JeepParts
My Garage
My Account
Cart
OEM 2007 Jeep Wrangler A/C Hose
Air Conditioning Hose- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
2 A/C Hoses found
2007 Jeep Wrangler A/C Hoses Part Number: 55056589AB
$99.01 MSRP: $151.00You Save: $51.99 (35%)Product Specifications- Other Name: Line - A/C Discharge; A/C Refrigerant Discharge Hose; A/C Refrigerant Liquid Hose; A/C Hose; Discharge Line; Line A/C Discharge
- Item Weight: 0.80 Pounds
- Item Dimensions: 20.2 x 5.7 x 1.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55056589AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2007 Jeep Wrangler A/C Hoses Part Number: 55056587AC
$200.54 MSRP: $295.00You Save: $94.46 (33%)Product Specifications- Other Name: Line - A/C Suction And Liquid; A/C Refrigerant Suction Hose; A/C Refrigerant Liquid Hose; A/C Hose; Suction Line; Line A/C Suction And Liquid
- Replaces: 55056587AB
- Item Weight: 1.60 Pounds
- Item Dimensions: 3.8 x 6.6 x 40.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 55056587AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
2007 Jeep Wrangler A/C Hose Parts and Q&A
- Q: How to Install an A/C Hose for the Liquid Line on 2007 Jeep Wrangler?A: Before you begin, fit the A/C liquid line in the engine compartment and take off any tape or stops place in the openings of the suction, liquid line fittings, the condenser and expansion valve ports and the fittings at the opening. Apply clean refrigerant oil to new rubber O-ring seals and put them together with a new gasket onto the suction and liquid line fitting sockets, but only use the O-rings and oil that match the R-134a system. Attach the A/C liquid line to the condenser and add the retaining nut, pushing it tight to 23 Nm (17 ft. lbs.). Should you have removed it, set the A/C liquid line into the tapping block connected to the suction line. Air intake from 2.8L equipped vehicles should be fitted onto the throttle body. After that, join the A/C liquid line and A/C suction line to the expansion valve and fasten the retaining nut to 8 Nm (70 in. lbs.). If the situation calls for it, attach the bracket once more to hold the A/C liquid line and suction line. Attach the negative battery cable, take out the refrigerant from the system, set the refrigerant oil amount and charge the refrigerant system.
Related 2007 Jeep Wrangler Parts
2007 Jeep Wrangler Blend Door Actuator
2007 Jeep Wrangler Heater Core
2007 Jeep Wrangler Blower Motor
2007 Jeep Wrangler A/C Compressor
2007 Jeep Wrangler Blower Motor Resistor
2007 Jeep Wrangler Evaporator
2007 Jeep Wrangler A/C Accumulator
2007 Jeep Wrangler A/C Condenser
2007 Jeep Wrangler A/C Expansion Valve
2007 Jeep Wrangler A/C Service Cap
2007 Jeep Wrangler A/C System Valve Core
2007 Jeep Wrangler HVAC Pressure Switch