How to Remove and Reinstall a Door Latch Assembly on Chrysler Crossfire?

To disconnect the front door latch, remove the trim panel from the door and then take apart the exterior door handle. After that, take the foil off the door and lift the rubber plug away (3). Then, remove the channel bolts (2) and slide down the window channel (1) through the opening in the installer's door. Take off the latch cable (8) from the clip and disconnect the latch air line (9). Unscrew the assembly screw (7) so you can take out the door lock module (6). For installation, slide the door lock module into the opening and use the screws to keep it in place. Hook line (9) to the door lock's vacuum and next connect to the lock's control cable (8). After that, install the nuts (2), the window run channel (1) and then the rubber plug (3) through that opening. After that, cover the front door with foil again, set the exterior door handle and place the trim panel on the door.

How to Service and Repair a Rear Door Latch Assembly on Chrysler 300?

Service and repair the rear door latch by first taking out the trim panel and watershield from the inside of the rear door. After that, remove the door glass channel and bracket. Open up the rear of the door, remove and release the plastic clip linking the door latch's lock link with the latch lever. Remove the link that holds the door lock together with the knob, then pop both door handle latch release clips off the latch lever. Take out the three screws that hold the latch to the outer side of the rear door's latch face. After taking out the door wire harness connector from the front door latch, unattach the latch from the front door shell. For assembly, fasten the door wire harness plug to the latch, put the latch on the inside of the rear door and tighten the three screws to 12 N.m or 108 in.lbs. Use the exterior door handle latch release link to open it, then hook the plastic clip onto it. After that, do the same for the interior side. Line up the link, knob unit and interior door latch lock by placing them all in the rear door and aligning them with the latch lever, then keep them in place with the clip. Place the door glass channel and bracket and then the watershield and trim panel next. After that, open the outer latch access slot and turn the wrench to loosen the screw there. Push the outside latch release handle a few times and then tighten the screw back up when it stops.

