How to Service and Repair a Transmission Mount on Dodge Ram 1500?

Before you service or repair the transmission mount, lift the vehicle on a hoist and put a transmission jack under the transmission. After removing the support cushion stud nuts, elevate the back end of both the engine and transmission slightly. After that, undo the screws connecting the support cushion to the transmission support bracket and lift the piece out. Should you need to, unscrew the bolts that hold the transmission support bracket to the transmission. To install the bracket, fix it back to the transmission as shown and install new bolts, securing them to a recommended tightness of 88 Nm (65 ft. lbs.). After that, place the support cushion onto the transmission support bracket, attach the stud nuts to it and tighten them to 41 Nm (30 ft. lbs.). With the transmission jack in place, lower the transmission and cushion onto the crossmember, put in the cushion bolts and tighten each to 41 Nm (30 ft. lbs.). Afterward, take out the transmission jack and slowly drive the vehicle down from the braces.

How to Service a Transmission Mount on Dodge Ram 2500?

Before you even touch the transmission mount, make sure the car is safely raised and a transmission jack is below the mid-section. Taking out the support cushion stud nuts, now slightly raise the back of the transmission and engine. Then, eliminate the bolts holding the support cushion in place and lift it out. Should you need to, also take out the bolts securing the transmission support bracket to the transmission. If the transmission support bracket was taken off, slide it back on the transmission and secure with three new bolts which should be tightened to 102 Nm (75 ft. lbs.) torque. After that, place the support cushion onto the transmission support bracket, fit the stud nuts and tighten them until you reach 47 Nm (35 ft. lbs.) torque. Raise the transmission and support cushion out of the vehicle using the transmission jack. Next, place them onto the crossmember, then attach the bolts and tighten each one to 47 Nm (35 ft. lbs.) torque. Remove the transmission jack and bring the vehicle down onto the ground.

