actuator. To install, put the new blend door actuator in the bottom of the HVAC housing, so that the actuator's output shaft points straight toward the blend door linkage if needed. Place and tighten the three screws on the actuator so that the amount of torque is 2 N.m (17 in. lbs.). Gently connect the two parts of the HVAC wire harness connector to the blend door actuator and screw on the negative battery cable.