How to Safely Service an Air Bag Sensor on the C-Pillar on 2007 Jeep Commander?

Start by disabling the supplemental restraint system by cutting battery negative cable and letting it sit without power to avoid accidental air bag discharge for two minutes. Take care not to strike or drop the side impact sensor, because damage to it may require calibration or a brand new unit. Place the side impact sensor on the inside of the C-pillar, so the anti-rotation pin on the back fits into the clearance hole. Join the sensor to the mount using the screws and set them to 6.5 Nm (60 in. lbs.). Reconnect the body wire harness connector with the sensor's connector receptacle and put the quarter trim panel back into place on the rear side of the car. Don't reattach the battery negative cable until after you have completed the supplemental restraint system verification test procedure after working on any part of the system.

OEM 2007 Jeep Commander Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Air Bag Sensors found

View related parts
2007 Jeep Commander Impact Sensor, Front Part Number: 4671779AC
$48.02 MSRP: $103.00
You Save: $54.98 (54%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor, Center, Front; Air Bag Sensor; Front Impact Sensor; Side Impact Sensor; Airbag Impact Sensor.
- Position: Front
- Item Weight: 0.50 Pounds
- Item Dimensions: 1.8 x 2.6 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4671779AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Commander Submodels:
- 65th Anniversary Edition, Base, Limited, Overland, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
2007 Jeep Commander Impact Sensor, Front Part Number: 4896173AA
$189.21 MSRP: $279.00
You Save: $89.79 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Impact; Air Bag Impact Sensor, Front; Air Bag Sensor; Front Impact Sensor; Front Sensor; Side Impact Sensor; Sensor Side Airbag Impact; Sensor Impact
- Position: Front
- Item Weight: 0.50 Pounds
- Item Dimensions: 3.7 x 2.6 x 1.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4896173AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
More Info
Fits the following 2007 Jeep Commander Submodels:
- 65th Anniversary Edition, Base, Limited, Overland, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS

2007 Jeep Commander Air Bag Sensor Parts and Q&A

Q: How to Safely Service an Air Bag Sensor on the C-Pillar on 2007 Jeep Commander?
A: Start by disabling the supplemental restraint system by cutting battery negative cable and letting it sit without power to avoid accidental air bag discharge for two minutes. Take care not to strike or drop the side impact sensor, because damage to it may require calibration or a brand new unit. Place the side impact sensor on the inside of the C-pillar, so the anti-rotation pin on the back fits into the clearance hole. Join the sensor to the mount using the screws and set them to 6.5 Nm (60 in. lbs.). Reconnect the body wire harness connector with the sensor's connector receptacle and put the quarter trim panel back into place on the rear side of the car. Don't reattach the battery negative cable until after you have completed the supplemental restraint system verification test procedure after working on any part of the system.