OEM Dodge Transmission Mount

Transfer Case Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

213 Transmission Mounts found

View related parts
Dodge Transmission Mount Bracket Part Number: 55366619AE
$168.82 MSRP: $251.00
You Save: $82.18 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Bracket Transmission Mount; Transmission Mount
- Replaces: 55366619AI, 55366619AD, 55366619AC, 55366619AF
Fits the following Dodge Models:
- Ram 1500 | 2006-2008 | Laramie, SLT, ST, SXT, Sport, TRX4 | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Front Mount, Passenger Side Part Number: 5038766AB
$141.50 MSRP: $212.00
You Save: $70.50 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Mount; Engine Mount Right
- Position: Passenger Side
Fits the following Dodge Models:
- Challenger | 2015-2023 | SRT Demon, SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock | 8 Cyl 6.2 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 5038752AA
$64.73 MSRP: $97.10
You Save: $32.37 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount Bracket; Transfer Case Mount; Bracket Transmission Mount; Transmission Mount
Fits the following Dodge Models:
- Challenger | 2020-2023 | SRT Demon 170, SRT Hellcat, SRT Hellcat Jailbreak, SRT Hellcat Redeye, SRT Hellcat Redeye Jailbreak, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak, SRT Super Stock | 8 Cyl 6.2 L GAS
- Charger | 2018-2023 | SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS
View related parts
Dodge Motor Mount, Driver Side Part Number: 5038789AA
$189.79 MSRP: $284.00
You Save: $94.21 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator; Engine Mount, Left; Engine Mount Bracket; Mount; Engine Mount Left
- Position: Driver Side
Fits the following Dodge Models:
- Charger | 2015-2023 | SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS
View related parts
Dodge Transmission Mount Part Number: 68032662AF
$52.55 MSRP: $77.10
You Save: $24.55 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Isolator - Transmission Mount; Automatic Transmission Mount; Mount; Isolator Transmission Mount
- Replaces: 68032662AD, 68032662AE
Fits the following Dodge Models:
- Durango | 2013-2025 | Citadel, GT, GT Plus, GT Premium, Limited, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, Rallye, SXT, SXT Plus, Special Service | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 68275992AA
$266.26 MSRP: $391.00
You Save: $124.74 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount Bracket; Transfer Case Mount; Bracket Transmission Mount; Transmission Mount
- Replaces: 68185207AB
Fits the following Dodge Models:
- Durango | 2014-2025 | Citadel, GT, GT Plus, GT Premium, Limited, Pursuit, SXT, SXT Plus, Special Service | 3.6L V6, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Dodge Motor Mount, Passenger Side Part Number: 5038790AA
$196.53 MSRP: $296.00
You Save: $99.47 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator; Engine Mount, Right; Engine Mount Bracket; Mount; Engine Mount Right
- Position: Passenger Side
Fits the following Dodge Models:
- Charger | 2015-2023 | SRT Hellcat, SRT Hellcat Redeye Widebody, SRT Hellcat Redeye Widebody Jailbreak, SRT Hellcat Widebody, SRT Hellcat Widebody Jailbreak, SRT Jailbreak | 8 Cyl 6.2 L GAS
View related parts
Dodge Transmission Mount Part Number: 68084749AB
$47.88 MSRP: $70.30
You Save: $22.42 (32%)
ADD TO CART
Product Specifications
- Other Name: Mount - Transmission; Automatic Transmission Mount; Transfer Case Mount; Mount Transmission
Fits the following Dodge Models:
- Charger | 2011-2023 | Pursuit, R/T, SE | 8 Cyl 5.7 L GAS
View related parts
Dodge Transmission Mount Part Number: 55398317AD
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount; Transfer Case Mount; Bracket Transmission Mount
Fits the following Dodge Models:
- Ram 1500 | 2009-2010 | SLT, ST, Sport, TRX, TRX4 | 8 Cyl 5.7 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 68275990AA
$149.56 MSRP: $222.00
You Save: $72.44 (33%)
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount Bracket; Transfer Case Mount; Bracket Transmission Mount; Transmission Mount
- Replaces: 68103009AC
Fits the following Dodge Models:
- Durango | 2014-2025 | Citadel, Limited, Pursuit, R/T, R/T Hemi Orange, R/T Plus, R/T Premium, Rallye, SXT, Special Service | 5.7L V8, 6 Cyl 3.6 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 52020936AB
Product Specifications
- Other Name: Bracket - Transmission Mount; Manual Transmission Mount Bracket; Transfer Case Mount; Bracket Transmission Mount; Transmission Mount
Fits the following Dodge Models:
- Ram 1500 | 2002-2004 | Laramie, SLT, ST | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 52020970AC
Product Specifications
- Other Name: Bracket - Transmission Mount; Manual Transmission Mount Bracket; Transfer Case Mount; Bracket Transmission Mount; Transmission Mount
Fits the following Dodge Models:
- Ram 1500 | 2002-2004 | Laramie, SLT, ST | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS
View related parts
Dodge Rear Mount Upper Bracket Part Number: 52058695
Product Specifications
- Other Name: Support - Transmission Mount; Bracket Assembly, Transmission Rear Support; Bracket, Rear Transmission Mounting; Bracket Transmission Mount
Fits the following Dodge Models:
- Ram 2500 | 1994-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL
- Ram 3500 | 1994-2002 | Base | 10 Cyl 8.0 L GAS, 6 Cyl 5.9 L DIESEL
View related parts
Dodge Transmission Mount Part Number: 55366616AH
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount
- Replaces: 55366616AC, 55366616AD, 55366616AF
Fits the following Dodge Models:
- Ram 1500 | 2006-2008 | Laramie, SLT, ST, SXT, Sport, TRX4 | 3.7L V6, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Transmission Mount Part Number: 52855231AA
Product Specifications
- Other Name: Insulator - Transmission Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Support Bracket; Rear Mount; Bracket And Insulator Transmission Support
- Replaces: 52021320AB
Fits the following Dodge Models:
- Durango | 2004-2009 | Adventurer, Limited, SE, SLT, ST, SXT | 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
- Ram 1500 | 2002-2005 | Laramie, SLT, ST | 3.7L V6, 5.7L V8, 6 Cyl 3.7 L GAS, 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.9 L GAS
View related parts
Dodge Transmission Mount Part Number: 52855230AA
Product Specifications
- Other Name: Insulator - Transmission Support; Trans Mt Bracket; Engine Mt Bracket; Transfer Case Mt; Motor Mt; Support Bracket; Rear Mount; Bracket And Insulator Transmission Support
Fits the following Dodge Models:
- Durango | 2004-2009 | Adventurer, Limited, SE, SLT, ST, SXT | 8 Cyl 4.7 L FLEX, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 5037743AC
Product Specifications
- Other Name: Bracket - Transmission Mount; Manual Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Bracket Transmission Mount; Transmission Mount
- Replaces: 5037743AB
Fits the following Dodge Models:
- Ram 1500 | 2006 | SRT-10 | 10 Cyl 8.3 L GAS
View related parts
Dodge Transmission Mount Part Number: 55366619AH
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount; Transfer Case Mount; Bracket Transmission Mount
Fits the following Dodge Models:
- Ram 1500 | 2009-2010 | SLT, ST, TRX, TRX4 | 8 Cyl 4.7 L FLEX
View related parts
Dodge Front Mount, Passenger Side Part Number: 5038830AB
$112.11 MSRP: $167.00
You Save: $54.89 (33%)
Product Specifications
- Other Name: Isolator - Engine Mount; Engine Mount, Front Right; Engine Mount Bracket; Motor Mount; Mount; Isolator; Isolator Engine Mount
- Position: Front Passenger Side
- Replaced by: 5038830AC
- Replaces: 5038830AA
Fits the following Dodge Models:
- Durango | 2023-2025, 2021 | SRT Hellcat, SRT Hellcat Plus, SRT Hellcat Premium | 8 Cyl 6.2 L GAS
View related parts
Dodge Transmission Mount Bracket Part Number: 5037742AC
Product Specifications
- Other Name: Bracket - Transmission Mount; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Bracket Transmission Mount; Transmission Mount
- Replaces: 5037742AB
Fits the following Dodge Models:
- Ram 1500 | 2006 | SRT-10 | 10 Cyl 8.3 L GAS

