How to Install the Air Bag Control Module on Jeep Liberty?

Before installing the ORC, first stop the SRS by disconnecting the negative battery cable and then wait two minutes for the system capacitor to drain, to avoid accidental air bag activation. Align the ORC and its fitting bracket over the left side studs on the TRX AT, with the floor panel transmission tunnel allowing you to easily locate those studs first. Using the screws supplied, fasten the right side of the ORC mounting bracket and tighten till they read 10.5 Nm (95 in. lbs.), then make sure the left side is secure with two nuts, again tightened to this level. Connect both wire harness connectors to the ORC receptacles and make sure the latches are secured. Attach the center console back onto the top of the floor panel transmission tunnel. Do not attach the negative cable of the battery to the battery terminal until the SRS verification test is done following any service to an SRS component.

How to Safely and Correctly Service the Air Bag Control Module on Jeep Liberty?

Before servicing the air bag Control Module, shut off the supplemental restraint system by removing and disconnecting the negative battery cable and then let it sit for two minutes so the capacitor can safely lose any stored electrical charge. Do not touch or damage the air bag Control Module, because it may hurt the impact sensor and once dropped, it can only be replaced. Make sure you don't bend or break the cover latches as you take the module out. Start by taking out the center console lying on the top of the floor panel transmission tunnel. Pull back the two latch tabs on both sides of the cover, then lift the release tab and lever arm to hook up the ACM wire harnesses. Take out the three screws and remove the ACM from the bracket underneath the transmission tunnel. Install the ACM making sure that the line on the box faces forward and that the pin line ups with the hole in the bracket. Install the ACM by inserting each screw and tightening all three to 11 Nm. Before inserting the wire harness connectors, make sure the fastening on the levers is unlatched. Fit the cover into the ACM frame, checking that both of the latches are snapped together and then put it back in the center console. Do not attach the negative battery cable until the test for the supplemental restraint system has been done following any repairs to its parts.

OEM Jeep Liberty Air Bag Control Module

SRS Airbag Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Air Bag Control Modules found

View related parts
Jeep Liberty Control Module Part Number: 56054603AE
$279.57 MSRP: $428.00
You Save: $148.43 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 56054603AB, 56054603AC, 56054503AA, 56054603AA, 56054603AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Air Bag Sensor, Rear Part Number: 56010319AC
$113.37 MSRP: $156.00
You Save: $42.63 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Air Bag; Air Bag Impact Sensor, Rear; Side Impact Sensor; Diagnostic Module
- Position: Rear
- Replaces: 56010319AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Jeep Liberty | Limited, Renegade, Sport | 2.4L L4, 3.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 68290977AA
$372.57 MSRP: $887.00
You Save: $514.43 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module
- Replaces: 68266953AA, 56010501AI, 68266953AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Jeep Liberty | Limited, Renegade, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 68290975AA
$69.94 MSRP: $168.00
You Save: $98.06 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module
- Replaces: 56010501AG, 56010501AE, 56010501AF, 68266952AB, 68266952AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002 Jeep Liberty | Limited, Renegade, Sport | 2.4L L4, 3.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Position Sensor Part Number: 4896049AB
$257.47 MSRP: $392.00
You Save: $134.53 (35%)
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Classification; Occupant Module; Module Occupant Classification
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2012 Jeep Liberty | Jet, Limited, Renegade, Sport | 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 56054160AF
$290.62 MSRP: $442.00
You Save: $151.38 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Diagnostic Unit; Module Occupant Restraint
- Replaces: 56054160AA, 56054160AC, 56054160AD, 56054160AB, 4896139AE, 56054160AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Jeep Liberty | Limited, Sport | 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Diagnostic Unit Part Number: 56054177AA
$297.98 MSRP: $444.00
You Save: $146.02 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Module Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Jeep Liberty | Limited, Sport | 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 4606998AB
$216.29
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Module Occupant Restraint
- Replaces: 4606998AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Sport | 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 56038961AB
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Module Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Jeep Liberty | Limited, Renegade, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 56038862AB
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Module Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Jeep Liberty | Limited, Renegade, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module, Driver Side Part Number: 56009899AD
Product Specifications
- Other Name: Module - Air Bag Control; Air Bag Control Module, Left; Side Impact Inflator Module
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Jeep Liberty | Limited, Renegade, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module, Passenger Side Part Number: 56009898AD
Product Specifications
- Other Name: Module - Air Bag Control; Air Bag Control Module, Right; Side Impact Inflator Module
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Jeep Liberty | Limited, Renegade, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 56054178AA
Product Specifications
- Other Name: Module - Occupant Restraint
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Jeep Liberty | Limited, Sport | 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 4606944AD
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module
- Replaces: 4606944AC, 4606944AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2006 Jeep Liberty | Limited, Renegade, Rocky Mountain Edition, Sport | 2.4L L4, 2.8L L4, 3.7L V6, 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 55352877AH
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Control Module
- Replaces: 55352877AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004 Jeep Liberty | Limited, Renegade, Sport | 4 Cyl 2.4 L GAS, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 4606946AD
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module
- Replaces: 4606946AC, 4606946AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2006 Jeep Liberty | Limited, Renegade, Rocky Mountain Edition, Sport | 2.4L L4, 2.8L L4, 3.7L V6, 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 55352877AM
Product Specifications
- Other Name: Module - Occupant Classification; Air Bag Control Module; Passenger Discriminating Sensor
- Replaces: 55352877AK, 55352877AL
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Rocky Mountain Edition, Sport | 2.4L L4, 2.8L L4, 3.7L V6, 4 Cyl 2.4 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS
View related parts
Jeep Liberty Control Module Part Number: 4606997AB
Product Specifications
- Other Name: Module - Occupant Restraint; Air Bag Control Module; Module Occupant Restraint
- Replaces: 4606997AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Jeep Liberty | 65th Anniversary Edition, Limited, Renegade, Sport | 4 Cyl 2.8 L DIESEL, 6 Cyl 3.7 L GAS

