How to Maintain a Throttle Cable and Its Linkage on Jeep Grand Cherokee?

Start the throttle cable and linkage service by tugging on the accelerator pedal inside the vehicle and taking out the plastic retainer and the core wire that holds the cable. Following this, take off the cable core from the pedal arm and unclip the cable on the dash panel. Pull the metal housing into the engine section and unclip the cable that is on the valve cover. Disconnect the cable at the throttle body bellcrank ball by snapping it backward, then squeeze the release tabs to remove the cable from the bracket and take it inside the vehicle. Connect the cable ball to the throttle body bellcrank ball and slide the throttle cable up into the hole of the bracket until the release tabs lock in place. Hook the cable into its clips on the engine valve cover, move the rubber grommet back from the cable sheath and then place it into the dashboard panel until it snaps into place. Raise the cable up through the hole in the dash panel by pushing the cable housing into the grommet and install the clip holding it from within the car. Insert the cable core wire into the hole at the pedal end and push the clip inside so it snaps in. Take a moment to use the accelerator pedal, verifying there is no resistance, before starting the system.

How to Maintain and Fix a Throttle Cable on Jeep Wrangler?

Begin by opening the car door, stepping inside, positioned on the pedal and simply removing the plastic retainer and wire from the upper end of the pedal arm. Once done, pull out the outer wire from the pedal arm area. Slightly squeeze the tabs on either side of the cable housing at the dash panel to remove the assembly and move it into the engine compartment. Next, take out the cable from the clip guides on the top of the engine cylinder head. To unhook the throttle cable ball from the pin, slide the ball toward the rear and squeeze the edges of the release tabs to remove the cable from the bracket. Once the old throttle cable is removed, put the new cable through the hole in the throttle body bracket, slide the retainer tabs into place until they are locked and attach the cable ball end to the other end of the linkage. Slide the cable clip over the cable and attach it to the cover on the engine cylinder head. Then pass the other part of the cable through the dash opening and have its retaining tabs lock into the panel. Make sure the index tab matches its opening inside the accelerator pedal arm by slowly sliding the wire into the slot at the top. Rotate the cable retainer up until it snaps onto the index tab that's located inside the pedal arm opening. Before you start your car, push the accelerator lightly to make sure there is no binding.

OEM Jeep Throttle Cable

Accelerator Throttle Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Throttle Cables found

View related parts
Jeep Throttle Cable Part Number: 52079382
$119.98 MSRP: $152.10
You Save: $32.12 (22%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable - Accelerator Control
Fits the following Jeep Models:
- Cherokee | 1992-1995 | Base, Briarwood, Country, Laredo, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
- Comanche | 1992 | Base, Eliminator, Pioneer | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Throttle Cable Part Number: 4854150AB
$30.44 MSRP: $44.80
You Save: $14.36 (33%)
ADD TO CART
Product Specifications
- Other Name: Cable - Accelerator; Cable Accelerator
Fits the following Jeep Models:
- Grand Cherokee | 1999-2004 | Laredo, Limited, Special Edition, Sport | 6 Cyl 4.0 L GAS
View related parts
Jeep Throttle Cable Part Number: 53013210AA
Product Specifications
- Other Name: Cable - Accelerator
Fits the following Jeep Models:
- Grand Cherokee | 1997-1998 | 5.9 Limited, Laredo, Limited, Orvis, TSi | 8 Cyl 5.2 L GAS, 8 Cyl 5.9 L GAS
View related parts
Jeep Throttle Cable Part Number: 53013136AG
Product Specifications
- Other Name: Cable - Accelerator; Cruise Control Cable; Cable
- Replaces: 53013136AD, 53013136AE, 53013136AC, 53013136AF
Fits the following Jeep Models:
- Liberty | 2002-2007 | 65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Jeep Throttle Cable Part Number: 52104352AA
Product Specifications
- Other Name: Cable - Throttle Valve; Cable Throttle Valve
Fits the following Jeep Models:
- Grand Cherokee | 1994-1996 | Laredo, Limited, Orvis, SE | 6 Cyl 4.0 L GAS
View related parts
Jeep Throttle Cable Part Number: 52077578
Product Specifications
- Other Name: Cable - Throttle Control; Cable, Throttle Control; Cable Throttle Control; Cable, Throttle
Fits the following Jeep Models:
- Cherokee | 1996-2001 | Classic, Country, Limited, SE, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Throttle Cable Part Number: 53013137AB
Product Specifications
- Other Name: Cable - Accelerator; Cruise Control Cable; Cable; Cable Accelerator
Fits the following Jeep Models:
- Liberty | 2002-2005 | Sport | 4 Cyl 2.4 L GAS
View related parts
Jeep Throttle Cable Part Number: 52109501AB
Product Specifications
- Other Name: Cable - Accelerator; Cable Accelerator
Fits the following Jeep Models:
- Wrangler | 2003-2006 | SE | 4 Cyl 2.4 L GAS
View related parts
Jeep Throttle Cable Part Number: 52078171AB
Product Specifications
- Other Name: Cable - Throttle Valve; Cable Throttle Valve
Fits the following Jeep Models:
- Cherokee | 1996 | SE | 4 Cyl 2.5 L GAS
View related parts
Jeep Throttle Cable Part Number: 4854137
Product Specifications
- Other Name: Cable - Accelerator; Cable Accelerator
Fits the following Jeep Models:
- Wrangler | 1997-2006 | 65th Anniversary Edition, Rubicon, SE, Sahara, Sport, Unlimited, Unlimited Rubicon, X | 4 Cyl 2.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Jeep Throttle Cable Part Number: 4854061
Product Specifications
- Other Name: Cable; Cable Accelerator
Fits the following Jeep Models:
- Grand Cherokee | 1999-2000 | Laredo, Limited | 8 Cyl 4.7 L GAS
View related parts
Jeep Throttle Cable Part Number: 52079204
$79.08 MSRP: $119.00
You Save: $39.92 (34%)
Product Specifications
- Other Name: Cable - Throttle Valve; Cable, Throttle Valve Kickdown Control, W/Automatic Transmission; Cable Throttle Valve
Fits the following Jeep Models:
- Grand Cherokee | 1994-1996 | Laredo, Limited, Orvis, SE | 8 Cyl 5.2 L GAS
View related parts
Jeep Throttle Cable Part Number: 52109653AE
Product Specifications
- Other Name: Cable - Accelerator; Cruise Control Cable; Cable; Cable Accelerator
- Replaces: 52109653AD
Fits the following Jeep Models:
- Commander | 2006-2007 | 65th Anniversary Edition, Base, Limited, Overland, Sport | 3.7L V6, 4.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
- Grand Cherokee | 2005-2007 | 65th Anniversary Edition, Laredo, Limited, Overland, SRT8 | 3.7L V6, 4.7L V8, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.1 L GAS
View related parts
Jeep Throttle Cable Part Number: 52078800
Product Specifications
- Other Name: Cable - Assembly - Accelerator Control; Cable, Accelerator Control
Fits the following Jeep Models:
- Grand Cherokee | 1993 | Base, Laredo, Limited | 8 Cyl 5.2 L GAS
View related parts
Jeep Throttle Cable Part Number: 4854061AD
Product Specifications
- Other Name: Cable - Accelerator; Cable Accelerator
- Replaces: 4854061AC
Fits the following Jeep Models:
- Grand Cherokee | 2001-2004 | Laredo, Limited, Overland, Special Edition, Sport | 8 Cyl 4.7 L GAS
View related parts
Jeep Throttle Cable Part Number: 52851243AC
Product Specifications
- Other Name: Cable - Accelerator; Cable Accelerator
Fits the following Jeep Models:
- Liberty | 2005 | Limited, Sport | 4 Cyl 2.8 L DIESEL

