How to Install a Wiper Switch with Airbags on Dodge Dakota?

First, to remove the bag, unhook and leave unconnected the car battery's negative cable and wait a full two minutes to allow the air bag capacitor to discharge. Take the multi-function switch and fit it into the mounting housing from the left side, so the alignment pins connect. Turn the steering wheel as needed to place and tighten both screws at the back of the switch to the mounting housing to 2 Nm (20 in. lbs.). Attach the wire harness connector again to the back of the switch, slide the shroud onto the bottom part of the steering column and tighten the center screw to 2 Nm (20 in. lbs). Put the upper shroud on top of the lower shroud, engaging the gearshift lever gap hider if the car is an automatic. Match the upper shroud's snaps with the slot-shaped holes in the lower shroud and squeeze it together by hand before tightening the two outboard screws to 2 Nm (20 in. lbs.). Slide the tilt steering column knob onto the device and tighten it with a screw set to 2 Nm (20 in. lbs.). Link the vehicle's battery negative cable back in place.

How to Service and Repair a Wiper Switch Safely on Dodge Durango?

When you have a car with air bags, take steps to avoid accidentally setting off the air bag. If necessary, unfasten the tilt steering column lever, next take off both upper and lower steering shrouds and then unbolt the bottom fixed column shroud. Turn the upper fixed column shroud around so it is behind the switch and then open the tamper proof screws using a Snap On tamper proof torx bit TTXR2OB2 or something similar. Pull the switch ever so slightly from the steering column to get at the screw on the multi-function switch wire harness connector, then disconnect the wire harness from the switch. When installing, use the same steps as for removal, but firm the multi-function switch wire harness connector screw to 2 Nm (17 in. lbs.) and make sure the multi-function switch mounting screws are 2 Nm (17 in. lbs.) tightly fastened. Disconnect and set aside the negative cable of the battery and remove the lower bezel from the instrument panel for the rear wiper switch. After that, take out the two screws holding the rear window switch pod to the instrument panel lower bezel and detach the pod. Install the exhaust manifold in reverse order and tighten every screw to 2.2 Nm or 20 in. lbs.