| Page 1 of 11 |Next >

1-20 of 213 Results

Dodge Transmission Mount

OEM parts sourced directly from Dodge deliver superior quality, long lasting strength, and a precise fit you can trust. Each item goes through strict quality checks to ensure safety, toughness, and performance that matches your factory equipment. At JeepPartsDeal online shop, you'll get top-quality, budget-friendly OEM Dodge Transmission Mount for your vehicle. We focus on giving you a high standard without pushing up the price. Our full selection of genuine factory products comes backed by the original manufacturer's warranty. You'll love our fast delivery, seamless shopping experience, and convenient return policy, saving you all the hassle.

Dodge Transmission Mount provides the smooth operation of power to the surface without vibration. Dodge began as a small machine shop and in 1914 demonstrated to competitors through the first all-steel assembly car that was designed to be brutally strong. Dodge continued to have that swagger with rumbling HEMI engines and the mad Viper program which allowed ordinary drivers to sample track adrenaline. Dodge is now applying muscle heritage to the new sound of electricity with the Fratzonic Chambered Exhaust that roars with 600 watts or goes unheard as the mood changes. Dodge supports this loud opinion with features such as drive modes like Drag, Donut, and Sport that make it clear that versatility can still be rowdy without apology. A Transmission Mount is built like a solid bridge between the engine and the chassis which absorbs the shaking that would cause the seats to shake and the bolts to become loose. Since the Transmission Mount fixes the gearbox in position, it prevents destructive alterations in alignment and protects sensitive gears during severe launches or potholes. The mount is only changed by drivers rarely and offers more silence in rides in all types of vehicles ranging from compacts to heavy vans. New rubber and metal compound in the interior of every Transmission Mount directs the torque uniformly, making the steering wheel remain calm when the car reaches highway speed. Continuous adjustment by a new Transmission Mount also leaves nearby hoses and wiring undeveloped to wear, allowing the entire vehicle to have additional life on any road.

Dodge Transmission Mount Parts and Q&A

Rear Mount Upper Bracket
52019637
Q: How to Service and Repair a Transmission Mount on Dodge Ram 1500?
A:
Before you service or repair the transmission mount, lift the vehicle on a hoist and put a transmission jack under the transmission. After removing the support cushion stud nuts, elevate the back end of both the engine and transmission slightly. After that, undo the screws connecting the support cushion to the transmission support bracket and lift the piece out. Should you need to, unscrew the bolts that hold the transmission support bracket to the transmission. To install the bracket, fix it back to the transmission as shown and install new bolts, securing them to a recommended tightness of 88 Nm (65 ft. lbs.). After that, place the support cushion onto the transmission support bracket, attach the stud nuts to it and tighten them to 41 Nm (30 ft. lbs.). With the transmission jack in place, lower the transmission and cushion onto the crossmember, put in the cushion bolts and tighten each to 41 Nm (30 ft. lbs.). Afterward, take out the transmission jack and slowly drive the vehicle down from the braces.
Rear Mount Upper Bracket
52019641
Q: How to Service a Transmission Mount on Dodge Ram 2500?
A:
Before you even touch the transmission mount, make sure the car is safely raised and a transmission jack is below the mid-section. Taking out the support cushion stud nuts, now slightly raise the back of the transmission and engine. Then, eliminate the bolts holding the support cushion in place and lift it out. Should you need to, also take out the bolts securing the transmission support bracket to the transmission. If the transmission support bracket was taken off, slide it back on the transmission and secure with three new bolts which should be tightened to 102 Nm (75 ft. lbs.) torque. After that, place the support cushion onto the transmission support bracket, fit the stud nuts and tighten them until you reach 47 Nm (35 ft. lbs.) torque. Raise the transmission and support cushion out of the vehicle using the transmission jack. Next, place them onto the crossmember, then attach the bolts and tighten each one to 47 Nm (35 ft. lbs.) torque. Remove the transmission jack and bring the vehicle down onto the ground.