Jeep Throttle Cable

OEM parts sourced directly from Jeep deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Jeep Throttle Cable for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Jeep Throttle Cable joins your right foot to the engine and immediately gives you grunt whenever you need it. Jeep created its legend on the rough wartime roads and rolled right into the home driveways without losing any biting. Jeep retains that rugged advantage with intelligent gratuities such as Selec-Terrain, voice recognition and on-air adjustments. Jeepers share trail tales, wrench on the weekend, and lean on an international fraternity that places greater emphasis on the dirt than on the polish. All Jeep rigs are covered with square lines, open skies, and have enough ground clearance to scoff at worn-out tracks. The axles are rock-prepared, the skid plates are in place and that familiar seven-slot grille is screaming purpose, not glamour. The rigs are reliable to drivers as they are able to withstand snow, sand and mud. Throttle Cable remains no more complicated but important, and it features a steel core contained within a hard material sheath, between the pedal and throttle body. Throttle Cable ensures a clean airflow to the engine to such an extent that the engine starts once you lift the pedal regardless of the rise in altitude. The strands are corrosion resistant and have a tight tolerance which makes Throttle Cable shake off mud, heat and vibration, maintaining the response sharp after many years. Throttle Cable also provides good mechanical feedback allowing the drivers to experience the exact amount of power they request by electronic throttles which are diluted.

Jeep Throttle Cable Parts and Q&A

Throttle Cable
4854150AB
Q: How to Maintain a Throttle Cable and Its Linkage on Jeep Grand Cherokee?
A:
Start the throttle cable and linkage service by tugging on the accelerator pedal inside the vehicle and taking out the plastic retainer and the core wire that holds the cable. Following this, take off the cable core from the pedal arm and unclip the cable on the dash panel. Pull the metal housing into the engine section and unclip the cable that is on the valve cover. Disconnect the cable at the throttle body bellcrank ball by snapping it backward, then squeeze the release tabs to remove the cable from the bracket and take it inside the vehicle. Connect the cable ball to the throttle body bellcrank ball and slide the throttle cable up into the hole of the bracket until the release tabs lock in place. Hook the cable into its clips on the engine valve cover, move the rubber grommet back from the cable sheath and then place it into the dashboard panel until it snaps into place. Raise the cable up through the hole in the dash panel by pushing the cable housing into the grommet and install the clip holding it from within the car. Insert the cable core wire into the hole at the pedal end and push the clip inside so it snaps in. Take a moment to use the accelerator pedal, verifying there is no resistance, before starting the system.
Throttle Cable
4854137
Q: How to Maintain and Fix a Throttle Cable on Jeep Wrangler?
A:
Begin by opening the car door, stepping inside, positioned on the pedal and simply removing the plastic retainer and wire from the upper end of the pedal arm. Once done, pull out the outer wire from the pedal arm area. Slightly squeeze the tabs on either side of the cable housing at the dash panel to remove the assembly and move it into the engine compartment. Next, take out the cable from the clip guides on the top of the engine cylinder head. To unhook the throttle cable ball from the pin, slide the ball toward the rear and squeeze the edges of the release tabs to remove the cable from the bracket. Once the old throttle cable is removed, put the new cable through the hole in the throttle body bracket, slide the retainer tabs into place until they are locked and attach the cable ball end to the other end of the linkage. Slide the cable clip over the cable and attach it to the cover on the engine cylinder head. Then pass the other part of the cable through the dash opening and have its retaining tabs lock into the panel. Make sure the index tab matches its opening inside the accelerator pedal arm by slowly sliding the wire into the slot at the top. Rotate the cable retainer up until it snaps onto the index tab that's located inside the pedal arm opening. Before you start your car, push the accelerator lightly to make sure there is no binding.