OEM Dodge Wiper Switch

Windshield Wiper Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

44 Wiper Switches found

View related parts
Dodge Multifunction Switch Part Number: 4760594AC
$138.08 MSRP: $251.00
You Save: $112.92 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Combination Switch; Multi Purpose Switch; Switch Multifunction
Fits the following Dodge Models:
- Intrepid | 1998-2004 | Base, ES, Police, R/T, SE, SXT | 6 Cyl 2.7 L GAS, 6 Cyl 3.2 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Headlamp Switch Part Number: 5066185AA
$112.34 MSRP: $150.00
You Save: $37.66 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Combination Switch; Multi Purpose Switch; Switch Multifunction
Fits the following Dodge Models:
- Viper | 2008-2010, 2003-2006 | SRT-10, SRT-10 ACR | 10 Cyl 8.3 L GAS, 10 Cyl 8.4 L GAS
View related parts
Dodge Multifunction Switch Part Number: 4760437AB
$110.71 MSRP: $159.00
You Save: $48.29 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Signal Switch; Switch Multifunction
Fits the following Dodge Models:
- Intrepid | 1995-1997 | Base, ES | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Multifunction Switch Part Number: 4608603AN
$226.18 MSRP: $299.00
You Save: $72.82 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Combination Switch; Multi Purpose Switch
- Replaces: 4608603AO, 4608603AM, 4608603AH, 4608603AE, 4608603AG, 4608603AF, 4608603AJ, 4608603AI
Fits the following Dodge Models:
- Stratus | 2001-2006 | ES, R/T, SE, SE Plus, SXT | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Multifunction Switch Part Number: 56045078AD
$184.09 MSRP: $233.36
You Save: $49.27 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Windshield Washer Switch.; Wiper Switch; Switch Multifunction
Fits the following Dodge Models:
- Dakota | 2001-2004 | Base, R/T, SLT, SLT Plus, SXT, Sport, Sport Plus | 4 Cyl 2.5 L GAS, 6 Cyl 3.7 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
- Durango | 2001-2003 | Base, R/T, SLT, SLT Plus, SXT, Sport | 8 Cyl 4.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Multifunction Switch Part Number: 68024198AD
$21.20 MSRP: $67.20
You Save: $46.00 (69%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Multifunction; Switch Multifunction
- Replaces: 68024198AC, 68024198AB
Fits the following Dodge Models:
- Avenger | 2008-2009 | R/T, SE, SXT | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Dodge Wiper Switch Part Number: MR558804
$99.09 MSRP: $125.61
You Save: $26.52 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch - Windshield Wiper; Windshield Wiper Switch; Windshield Washer Switch; Switch Windshield Wiper
Fits the following Dodge Models:
- Stratus | 2001-2005 | R/T, SE, SXT | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Dodge Switch Assembly Part Number: 4373304
$17.28 MSRP: $21.90
You Save: $4.62 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Switch Pod Assembly Instrument Panel Right; Multi Purpose Switch; Rear Wiper Switch; Switch, Windshield Wiper & Washer; Windshield Wiper, Front & Rear
Fits the following Dodge Models:
- Caravan | 1991 | Base, C/V, ES, LE, SE | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Grand Caravan | 1991 | LE, SE | 6 Cyl 3.3 L GAS
View related parts
Dodge Wiper Switch Part Number: 56007299
Product Specifications
- Other Name: Switch Assembly - Windshield Wiper/Washer - Intermittent; Windshield Washer Switch; Switch; Switch, Multi - Function Turn Signal & Wiper; Switch Assembly, Wipers
Fits the following Dodge Models:
- Viper | 1992-1996 | Base, GTS | 10 Cyl 8.0 L GAS
View related parts
Dodge Multifunction Switch Part Number: 4608383
Product Specifications
- Other Name: Switch - Multifunction; Windshield Washer Switch; Multi Purpose Switch; Headlamp Switch; Combination Switch; Wiper Switch; Multifunction Switch W/O Fog Lamp
- Replaces: 4608383AB
Fits the following Dodge Models:
- Stratus | 1995-2000 | Base, ES, SE | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Dodge Turn Signal Switch Part Number: 5183950AF
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Combination Switch; Multi Purpose Switch; Multifunction Switch; Signal Switch; Switch Multifunction
- Replaces: 5183950AE, 5183950AD, 5183950AC, 5183950AB, 5183950AA
Fits the following Dodge Models:
- Avenger | 2007-2011 | Express, Heat, Lux, Mainstreet, R/T, SE, SXT | 2.4L L4, 2.7L V6, 3.5L V6, 3.6L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX
- Caliber | 2009-2012 | 1.8L L4, 2.0L L4, 2.4L L4
- Journey | 2009-2010 | Base, Crew, R/T, SE, SXT | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS
- Nitro | 2007-2010 | R/T, SE, SLT, SXT | 3.7L V6, 4.0L V6, 6 Cyl 3.7 L GAS, 6 Cyl 4.0 L GAS
View More
View related parts
Dodge Wiper Switch Part Number: 4661942
Product Specifications
- Other Name: Switch, Wipers; Windshield Washer Switch; Front Wiper Switch; Switch, Wiper Control W/2 Speed Wipers; Switch Windshield Wiper; Switch, Wiper Control
Fits the following Dodge Models:
- Neon | 1995-1999 | ACR, Base, High Line, R/T, Sport | 4 Cyl 2.0 L GAS
View related parts
Dodge Multifunction Switch Part Number: 4685586
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Combination Switch; Switch Multifunction