OEM Chrysler Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

173 Door Latch Assemblys found

View related parts
Chrysler Latch, Passenger Side Part Number: 4675846AE
$51.41 MSRP: $75.20
You Save: $23.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Sliding Door Hold Open; Sliding Door Latch, Right; Door Latch Assembly; Door Lock Actuator; Door Lock; Latch Sliding Door Hold Open
- Position: Passenger Side
Fits the following Chrysler Models:
- Town & Country | 2008-2016 | 30th Anniversary Edition, LX, Limited, Limited Platinum, S, Touring, Touring L, Touring Plus, Walter P. Chrysler Signature Series | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.0 L GAS
View related parts
Chrysler Hinge, Lower Driver Side Part Number: 68185991AC
$19.95 MSRP: $29.25
You Save: $9.30 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Sliding Door Hold Open; Left Lower Roller; Left Latch; Door Assembly; Lock Actuator.; Latch; Latch Sliding Door Hold Open
- Position: Lower Driver Side
- Replaces: 68185991AB, 68185991AA
Fits the following Chrysler Models:
- Pacifica | 2017-2025 | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Premium S Appearance, Hybrid Road Tripper, Hybrid S Appearance, Hybrid Select, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Select, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2020-2025 | L, LX, LXi | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Lock, Front Passenger Side Part Number: 5109864AB
$132.51 MSRP: $198.00
You Save: $65.49 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Right; Door Lock Actuator Motor; Door Lock Actuator; Door Lock
- Position: Front Passenger Side
- Replaces: 4894516AB, 4894516AC, 5109864AA, 4894516AD
Fits the following Chrysler Models:
- Town & Country | 2004-2007 | Base, EX, LX, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Lock Actuator, Driver Side Part Number: 68314803AF
$209.61 MSRP: $309.00
You Save: $99.39 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Sliding Door; Left Sliding Door Latch; Door Lock Actuator Motor; Latch Assembly.; Latch
- Position: Driver Side
- Replaces: 68314803AE, 68314803AD, 68314803AB, 68314803AC, 68314803AA
Fits the following Chrysler Models:
- Pacifica | 2017-2023 | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2020-2023 | L, LX, LXi | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Lock Actuator, Driver Side Part Number: 68314779AD
$99.61 MSRP: $149.00
You Save: $49.39 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Sliding Door; Left Sliding Door Latch; Door Lock Actuator Motor; Latch Assembly.; Latch
- Position: Driver Side
- Replaces: 68314779AB, 68314779AC, 68314779AA
Fits the following Chrysler Models:
- Pacifica | 2017-2023 | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2020-2023 | L, LX, LXi | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Lock Actuator, Passenger Side Part Number: 68314778AD
$97.25 MSRP: $145.00
You Save: $47.75 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Sliding Door; Right Sliding Door Latch; Door Lock Actuator Motor; Latch Assembly; Lock Actuator; Latch
- Position: Passenger Side
- Replaces: 68314778AC, 68314778AA, 68314778AB
Fits the following Chrysler Models:
- Pacifica | 2017-2023 | AWD Launch Edition, Hybrid Limited, Hybrid Pinnacle, Hybrid Platinum, Hybrid Premium, Hybrid Touring, Hybrid Touring L, Hybrid Touring Plus, L, LX, Limited, Pinnacle, Touring, Touring L, Touring L Plus, Touring Plus | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6 L PLUG-IN HYBRID EV-GAS (PHEV)
- Voyager | 2020-2023 | L, LX, LXi | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chrysler Lock Part Number: 4675631
$8.73 MSRP: $50.10
You Save: $41.37 (83%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Front Door Manual; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Latch, Door
Fits the following Chrysler Models:
- Town & Country | 1996-1999 | Base, LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Lock Actuator, Front Passenger Side Part Number: 4589426AG
$138.13 MSRP: $207.00
You Save: $68.87 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Right; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Latch; Latch Front Door; Door Latch Assembly
- Position: Front Passenger Side
- Replaces: 4589426AF
Fits the following Chrysler Models:
- Sebring | 2008-2010 | LX, Limited, Touring | 2.4L L4, 2.7L V6, 3.5L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Lock Part Number: 4658991
$73.59 MSRP: $109.00
You Save: $35.41 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Front Door Override W/O Power; Door Lock Actuator Motor; Latch Assembly; Actuator.; Latch Assembly, Door Override; Latch Front Door; Latch Assembly
- Replaced by: 4783815AB
Fits the following Chrysler Models:
- Sebring | 1996-1998 | JX, JXi | 4 Cyl 2.4 L GAS, 6 Cyl 2.5 L GAS
View related parts
Chrysler Lock Actuator, Front Driver Side Part Number: 4589421AG
$151.49 MSRP: $215.00
You Save: $63.51 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Left; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Latch; Latch Front Door; Door Latch Assembly
- Position: Front Driver Side
- Replaces: 4589421AF
Fits the following Chrysler Models:
- Sebring | 2008-2010 | LX, Limited, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Chrysler Lock Part Number: 4719358
Product Specifications
- Other Name: Latch - Assembly - Sliding Door; Door Lock Actuator Motor; Door Latch Assembly; Door Lock Actuator; Door Lock; Latch; Latch, Remote Control
Fits the following Chrysler Models:
- Town & Country | 1990-1995 | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Latch, Front Passenger Side Part Number: MR970918
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Right; Door Lock Actuator; Door Lock; Latch Front Door; Door Latch Assembly
- Position: Front Passenger Side
Fits the following Chrysler Models:
- Sebring | 2003-2005 | Base, LX, LXi, Limited | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Lock Part Number: 4675630
Product Specifications
- Other Name: Latch - Front Door Manual; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Latch, Door
Fits the following Chrysler Models:
- Town & Country | 1996-1999 | Base, LX, LXi, Limited, SX | 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chrysler Latch, Passenger Side Part Number: 68030816AA
Product Specifications
- Other Name: Latch - Sliding Door Hold Open; Sliding Door Latch, Right; Door Latch Assembly; Door Lock Actuator; Door Lock; Latch Sliding Door Hold Open
- Position: Passenger Side
- Replaces: 4894026AA
Fits the following Chrysler Models:
- Town & Country | 2001-2007 | Base, EL, EX, LX, LXi, Limited, Touring | 3.3L V6, 3.5L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2001-2003 | LX | 2.4L L4, 3.3L V6, 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Lock, Front Driver Side Part Number: 5109861AB
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Left; Door Lock Actuator Motor; Door Lock Actuator; Door Lock
- Position: Front Driver Side
- Replaces: 4717801AC, 5109861AA, 4717801AD, 4717801AE
Fits the following Chrysler Models:
- Town & Country | 2001-2007 | Base, EL, EX, LX, LXi, Limited, Touring | 3.3L V6, 3.8L V6, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
- Voyager | 2001-2003 | Base, Ec, LX | 4 Cyl 2.4 L GAS, 6 Cyl 3.3 L FLEX, 6 Cyl 3.3 L GAS
View related parts
Chrysler Latch Assembly, Rear Driver Side Part Number: 4878829AG
Product Specifications
- Other Name: Latch - Rear Door; Rear Left Door Latch Assembly; Lock Actuator Motor; Lock Actuator.; Lock; Latch
- Position: Rear Driver Side
- Replaces: 4878829AC, 4878829AF, 4878829AE, 4878829AD
Fits the following Chrysler Models:
- Sebring | 2001-2006 | Base, LX, LXi, Limited, TSi, Touring | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Lock, Front Part Number: 5056174AE
Product Specifications
- Other Name: Latch - Front Door; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Latch Front Door
- Position: Front
- Replaced by: 5056174AF
Fits the following Chrysler Models:
- Sebring | 2006 | Limited, TSi, Touring | 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Lock, Front Part Number: 4878832AH
Product Specifications
- Other Name: Latch - Front Door; Door Lock Actuator Motor; Door Lock Actuator; Door Lock; Latch Front Door
- Position: Front
- Replaced by: 4878832AI
Fits the following Chrysler Models:
- Sebring | 2001-2006 | Base, LX, LXi, Limited, TSi, Touring | 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS
View related parts
Chrysler Latch Assembly, Front Passenger Side Part Number: 4878832AI
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Right; Door Latch Assembly; Door Lock Actuator; Door Lock; Latch
- Position: Front Passenger Side
- Replaces: 4878832AF, 4878832AH, 4878832AD, 4878832AE, 4878832AG
Fits the following Chrysler Models:
- Sebring | 2001-2006 | Base, LX, LXi, Limited, TSi, Touring | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chrysler Latch, Front Passenger Side Part Number: 4880048AI
Product Specifications
- Other Name: Latch - Front Door; Door Latch Assembly, Front Right; Door Latch Assembly; Door Lock Actuator; Door Lock
- Position: Front Passenger Side
- Replaces: 4880048AG, 4880048AF, 4880048AC, 4880048AH, 4880048AE
Fits the following Chrysler Models:
- Sebring | 2001-2006 | Base, GTC, LX, LXi, Limited, Touring | 2.4L L4, 2.7L V6, 4 Cyl 2.4 L GAS, 6 Cyl 2.7 L FLEX, 6 Cyl 2.7 L GAS

