How to Properly Service and Repair an Exhaust Pipe on Dodge Dakota?

The first thing to do when working on the exhaust pipe is to raise and support the vehicle. Apply Mopar Rust Penetrant to every bolt and nut and let it settle for about 5 minutes. Take out the oxygen sensor, remove the exhaust manifold nuts, free the clamp that holds the exhaust pipe to the converter and pull the pipe out of the converter's front flange before any more actions. Check all components, replace rusted clamps, any broken parts and attach everything, swapping out anything damaged with replacements from the original parts or similar pieces to guarantee the exhaust pipe is level and doesn't make too much sound. Attach the exhaust pipes to the exhaust manifold, using a torque wrench and turning the nuts to 34 Nm (25 ft. lbs.). Join the exhaust pipe to the bottom of the catalytic converter, use the clamp to lock them in place and turn the clamp nuts up to 47 Nm or 35 ft. lbs. of torque. Put back the oxygen sensor connector(s), then drive the car down and see if the engine develops exhaust smoke. Ensure there is no contact between the exhaust and the body panels.

How to Install an Exhaust Pipe on Dodge Dakota?

Removing any burrs from the exhaust pipe (2) is necessary before you install it. Attach the exhaust pipe (2) to the muffler (4) and be sure the alignment tang is in the proper slot. At this point, just put on the muffler-to-exhaust pipe clamp, but do not tighten it yet. If the rear muffler insulator (5) was removed, put it back on now and then slide on the tail pipe insulators (1). Look along the exhaust system to see if it has touched the body panels and correct it if needed. After installation, use an air wrench to tighten the muffler-to-exhaust pipe clamp to 61 Nm (45 ft. lbs.), drive the car to the ground and check for exhaust leaks, fixing those found. Remember that the band clamps should be changed after you have removed them.

OEM Dodge Dakota Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

59 Exhaust Pipes found

View related parts
Dodge Dakota Muffler Part Number: 52103676AC
$106.34 MSRP: $204.00
You Save: $97.66 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Muffler - Exhaust; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Muffler Exhaust
- Replaces: 52103676AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Dakota | Base, SLT, SLT Plus, SXT, Sport, Sport Plus | 6 Cyl 3.7 L GAS
View related parts
Dodge Dakota Tail Pipe Part Number: 52103251AC
$24.77 MSRP: $143.00
You Save: $118.23 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Tail Pipe; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Tailpipe
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2003 Dodge Dakota | Base, SLT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Extension Pipe, Center Part Number: 52103121
$5.25 MSRP: $6.65
You Save: $1.40 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Exhaust; Exhaust Intermediate Pipe, Center; Exhaust Pipe; Intermed Pipe
- Position: Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Dakota | Base, R/T, SLT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Extension Pipe, Center Part Number: 52103120
Product Specifications
- Other Name: Pipe Exhaust; Exhaust Intermediate Pipe, Center; Exhaust Pipe; Intermed Pipe
- Position: Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Dakota | Base, R/T, SLT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52103247AB
Product Specifications
- Other Name: Muffler - Exhaust; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Resonator
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2003 Dodge Dakota | Base, SLT, SXT, Sport | 6 Cyl 3.9 L GAS
View related parts
Dodge Dakota Catalytic Converter Part Number: 52103480AE
Product Specifications
- Other Name: Converter - Catalytic; Converter; Converter Catalytic
- Replaces: 52103480AD, 52103480AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Dodge Dakota | Base, SLT, SXT, Sport | 6 Cyl 3.9 L GAS
View related parts
Dodge Dakota Front Pipe Part Number: 52013634AA
Product Specifications
- Other Name: Resonator - Exhaust; Exhaust Pipe; Extension Pipe; Pipe And Resonator Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Dakota | Laramie, SLT, ST, Sport | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Dakota Front Pipe Part Number: 52019303
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Pipe
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996 Dodge Dakota | Base, SLT, Sport, WS | 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Front Pipe Part Number: 52020079AB
Product Specifications
- Other Name: Pipe; Exhaust Intermediate Pipe, Front; Exhaust Pipe; Pipe Exhaust
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-2000 Dodge Dakota | Base, SLT, Sport | 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52021141
Product Specifications
- Other Name: Exhaust Muffler; Resonator; Muffler Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Dakota | Base, SLT, Sport | 8 Cyl 5.2 L GAS
View related parts
Dodge Dakota Front Pipe Part Number: 52021743AC
Product Specifications
- Other Name: Pipe - Exhaust Extension; Exhaust Intermediate Pipe, Front; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Extension Pipe
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Dakota | Base, SLT, SLT Plus, SXT, Sport, Sport Plus | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS
View related parts
Dodge Dakota Front Pipe Part Number: 52021744AC
Product Specifications
- Other Name: Pipe - Exhaust Extension; Exhaust Intermediate Pipe, Front; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Extension Pipe
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Dodge Dakota | Base, SLT, SLT Plus, SXT, Sport, Sport Plus | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52022122AB
Product Specifications
- Other Name: Exhaust Muffler; Resonator; Muffler Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2002 Dodge Dakota | Base, SLT, Sport | 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Extension Pipe, Center Part Number: 52103010
Product Specifications
- Other Name: Pipe Exhaust; Exhaust Intermediate Pipe, Center; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Intermed Pipe
- Position: Center
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Dakota | Base, R/T, SLT, Sport | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52103161
Product Specifications
- Other Name: Muffler Exhaust; Exhaust Muffler; Resonator
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Dodge Dakota | R/T | 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Extension Pipe Part Number: 52103213AA
Product Specifications
- Other Name: Pipe Exhaust; Exhaust Intermediate Pipe; Exhaust Pipe; Intermed Pipe
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Dodge Dakota | Base, SLT, Sport | 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52103249AB
Product Specifications
- Other Name: Muffler - Exhaust; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Resonator; Muffler Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2003 Dodge Dakota | Base, SLT, Sport | 6 Cyl 3.9 L GAS
View related parts
Dodge Dakota Converter & Pipe Part Number: 52103269AA
Product Specifications
- Other Name: Converter Catalytic; Catalytic Converter; Exhaust Pipe
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999 Dodge Dakota | Base, SLT, Sport | 4 Cyl 2.5 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52103270AB
Product Specifications
- Other Name: Muffler - Exhaust; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Resonator; Muffler Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2003 Dodge Dakota | Base, SLT, Sport | 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Dakota Muffler Part Number: 52103676AD
Product Specifications
- Other Name: Muffler - Exhaust; Exhaust Muffler; Resonator; Muffler Exhaust
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Dodge Dakota | Laramie, SLT, ST, Sport | 6 Cyl 3.7 L GAS