Fits the following Dodge Models:
- Caravan | 1998-2000 | Base, ES, LE, SE, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, BATTERY EV (EV/BEV)
- Grand Caravan | 1998-2000 | Base, ES, LE, SE, Sport | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Dodge Multifunction Switch Part Number: 5012382AA
Product Specifications
- Other Name: Switch - Multifunction; Multi Purpose Switch; Combination Switch; Switch Multifunction
Fits the following Dodge Models:
- Caravan | 1996-1997 | Base, ES, LE, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, BATTERY EV (EV/BEV)
- Grand Caravan | 1996-1997 | Base, ES, LE, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L CNG, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Dodge Turn Signal Switch Part Number: 56049823AB
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Switch; Air Bag Clockspring.; Multifunction Switch; Switch Housing; Ignition Housing; Clockspring; Switch Multifunction
- Replaces: 56045515AA, 56049823AA, 56045165AB
Fits the following Dodge Models:
- Dakota | 2001-2010 | Big Horn, Laramie, Lone Star, SLT, ST, SXT, Sport, TRX, TRX4 | 2.5L L4, 3.7L V6, 3.9L V6, 4.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
- Durango | 2001-2008 | Adventurer, Limited, SLT, ST, SXT | 3.7L V6, 4.7L V8, 5.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
- Ram 1500 | 2002-2008 | Laramie, SLT, SRT-10, ST, SXT, Sport, TRX4 | 10 Cyl 8.3 L GAS, 3.7L V6, 4.7L V8, 5.7L V8, 5.9L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS, 8.3L V10
- Ram 2500 | 2003-2009 | Laramie, Power Wagon, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS, 8.0L V10
- Ram 3500 | 2003-2010 | Laramie, SLT, ST, SXT, Sport, TRX4 | 10 Cyl 8.0 L GAS, 5.7L V8, 5.9L L6, 6 Cyl 5.9 L DIESEL, 6 Cyl 6.7 L DIESEL, 6.7L L6, 8 Cyl 5.7 L GAS, 8.0L V10
- Ram 4500 | 2008-2010 | 6.7L L6
- Ram 5500 | 2008-2010 | 6.7L L6
- Ram Van | 2001-2003 | 3.9L V6, 5.2L V8, 5.9L V8
- Ram Wagon | 2001-2002 | 3.9L V6, 5.2L V8, 5.9L V8
View More
View related parts
Dodge Ignition Switch Part Number: 4728424
Product Specifications
- Other Name: Switch - Multifunction; Turn Signal & Combination Lever; Steering Column Housing; Windshield Washer Switch.; Turn Signal Switch; Multifunction, Wiper, Headlamp Dimmer, Hazard, Signal & Tilt options.
Fits the following Dodge Models:
- B150 | 1991-1994 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B1500 | 1995-1998 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B250 | 1991-1994 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B2500 | 1995-1998 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B350 | 1991-1994 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B3500 | 1995-1998 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1991-1993 | Base, S | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1991-1993 | Base | 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1991-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Dakota | 1991-2000 | Base, LE, R/T, S, SE, SLT, Sport, WS | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View More
View related parts
Dodge Rear Wiper Switch Part Number: MB604781
Product Specifications
- Other Name: Switch - Windshield Wiper; Switch, Rear Wiper & Wash
Fits the following Dodge Models:
- Stealth | 1991-1996 | Base, ES, R/T, R/T Turbo | 6 Cyl 3.0 L GAS
View related parts
Dodge Wiper Lever Part Number: MB852131
Product Specifications
- Other Name: Switch - Windshield Wiper & Windshield; Front Wiper Switch; Switch, Wiper & Washer
Fits the following Dodge Models:
- Stealth | 1991-1996 | Base, ES, R/T, R/T Turbo | 6 Cyl 3.0 L GAS
View related parts
Dodge Turn Signal Switch Part Number: 4778760
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Multi Purpose Switch; Combination Switch; Multi-Function Turn Signal & Wiper; Headlamp Dimmer; Signal & Hazard Switch.
Fits the following Dodge Models:
- B150 | 1991-1994 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B1500 | 1995-1997 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS
- B250 | 1991-1994 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B2500 | 1995-1997 | Base | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B350 | 1991-1994 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- B3500 | 1995-1997 | Base | 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D150 | 1991-1993 | Base, S | 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D250 | 1991-1993 | Base | 6 Cyl 3.9 L GAS, 6 Cyl 5.9 L DIESEL, 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
- D350 | 1991-1993 | Base | 6 Cyl 5.9 L DIESEL, 8 Cyl 5.9 L GAS
- Dakota | 1991-1997 | Base, LE, S, SE, SLT, Sport, WS | 4 Cyl 2.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.2 L CNG, 8 Cyl 5.2 L GAS
View More
View related parts
Dodge Multifunction Switch Part Number: 4608808AF
Product Specifications
- Other Name: Switch - Multifunction; Steering Column Switch Housing; Combination Switch; Multi Purpose Switch
- Replaces: 4608808AE, 4608808AD, 4608808AG
Fits the following Dodge Models:
- Stratus | 2004-2006 | ES, R/T, SE, SXT | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS

