How Does a Blend Door Actuator Differ in Single Zone vs. Dual Zone HVAC Systems, and What Safety Measures Are Needed on Chrysler Voyager?

A single zone system requires servicing just the one blend door actuator, but a dual zone system requires two, one each for the driver's and passenger's sides, with the same service steps. Prior to handling components near the steering wheel, steering column or instrument panel that may affect air bag deployment, the air bag system should be disabled by disconnecting the battery cable and waiting two minutes for all charge to pass before shipping or lifting the vehicle. Start by unplugging the black battery cable and then pull the silencer from its spot near where the instrument panel attaches at the driver's end. After that, remove the three screws holding the heater core shield onto the left of the HVAC distribution housing and pull the shield backward to unlock the two location tabs. Take the heater core shield off the distribution housing, disconnect the wire harness from the blend door actuator and remove the two screws holding the actuator to the housing to remove it. Start by setting the new blend door actuator onto the front of the heater/air conditioner, making sure the splines on the actuator match up with the linkage of the blend air door, if it is necessary. Use the screws to secure the actuator, tighten each to 2 Nm and then join the HVAC wire harness again. Set the heater core shield securely onto the distribution housing, so the tabs fit right and attach the three screws, tightening them to 2 Nm (17 in. lbs.). Install the silencer below the driver side part of the instrument panel, attach the negative battery cable and repeat the heater-A/C control calibration process.

OEM Chrysler Voyager Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Blend Door Actuators found

View related parts
Chrysler Voyager Actuator Part Number: 4734058AB
$122.15 MSRP: $194.00
You Save: $71.85 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - Blend Door; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator Blend Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Actuator Part Number: 68164960AA
$72.20 MSRP: $108.00
You Save: $35.80 (34%)
ADD TO CART
Product Specifications
- Other Name: Actuator - Air Inlet; HVAC Air Adjustment Control Motor; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator Recirculation Door; Actuator Air Inlet
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Actuator Part Number: 68308956AA
$41.38 MSRP: $60.50
You Save: $19.12 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Heater Blend Door Actuator; Actuator A/C And Heater
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Actuator, Rear Part Number: 68313477AA
$28.27 MSRP: $41.65
You Save: $13.38 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door Actuator, Rear; HVAC Heater Blend Door Actuator; Actuator A/C And Heater
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Actuator Part Number: 68308957AA
$33.97 MSRP: $50.00
You Save: $16.03 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Heater Blend Door Actuator; Actuator A/C And Heater
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Actuator, Front Part Number: 68309067AA
$59.15 MSRP: $88.45
You Save: $29.30 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door Actuator, Front; HVAC Heater Blend Door Actuator; Actuator A/C And Heater
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2025 Chrysler Voyager | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Voyager Alternator Part Number: 4734026
Product Specifications
- Other Name: Actuator - Mode Control; HVAC Heater Blend Door Actuator; Actuator; Actuator Mode Control See Note; Actuator, Mode Control Door; Actuator Mode Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Actuator, Rear Part Number: 4885465AA
Product Specifications
- Other Name: Actuator - A/C And Heater; HVAC Air Inlet Door Actuator, Rear; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator A/C And Heater
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Voyager | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Actuator Part Number: 4734225AB
Product Specifications
- Other Name: Actuator - Recirculation Door; HVAC Heater Blend Door Actuator; Actuator Recirculation Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Voyager Actuator Part Number: 4734047AB
Product Specifications
- Other Name: Actuator - Mode Control; Actuator Mode Control
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Voyager | Base, SE | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS

Chrysler Voyager Blend Door Actuator

Choose OEM Blend Door Actuator that meet Chrysler factory standards. Chrysler designs and tests every component for precision and durability. Each Blend Door Actuator follows strict manufacturing steps to lock in quality and fit. If your Chrysler Voyager matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Voyager parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

Chrysler Voyager Blend Door Actuator Parts and Q&A

Actuator, Rear
4885465AA
Q: How Does a Blend Door Actuator Differ in Single Zone vs. Dual Zone HVAC Systems, and What Safety Measures Are Needed on Chrysler Voyager?
A:
A single zone system requires servicing just the one blend door actuator, but a dual zone system requires two, one each for the driver's and passenger's sides, with the same service steps. Prior to handling components near the Steering Wheel, steering column or instrument panel that may affect air bag deployment, the air bag system should be disabled by disconnecting the battery cable and waiting two minutes for all charge to pass before shipping or lifting the vehicle. Start by unplugging the black battery cable and then pull the silencer from its spot near where the instrument panel attaches at the driver's end. After that, remove the three screws holding the heater core shield onto the left of the HVAC distribution housing and pull the shield backward to unlock the two location tabs. Take the heater core shield off the distribution housing, disconnect the wire harness from the blend door actuator and remove the two screws holding the actuator to the housing to remove it. Start by setting the new blend door actuator onto the front of the heater/air conditioner, making sure the splines on the actuator match up with the linkage of the blend air door, if it is necessary. Use the screws to secure the actuator, tighten each to 2 Nm and then join the HVAC wire harness again. Set the heater core shield securely onto the distribution housing, so the tabs fit right and attach the three screws, tightening them to 2 Nm (17 in. lbs.). Install the silencer below the driver side part of the instrument panel, attach the negative battery cable and repeat the heater-A/C control calibration process.