| Page 1 of 9 |Next >

1-20 of 173 Results

Chrysler Door Latch Assembly

OEM parts sourced directly from Chrysler deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Chrysler Door Latch Assembly for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Chrysler Door Latch Assembly prevents doors that open and shut in a tight fashion so that cabins are safe and you can concentrate on the drive. In 1925, Chrysler rocked the market by demonstrating that good construction and reasonable prices could go together. Chrysler then made engine vibration a thing of the past with Floating Power and made long journeys a dream without the shocks and bruises. Blown backward airflow punched sheet-metal holes clear through the wind, hence cabins ran cooler and voices remained audible. The family haulers also got better as the first actual minivan was introduced to the market by Chrysler, enabling parents to have a place to put their belongings without busing. During decades, the company continued to lengthen legroom, soften suspensions, and cut down purchasing headaches to make newcomers feel at home. The current Chrysler mentality continues to lean towards practicality over glitz where drivers can have more fun in the car than the logo. The Door Latch Assembly is a part located within both door shells to connect exterior handles, interior levers, power actuators, and striker posts in such a way that one yank or motor pulse pulls down the cams, releases pawls, and closes or releases the portal. The Door Latch Assembly snaps into the striker, making it impossible to unlock the vehicle by thieves, as well as preventing the door from being popped open by a side impact. Wear indicates when Door Latch Assembly adhesive is sticking, handles are loose, or the power lock motor is straining. A replacement Door Latch Assembly can also be applied to reclaim lost key-turn snap, clean handle feel, and complete sensor feedback to the security module.

Chrysler Door Latch Assembly Parts and Q&A

Lock
5102812AA
Q: How to Remove and Reinstall a Door Latch Assembly on Chrysler Crossfire?
A:
To disconnect the front door latch, remove the trim panel from the door and then take apart the exterior door handle. After that, take the foil off the door and lift the rubber plug away (3). Then, remove the channel bolts (2) and slide down the window channel (1) through the opening in the installer's door. Take off the latch cable (8) from the clip and disconnect the latch air line (9). Unscrew the assembly screw (7) so you can take out the door lock module (6). For installation, slide the door lock module into the opening and use the screws to keep it in place. Hook line (9) to the door lock's vacuum and next connect to the lock's control cable (8). After that, install the nuts (2), the window run channel (1) and then the rubber plug (3) through that opening. After that, cover the front door with foil again, set the exterior door handle and place the trim panel on the door.
Lock Actuator, Rear Driver Side
4575893AB
Q: How to Service and Repair a Rear Door Latch Assembly on Chrysler 300?
A:
Service and repair the rear door latch by first taking out the trim panel and watershield from the inside of the rear door. After that, remove the door glass channel and bracket. Open up the rear of the door, remove and release the plastic clip linking the door latch's lock link with the latch lever. Remove the link that holds the door lock together with the knob, then pop both door handle latch release clips off the latch lever. Take out the three screws that hold the latch to the outer side of the rear door's latch face. After taking out the door wire harness connector from the front door latch, unattach the latch from the front door shell. For assembly, fasten the door wire harness plug to the latch, put the latch on the inside of the rear door and tighten the three screws to 12 N.m or 108 in.lbs. Use the exterior door handle latch release link to open it, then hook the plastic clip onto it. After that, do the same for the interior side. Line up the link, knob unit and interior door latch lock by placing them all in the rear door and aligning them with the latch lever, then keep them in place with the clip. Place the door glass channel and bracket and then the watershield and trim panel next. After that, open the outer latch access slot and turn the wrench to loosen the screw there. Push the outside latch release handle a few times and then tighten the screw back up when it stops.