| Page 1 of 3 |Next >

1-20 of 44 Results

Dodge Wiper Switch

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Wiper Switch for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Wiper Switch allows one to stay in focus by firing the blades as they twist their fingertips. Over a hundred years of Dodge running out of a dirty machine shop to a badge screaming of power. Rolled the first all-steel body in 1914, it filled the streets with HEMI power, pumped out Viper adrenaline, and now piped their 600-watt Fratzonic roar into a silent electric air, demonstrating that raw muscle could be refined without losing its attitude. The Wiper Switch name comes along as one more sign that the brand has never sought timid solutions to problems, celebrates burnouts, desert runs, and commutes with equal Dodge Wiper Switch springs to action every time it gets raining and Dodge Wiper Switch directs its simple stalk inputs into exact motor signals to sweep the glass clean and it has survived years of vibration, heat, and slush, so it has no complaints. Every column is furnished within with Dodge Wiper Switch with established contacts and tight tolerances providing sharp detents so that one flick provides intermittent rhythm and a solid push provides full blast, and since the circuitry is not exposed to moisture, the component maintains its own voltage level, protecting fuses, bulbs, and even visibility itself over miles of unpredictable weather.

Dodge Wiper Switch Parts and Q&A

Turn Signal Switch
56049823AB
Q: How to Install a Wiper Switch with Airbags on Dodge Dakota?
A:
First, to remove the bag, unhook and leave unconnected the car battery's negative cable and wait a full two minutes to allow the air bag capacitor to discharge. Take the multi-function switch and fit it into the mounting housing from the left side, so the alignment pins connect. Turn the steering wheel as needed to place and tighten both screws at the back of the switch to the mounting housing to 2 Nm (20 in. lbs.). Attach the wire harness connector again to the back of the switch, slide the shroud onto the bottom part of the steering column and tighten the center screw to 2 Nm (20 in. lbs). Put the upper shroud on top of the lower shroud, engaging the gearshift lever gap hider if the car is an automatic. Match the upper shroud's snaps with the slot-shaped holes in the lower shroud and squeeze it together by hand before tightening the two outboard screws to 2 Nm (20 in. lbs.). Slide the tilt steering column knob onto the device and tighten it with a screw set to 2 Nm (20 in. lbs.). Link the vehicle's battery negative cable back in place.
Ignition Switch
4728424
Q: How to Service and Repair a Wiper Switch Safely on Dodge Durango?
A:
When you have a car with air bags, take steps to avoid accidentally setting off the air bag. If necessary, unfasten the tilt steering column lever, next take off both upper and lower steering shrouds and then unbolt the bottom fixed column shroud. Turn the upper fixed column shroud around so it is behind the switch and then open the tamper proof screws using a Snap On tamper proof torx bit TTXR2OB2 or something similar. Pull the switch ever so slightly from the steering column to get at the screw on the multi-function switch wire harness connector, then disconnect the wire harness from the switch. When installing, use the same steps as for removal, but firm the multi-function switch wire harness connector screw to 2 Nm (17 in. lbs.) and make sure the multi-function switch mounting screws are 2 Nm (17 in. lbs.) tightly fastened. Disconnect and set aside the negative cable of the battery and remove the lower bezel from the instrument panel for the rear wiper switch. After that, take out the two screws holding the rear window switch pod to the instrument panel lower bezel and detach the pod. Install the exhaust manifold in reverse order and tighten every screw to 2.2 Nm or 20 in. lbs.