| Page 1 of 3 |Next >

1-20 of 59 Results

Dodge Dakota Exhaust Pipe

Choose OEM Exhaust Pipe that meet Dodge factory standards. Dodge designs and tests every component for precision and durability. Each Exhaust Pipe follows strict manufacturing steps to lock in quality and fit. If your Dodge Dakota matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Dakota parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

The Dodge Dakota Exhaust Pipe is one of the major parts that are very vital and have a very sensitive job to do in the car. Studying the exhaust pipe, one will notice that one of the primary objectives is to effectively expel toxic gases from the engine and prevent them from getting into the cabin and endangering the lives of passengers. Since this is a Dodge Dakota Exhaust Pipe, it should fit a number of Dakota models to suit the need of any car owner intending to preserve the integrity of his or her car. Heavy-duty built that is designed to stand physical and mechanical stresses common with use makes the Dakota reliable and solid on the roads. Exhaust pipe meets other sections of the exhaust system, for instance the muffler and catalytic convert, that helps in an efficient working of the Dakota. In the same way, the Dodge Dakota Exhaust Pipe also serves as a noise and vibration suppressor hence improving the vehicular steadiness. One unique technique that has been used in this exhaust pipe is the reduced chances of rust as well as wear which is crucial in this area for durability particularly in rigorous use of the vehicle. Thus, preserving the exhaust system, the Dodge Dakota Exhaust Pipe is not simply improving the vehicle's performance, but contributing to safety as well. In sum, the Dodge Dakota Exhaust Pipe is one more proof of the brand's adherence to producing high-quality automotive parts that will provide the needed performance to the Dakota vehicle owners who value reliability and practicality in their vehicles.

Dodge Dakota Exhaust Pipe Parts and Q&A

Tail Pipe
52103251AC
Q: How to Properly Service and Repair an Exhaust Pipe on Dodge Dakota?
A:
The first thing to do when working on the exhaust pipe is to raise and support the vehicle. Apply Mopar Rust Penetrant to every bolt and nut and let it settle for about 5 minutes. Take out the Oxygen Sensor, remove the Exhaust Manifold nuts, free the clamp that holds the exhaust pipe to the converter and pull the pipe out of the converter's front flange before any more actions. Check all components, replace rusted clamps, any broken parts and attach everything, swapping out anything damaged with replacements from the original parts or similar pieces to guarantee the exhaust pipe is level and doesn't make too much sound. Attach the exhaust pipes to the exhaust manifold, using a torque wrench and turning the nuts to 34 Nm (25 ft. lbs.). Join the exhaust pipe to the bottom of the catalytic converter, use the clamp to lock them in place and turn the clamp nuts up to 47 Nm or 35 ft. lbs. of torque. Put back the oxygen sensor connector(s), then drive the car down and see if the engine develops exhaust smoke. Ensure there is no contact between the exhaust and the body panels.
Tail Pipe
52855886AA
Q: How to Install an Exhaust Pipe on Dodge Dakota?
A:
Removing any burrs from the exhaust pipe (2) is necessary before you install it. Attach the exhaust pipe (2) to the Muffler (4) and be sure the alignment tang is in the proper slot. At this point, just put on the muffler-to-exhaust pipe clamp, but do not tighten it yet. If the rear muffler insulator (5) was removed, put it back on now and then slide on the tail pipe insulators (1). Look along the exhaust system to see if it has touched the body panels and correct it if needed. After installation, use an air wrench to tighten the muffler-to-exhaust pipe clamp to 61 Nm (45 ft. lbs.), drive the car to the ground and check for exhaust leaks, fixing those found. Remember that the band clamps should be changed after you have removed them.