How to Service the Rear Brake Disc on Chrysler Pacifica?

Raise and support your vehicle, then take the tire and wheel assembly off. Before removing the caliper, you may need to slightly stiff the caliper with the piston, working gently so pressure doesn't damage it. After that, take out the two caliper guide pin bolts and lift the caliper assembly up and away from the upper adapter abutment by turning the caliper bottom away from the brake disc. Hanging the caliper with wire or cord from the vehicle will prevent damage to the brake hose. Remove the clips attaching the brake disc to the wheel mounting studs and take it off the hub. Before putting in the brakes, look over the disc and parking brake shoes and then clean off any debris or corrosion on the hub face. Put the new brake disc in place on the wheel mounting studs of the hub, checking that all abutment shims are set on the caliper adapter's slide abutments. Be careful not to harm the guide pin bushings and sleeves when mounting the caliper assembly by pulling back the caliper guide pins to avoid contact with the mounting bosses. Placement has the caliper and brake shoes over top the brake disc, aligning the high end of the outside shoe with the caliper slide groove and fit and set the bottom of the caliper on the adapter on your car. Make sure to install the caliper guide pin bolts with care so they don't become cross-threaded and tighten them to 23 Nm (200 inch-lbs.). Place the wheel and tire assembly in its proper place, adjusting the nuts to 135 Nm (100 ft. lbs.) before relaxing the lowering stand for the car. First, brake several times while the car is parked to overcome air gaps and to confirm a good brake response, monitor and maintain the brake fluid and finally drive the car slowly a few times to get brakes working properly.

How to Remove and Replace a Front Brake Disc on Chrysler Pacifica?

Before taking off or changing the front brake rotor/disc, you need to raise and secure the vehicle. Following that, undo the mounting nuts and pull out the tire and wheel from the car. At times, you may need to pull the caliper pistons back just a small amount so the shoes are farther from the rotor and caliper can be easily removed from the knuckle; this can often be done by holding the caliper at its rear and pulling away while still using the guide pins, making sure not to touch the piston to keep it safe. After that, unscrew the two bolts that hold the disc brake caliper adapter to the knuckle. Remove the disc brake caliper and adapter as one part from the knuckle, then hang it clear of other work using wire or a bungee cord so the hose isn't stretched. After that, take off any clips locking the brake rotor to the wheel studs and remove the brake rotor from the hub and bearing.

OEM Chrysler Pacifica Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Brake Discs found

View related parts
Chrysler Pacifica Rotor, Front Part Number: 4779712AB
$99.30 MSRP: $152.00
You Save: $52.70 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Front; Disc Brake Hardware Kit; Rotor Brake Front; Disc Brake Rotor; Brake Rotor
- Position: Front
- Replaces: 4779712AA, 68192969AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2025 Chrysler Pacifica | AWD Launch Edition, L, LX, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus, Touring Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Pacifica Rotor, Front Part Number: 4721234AA
$101.77 MSRP: $260.00
You Save: $158.23 (61%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Front; Disc Brake Hardware Kit; Rotor Brake; Disc Brake Rotor; Brake Rotor
- Position: Front
- Replaces: 4721234AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 3.8L V6, 4.0L V6, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Rotor, Rear Part Number: 4721240AG
$126.23 MSRP: $226.00
You Save: $99.77 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Rear; Disc Brake Rotor; Brake Rotor
- Position: Rear
- Replaces: 4721240AC, 4721240AF, 4721240AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2008 Chrysler Pacifica | Base, LX, Limited, Touring | 3.5L V6, 3.8L V6, 4.0L V6, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Pacifica Rotor, Rear Part Number: 68223507AB
$45.18 MSRP: $113.00
You Save: $67.82 (61%)
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Rear; Rotor Brake Rear; Brake Rotor
- Position: Rear
- Replaced by: 68223507AC
- Replaces: 68223507AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, L, LX, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus, Touring Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Rotor - Brake Part Number: 68227707AC
$101.47 MSRP: $154.00
You Save: $52.53 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: ROTOR-BRAKE
- Replaced by: 68227707AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, Limited, Pinnacle, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Rotor, Front Part Number: 68280438AB
$164.29 MSRP: $246.00
You Save: $81.71 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor - Brake; Disc Brake Rotor, Front; Disc Brake Hardware Kit; Brake Rotor
- Position: Front
- Replaced by: 68280438AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Rotor - Brake Part Number: 68227781AC
$173.35 MSRP: $260.00
You Save: $86.65 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: ROTOR-BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid S Appearance, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Chrysler Pacifica Rotor - Brake Part Number: 68420068AB
$101.04 MSRP: $157.00
You Save: $55.96 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: ROTOR-BRAKE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Pacifica | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)