Jeep Liberty Air Bag Control Module

Choose OEM Air Bag Control Module that meet Jeep factory standards. Jeep designs and tests every component for precision and durability. Each Air Bag Control Module follows strict manufacturing steps to lock in quality and fit. If your Jeep Liberty matters to you, OEM parts make the smart choice. You'll get the exact look, feel, and performance you expect. Shop genuine Liberty parts at the highly competitive prices online. Enjoy a manufacturer's warranty, a hassle-free return policy, and rapid delivery. No more guesswork with off brands. Get genuine parts with exact fit and true factory performance. Shop with confidence today at JeepPartsDeal.com.

As part of the electronic safety components the Jeep Liberty Air Bag Control Module keeps the supplementary restraint system operational with a reputation for dependable service. The module performs an essential function by tracking collision sensors while warning about impacts to activate airbags in substantial vehicle strikes for passenger safety. The Air Bag Control Module from the Jeep Liberty exists throughout distinct models from 2002 to 2012 including both KJ and KK variations which promote both performance and safety elements. The Air Bag Control Module serves vital functions after accidents through its data storage capabilities which makes it essential equipment for Jeep Liberty vehicles. Throughout its history the Jeep Liberty Air Bag Control Module adopted advanced safety features that improved in line with industry design standards. The product development at Jeep includes evolving from traditional designs to advanced nitrogen-generating solid propellant systems as evidence of their dedication to innovation. This Air Bag Control Module from the Jeep Liberty leads the automotive industry through its powerful functionality with its ability to deliver enriched safety measures. This Air Bag Control Module supports the brand Liberty models of all kinds thereby strengthening both vehicle security and reaffirming the automaker as a brand devoted to dependable automotive products.

Jeep Liberty Air Bag Control Module Parts and Q&A

Diagnostic Unit
56054177AA
Q:
How to Install the Air Bag Control Module on Jeep Liberty?
A:
Before installing the ORC, first stop the SRS by disconnecting the negative Battery Cable and then wait two minutes for the system capacitor to drain, to avoid accidental air bag activation. Align the ORC and its fitting bracket over the left side studs on the TRX AT, with the floor panel transmission tunnel allowing you to easily locate those studs first. Using the screws supplied, fasten the right side of the ORC mounting bracket and tighten till they read 10.5 Nm (95 in. lbs.), then make sure the left side is secure with two nuts, again tightened to this level. Connect both wire harness connectors to the ORC receptacles and make sure the latches are secured. Attach the Center Console back onto the top of the floor panel transmission tunnel. Do not attach the negative cable of the battery to the battery terminal until the SRS verification test is done following any service to an SRS component.
Control Module
56038961AB
Q:
How to Safely and Correctly Service the Air Bag Control Module on Jeep Liberty?
A:
Before servicing the air bag Control Module, shut off the supplemental restraint system by removing and disconnecting the negative Battery Cable and then let it sit for two minutes so the capacitor can safely lose any stored electrical charge. Do not touch or damage the air bag Control Module, because it may hurt the impact sensor and once dropped, it can only be replaced. Make sure you don't bend or break the cover latches as you take the module out. Start by taking out the Center Console lying on the top of the floor panel transmission tunnel. Pull back the two latch tabs on both sides of the cover, then lift the release tab and lever arm to hook up the ACM wire harnesses. Take out the three screws and remove the ACM from the bracket underneath the transmission tunnel. Install the ACM making sure that the line on the box faces forward and that the pin line ups with the hole in the bracket. Install the ACM by inserting each screw and tightening all three to 11 Nm. Before inserting the wire harness connectors, make sure the fastening on the levers is unlatched. Fit the cover into the ACM frame, checking that both of the latches are snapped together and then put it back in the center console. Do not attach the negative battery cable until the test for the supplemental restraint system has been done following any repairs to its parts.