Chrysler Pacifica Brake Disc

Choose OEM Brake Disc that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Brake Disc follows strict manufacturing steps to lock in quality and fit. If your Chrysler Pacifica matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Pacifica parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Fixedly this Chrysler Pacifica Brake Disc is the part of the braking system that has obtained its reputation known for its reliability and performance in numerous models of Chrysler Pacifica. Among the principal components meant to produce the required level of friction to halt the wheel and therefore the vehicle, the Brake Disc is generally made from gray cast iron and sometimes includes the fancy Vane or Ventilation that is intended to manage heat. This feature is very essential in order to sustain effective braking even in the high temperature regime. In this case, Chrysler Pacifica Brake Disc distinguishes itself within the market of automotive parts through quite extraordinary designs such as drilled and slotted ones despite the fact that they enhance heat dissipation and eliminate noise but at the same time cause pad wear. Also, two-piece rotors provide better weight and thermal characteristics, which is the icing on the cake for any car enthusiast. It is recommended to conduct periodic checks of the Brake Disc because its working condition can be judged by vibrations and other abnormal sounds that occur during operation and as all passengers' safety depends on it, its wearing out is a serious problem. The Chrysler Pacifica Brake Disc works for numerous models of the Pacifica making it important in improving not only the efficiency but also safety as well. It is noted that the vehicle has received high acclaim including the 'optimal Minivan of 2016,' '2020 optimal Family Car,' and many others; Based on this, the Chrysler Pacifica Brake Disc is central to the outstanding features and dependability that citizens need from Chrysler vehicles. All in all, the Chrysler Pacifica Brake Disc is a model of quality and invention, thus making it a product to reckon to in the congested automotive market systems.

Chrysler Pacifica Brake Disc Parts and Q&A

Rotor, Rear
4721240AG
Q: How to Service the Rear Brake Disc on Chrysler Pacifica?
A:
Raise and support your vehicle, then take the tire and wheel assembly off. Before removing the caliper, you may need to slightly stiff the caliper with the piston, working gently so pressure doesn't damage it. After that, take out the two caliper guide pin bolts and lift the caliper assembly up and away from the upper adapter abutment by turning the caliper bottom away from the brake disc. Hanging the caliper with wire or cord from the vehicle will prevent damage to the brake hose. Remove the clips attaching the brake disc to the wheel mounting studs and take it off the hub. Before putting in the brakes, look over the disc and Parking Brake Shoes and then clean off any debris or corrosion on the hub face. Put the new brake disc in place on the wheel mounting studs of the hub, checking that all abutment shims are set on the caliper adapter's slide abutments. Be careful not to harm the guide pin bushings and sleeves when mounting the caliper assembly by pulling back the caliper guide pins to avoid contact with the mounting bosses. Placement has the caliper and brake shoes over top the brake disc, aligning the high end of the outside shoe with the caliper slide groove and fit and set the bottom of the caliper on the adapter on your car. Make sure to install the caliper guide pin bolts with care so they don't become cross-threaded and tighten them to 23 Nm (200 inch-lbs.). Place the wheel and tire assembly in its proper place, adjusting the nuts to 135 Nm (100 ft. lbs.) before relaxing the lowering stand for the car. First, brake several times while the car is parked to overcome air gaps and to confirm a good brake response, monitor and maintain the brake fluid and finally drive the car slowly a few times to get brakes working properly.
Rotor, Front
4721234AA
Q: How to Remove and Replace a Front Brake Disc on Chrysler Pacifica?
A:
Before taking off or changing the front brake rotor/disc, you need to raise and secure the vehicle. Following that, undo the mounting nuts and pull out the tire and wheel from the car. At times, you may need to pull the caliper pistons back just a small amount so the shoes are farther from the rotor and caliper can be easily removed from the knuckle; this can often be done by holding the caliper at its rear and pulling away while still using the guide pins, making sure not to touch the piston to keep it safe. After that, unscrew the two bolts that hold the disc Brake Caliper adapter to the knuckle. Remove the disc brake caliper and adapter as one part from the knuckle, then hang it clear of other work using wire or a bungee cord so the hose isn't stretched. After that, take off any clips locking the brake rotor to the wheel studs and remove the brake rotor from the hub and bearing.